TScale RWP Bedienungsanleitung

RWP

Weighing Indicator

V1.16

REV:Y1,May 2016

RWP Weighing Indicator Technical Manual(v1.16)

CONTENTS

1. SPECIFICATIONS….………………………………………………….……......4

2. INTRODUCTION………………………………………………………………...6

3. INSTALATION …………………………………………………………………..7

Unpacking…………………………………………………………………..7

Installation…………………………………………………………………..7

Load cell connections..………………………………………………...8

Connect Adaptor and Charging..………………………………………...8

4. DESCRIPTION……………...........……………………………………………...9

Display……………………………………………………………………....9

Key board……………………………………………………………..…….10

5. OPERATION.…………………….………………………………….………….11

5.1. Power ON/OFF……………………………………………..………..11

5.2. Zero…………………….................................................................11

5.3.Tare................................................................11

5.4. Sample Weighing………………………………………….………….11

5.5. Check Weighing…………………………………………….…………11

5.6. Enter to Menu………………………………….…………………….12

5.7. Set Limits…………………..............................................................12

5.8. Set check weighing mode..............................................................12

5.9. Accumulation……………………………………….………………….13

5.10. Accumulation automatically……………………..………………...13

5.11. Animal Weighing…………………………………………………...14

5.12. Backlight Setting…………………………………………………15

5.13. Auto Power Off Setting……………………………………………15

5.14. Peak Hold……………………………………………………………15

5.15. Subtraction scale…………………………………………………15

6. PARAMETER…………………………………………….…………………….16

Keys operation into menu…………………………………………….. .16

Parameter Block………………………………………………………....17

7. CALIBRATION…………………………………………………………………21

8. RS232 OUT PUT………………………………………………………………24

9. DRAWING…………………………………………………………..……………27

10. ERROR CODES…………………………………………………………..……29

RWP Weighing Indicator Technical Manual(v1.16)

- 4 -

1. SPECIFICATIONS

Overall View

Dimensions

RWP Weighing Indicator Technical Manual(v1.16)

- 5 -

Model

RWP

Resolution

1/30,000

Indicator housing

ABS Plastic

Stabilisation Time

1 Seconds typical

Operating Temperature

0°C ~ +40°C / 32°F - 104°F

Power supply (external)

AC Adaptor (12V/500mA) /

Ni-MH battery (1.2V/2000mAh x 6)

Calibration

Automatic External

Display

6 digits 22mm LCD display, attached backlight

Interface

RS-232 Output Optional

Zero range

0mV~5mV

Signal input range

0~15mV

ADC

Sigma delta

ADC update

Max 60 times /second

Load cell drive voltage

Max 5V/150mA

Internal counts

600,000

RWP Weighing Indicator Technical Manual(v1.16)

- 6 -

2. INTRODUCTION

The RWP series weighing indicator that amplifies signals from a load cell,

converts it to digital data and displays it as a mass value.

It is suitable for general weighing or more specialized applications such as

check weighing, animal weighing and accumulation applications.

It can connect the indicator to a printer or a PC.

Large LCD with white LED back light display

RWP Weighing Indicator Technical Manual(v1.16)

- 7 -

3. INSTALLATION

Unpacking

When you receive the scale, inspect it to make sure that it is not damaged and

that all are parts are included:

Remove the Indicator from the carton.

Remove the protective covering. Store the packaging and to use if you

need to transport the scale later.

Inspect the indicator for damage.

Make sure all components are included.

1. Indicator

2. Adaptor

3. Manual

4. Indicator holder (Optional)

5. Load cell Output connecter (Optional)

6. RS-232 Output Connecter (Optional)

Installation

Place the Indicator on a table or connect with proper stand.

Connect the plat form load cell cable in to the indicator load cell connecter.

Load cell connecter is locating back side of the indicator.

Connect the adaptor pin in to the indicator adaptor jack.

Adaptor jack is locating, back side of the indicator.

Adaptor connects into your AC power socket.

Pluggable equipment must be installed near an easily accessible socket

outlet with a protective ground/ earth contact.

Turn on the On/Off key. If you want to turn off, press the key again.

Display will be show the scale capacity and will be starting self-checking.

After self-checking, display will be come to normal weighing mode.

Load cell connecter

RS-232 port

Adaptor jack

Bracket

RWP Weighing Indicator Technical Manual(v1.16)

- 8 -

Warm-up time of 15 minutes stabilizes the measured values after

switching on.

Calibrate with exact calibration weights, minimum 1/3 of the scale capacity

want to use for calibration. For calibration see details in parameter.

Then you can start your operation

Load cell connections

Connect the load cell cables to the terminal as shown below.

It can connect four 350 ohm load cells.

The load cell drive voltage is 5V DC ±5% between

Excitation + and Excitation -.

Connect Adaptor and Charging

To charge the battery insert the adaptor pin to jack. Adaptor simply plug into

the mains power. The scale no needs to be turned on.

The battery should be charged 12 hours for full capacity.

The symbol status of the battery

Battery voltage has dropped

Low voltage

Fully charged

Do not use any other type of power adaptor than the one supplied with the

scale.

Verify that the AC power socket outlet is properly protected.

Note: Please charge the battery before using the scale for the first time.

5Pin

Connection

Pin 1

Signal +

Pin 2

Signal -

Pin 3

Shield

Pin 4

Exc -

Pin 5

Exc +

RWP Weighing Indicator Technical Manual(v1.16)

- 9 -

4. DESCRIPTION

Display

DISPLAY

FUNCTION

LOW

Check weighing

ZERO

Indicator for Zero display

TARE

Indicator for Tare display

GROSS

Indicator for Gross weight

NET

Indicator for Net weight

STABLE

Indicator for Display stability

AUTO

Indicator for Auto Accumulation

M+

Indicator for Accumulation

ANIMAL

Indicator for Animal Weighing Mode

HOLD

Indicator for Hold/ Lock

Indicator for Charging status of battery.

FROUNT

BACK

FROUNT

BACK

RWP Weighing Indicator Technical Manual(v1.16)

- 10 -

Key Board

KEY

FUNCTION

Turn the power On/ Off

Used to reset to Zero.

In setting mode can use to confirm entry

Used to recording tare values and change the value from gross

value to net value.

In setting mode can use to increase the value and scroll

forward in menu.

When the scale has been tared and display is in gross or net

mode.

When using the settings mode, can use to move active digits

right.

For print the results, to the PC or printer using the optional RS-

232 interface.

It also adds the value to the accumulation memory if the

accumulation function is not automatic.

When using the settings mode,can use to clear active digits

Switch to unit weight. In setting mode,

escape back to menu/ weighing mode.

When using the settings mode, can use to move active digits

left.

Inhaltsverzeichnis

Andere TScale Messgerät Handbücher

TScale

TScale TW20 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung