TYAN THUNDER K8QW Bedienungsanleitung

http://www.TYAN.com

Thunder K8QW /// S4881G2NR

Revision 1.00

manual may be reproduced or translated without prior written consent from TYAN

Computer Corp.

All registered and unregistered trademarks and company names contained in this manual

are property of their respective owners including, but not limited to the following.

TYAN, Thunder K8QW are trademarks of TYAN Computer Corporation.

AMD, Opteron, and combinations thereof are trademarks of AMD Corporation.

Nvidia and nForce are trademarks of Nvidia Corporation

Phoenix BIOS is a trademark of Phoenix Technologies.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE,is a trademark of SuSE AG.

Linux is a trademark of Linus Torvalds

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Broadcom®is a trademark of Broadcom Corporation and/or its subsidiaries

ATI and Rage XL are trademarks of ATI Corporation

Information contained in this document is furnished by TYAN Computer Corporation and

has been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose

or merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any

direct or indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this document.

http://www.TYAN.com

Table of Contents

Before you begin… Page 4

Chapter 1: Introduction

Congratulations Page 5

Hardware Specifications Page 5

Software Specifications Page 6

Chapter 2: Board Installation

2.00 Board Image Page 8

2.01 Block Diagram Page 9

2.02 Board Parts, Jumpers and Connectors Page 10

2.03 Front Panel Connector (J15) Page 12

2.04 Clear CMOS Jumper (J20) Page 13

2.05 SMBus Connector (J1) Page 13

2.06 USB 2.0 Header (J30, J31,J95) Page 14

2.07 Chassis Intrusion (JP2) Page 14

2.08 Serial Port Internal Header (J101) Page 15

2.09 PCI-X Speed Select Jumper (J11) Page 15

2.10 PCI-X Speed Select Jumper (J12) Page 16

2.11 RI Header (JP1) Page 16

2.12 Gigabit LAN1, LAN2 LED Header (JP4,JP5) Page 17

2.13 IEEE 1394A Pin Header (J27, J28) Page 17

2.14 ID Switch (J118) Page 18

2.15 ID LED (J119) Page 18

2.16 NMI (J22) Page 19

2.17 CPU Fan Connectors

(J117, J116, J108, J109) Page 19

2.18 System 4-Pin Fan Connectors

(J103, J104, J105, J106, J107, J110) Page 20

2.19 System 3-Pin Fan Connectors (J111,J112) Page 20

2.20 Parallel Header (LPT Connector) Page 21

2.21 PWR Connector (PWR3) Page 21

2.22 PWR Connector (PWR4) Page 22

2.23 OEM Reserved Connectors and Jumpers Page 23

2.24 Installing the processors Page 23

2.25 Heatsink Retention Frame Installation Page 24

2.26 Thermal Interface Material Page 25

2.27 Heatsink Installation Procedures Page 26

2.28 Finishing Installing the Heatsink Page 27

2.29 Tips on Installing Motherboard in Chassis Page 28

2.30 Installing the Memory Page 30

2.31 Attaching Drive Cables Page 33

2.32 Installing Add-In Cards Page 32

2.33 PCI Riser Cards Page 36

2.34 Connecting External Devices Page 37

2.35 Installing the Power Supply Page 37

2.36 Finishing Up Page 38

Chapter 3: BIOS

3.00 BIOS Setup Utility Page 39

3.10 BIOS Menu Bar Page 40

http://www.TYAN.com

3.20 BIOS Legend Bar Page 40

3.30 BIOS Main Menu Page 41

3.40 BIOS Advanced Menu Page 42

3.50 BIOS Memory Menu Page 57

3.60 BIOS Security Menu Page 58

3.70 BIOS Boot Menu Page 59

3.80 BIOS Power Menu Page 61

3.90 BIOS Exit Menu Page 62

Chapter 4: Diagnostics Page 63

Appendix I: Glossary Page 64

Appendix II: BIOS POST Code Page 69

Technical Support Page 72

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder K8QW motherboard

1x 34-Pin floppy drive cable

4 x SATA cable

2x SATA Drive Power Adapter

2x Ultra-DMA-100/66 IDE cable

1x Cable set: 9-pin Serial and 25-pin Parallel

1 x 1394 cable

1x Thunder K8QW user’s manual

1x Thunder K8QW Quick Reference guide

1x TYAN driver CD

1x I/O shield with 2 LAN ports

4 x CPU Mounting Kit

If any of these items are missing, please contact your vendor/dealer for replacement

before continuing with the installation process.

http://www.TYAN.com

Chapter 1: Introduction

Congratulations

You are now the owner of the ideal solution for rackmount servers, large computer

clusters, or pedestal server needs. The Tyan Thunder K8QW features support for

Quad AMD Opteron processors, dual channel Gigabit Ethernet, Serial ATA (SATA).The

Thunder K8QW also offers the option to upgrade to eight-level processing capabilities

through use of HT4881 and M4881 add-on modules.

Remember to visit TYAN’s Website at http://www.TYAN.com. There you can find

information on all of TYAN’s products with FAQs, online manuals and BIOS upgrades.

Hardware Specifications

Processor

Quad µPGA 940-pin ZIF sockets

Supports up to four Single/Dual Core

AMD OpteronTM 800 series processors

Four onboard 4-phase VRMs

Integrated 128-bit DDR Memory

controller

Chipset

NVIDIA CrushK8-04 Professional

AMD-8131TM HyperTransport I/O Hub

Winbond W83627HF Super I/O chip

Three Analog Devices ADT7468

Hardware Monitoring IC

Memory

128-bit dual channel memory bus

Sixteen 184-pin DDR DIMM sockets

(Four per CPU)

Supports up to 64 GB Reg/ECC DDR

Supports DDR266, DDR333, or DDR400

Supports Single/Dual and Quad Rank

memory

Expansion Slots

Two x16 PCI Express slot, one with x4

signals

Two independent 64-bit PCI-X buses

zOne 133 MHz max 3.3V PCI-X slot

from Bridge B

zTwo 100 MHz max 3.3V PCI-X slots

from Bridge A

Total of five usable slots

Integrated Enhanced IDE

Controller

Provides two IDE dual-drive ports

for up to four EIDE devices

Supports for UDMA 33/66/100/133

IDE drives and ATAPI compliant

devices

Integrated I/O

One floppy connector supports up to

two drives

Two 9-pin serial ports (one

connector and one header) and One

25-pin parallel port pin-header

Eight USB 2.0 EHCI ports (two rear

connectors & three headers with two

ports each)

PS/2 mouse and keyboard

connectors

System Management

Modular BMC 2x25pin header for

SMDC support

Ten 4-pin fan headers support

tachometer monitoring and smart

FAN control (PWM)

Temperature and voltage

monitoring

One 2-pin Chassis Intrusion header

Port 80h LED display

http://www.TYAN.com

Integrated SATA Controller (Mfg.

option)

One Silicon Image SI3114 controller

Four SATA 2.0 ports

Supports up to Four SATA drives

Supports RAID 0,1 and 10

Intelligent Platform Management

Interface Header

Tyan Server Management Daughter

card (Optional) supports features listed

below via IPMI header

QLogicTM Zircon Baseboard

Management Controller (BMC) based

on powerful ARM7 technology

Tailored for IPMI 1.5 Spec

Supports KCS and BT styles

Flexible Windows and Linux based

Management Solution

Supports RMCP and SNMP protocols

Supports ASF standard and EMP

I2C serial multi-master controllers and

UARTs

Built-in IPMB connector

Remote power on/off and reset support

(IPMI-over-LAN)

Hyper Transport™ Connectors

Two PCI Express x16 slots with TYAN

private signal definition which uses the

Hyper Transport to connect two HT

cards to the M4881. (CPU Board

specifically designed by TYAN).

Integrated PCI Graphics

ATI®RageTM XL PCI graphics controller

8MB Frame Buffer of video memory

Integrated LAN Controllers

Broadcom®BCM5704C dual-

channel Gigabit Ethernet

controller

Two RJ-45 LAN connectors with

LEDs

Connected to PCI-X Bridge A

Two Front Panel LED headers

BIOS

Phoenix BIOS

4Mbit LPC Flash ROM

Watchdog timer

USB boot support

48-bit LBA Support

Supports PXE via Ethernet

Power management:S0, S1, S4

and S5

ACPI 2.0 & 1.0B support

Form Factor

SSI MEB footprint (13” x 16” /

330.2mm x 406.4mm)

EPS12V power connectors

One serial port and one VGA

connector

Stacked USB 2.0 (two) connectors

Stacked PS/2 keyboard and

mouse connectors

Two RJ-45 side-by-side LAN

connectors with LEDs

Regulatory

FCC Class B (Declaration of

Conformity)

European Community CE

*Not validated at the time of print,

subject to change.

Software Specifications

OS (Operating System) Support

Microsoft Windows 2000 Server RHEL AS 3 Update 4 64-bit

Microsoft Windows 2000 Advanced Server SuSE9.0 64 bit pro, SELS 9.

Microsoft Windows 2003 Enterprise Server(32/64-bit)

Microsoft Windows 2003 Server (32/64 bit)

Other distributions of Linux pending validation

TYAN reserves the right to add support or discontinue support for any OS with or

without notice.

http://www.TYAN.com

Chapter 2: Board Installation

Precaution: The Thunder K8QW supports EPS12V power supplies (24-pin/8-pin) and will

not operate with any other types.

DO NOT USE ATX 2.x, ATX12V or ATXGES power supplies as they will damage the

board and void your warranty.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information

that will make configuration and setup much easier. Here are some precautions you

should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic

bag. Unplug the power from your computer power supply and then touch a

safely grounded object to release static charge (i.e. power supply case). For the

safest conditions, TYAN recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or

flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory

modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag

that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis,

as well as installing the processor, memory, disk drives and cables.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.TYAN.com

2.00 – Board Image

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above

picture.

The following page includes details on the vital components of this motherboard.

http://www.TYAN.com

2.01 – Block Diagram

S4881 Thunder K8QW Block Diagram

Note: The Hyper Transport speed between HT CON & CPU can reach up to 2000MT/S

http://www.TYAN.com

2.02 – Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

Andere Handbücher für THUNDER K8QW

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TYAN Hauptplatine Handbücher

TYAN

TYAN TOMCAT I7230A Bedienungsanleitung

TYAN

TYAN S5376 Bedienungsanleitung

TYAN

TYAN THUNDER 2500 Bedienungsanleitung

TYAN

TYAN S7106 Bedienungsanleitung

TYAN

TYAN Tempest i5100X S5375 Bedienungsanleitung

TYAN

TYAN 1.00 Bedienungsanleitung

TYAN

TYAN TIGER I7501X Bedienungsanleitung

TYAN

TYAN THUNDER K8HR Bedienungsanleitung

TYAN

TYAN Tempest i5100T Bedienungsanleitung

TYAN

TYAN TOLEDO I3000R Bedienungsanleitung

TYAN

TYAN THUNDER K8QW Bedienungsanleitung

TYAN

TYAN S7103 Bedienungsanleitung

TYAN

TYAN Trinity 100AT S1590 Bedienungsanleitung

TYAN

TYAN THUNDER K8QSD PRO Bedienungsanleitung

TYAN

TYAN TOMCAT I815EF Bedienungsanleitung

TYAN

TYAN TRINITY 450 Bedienungsanleitung

TYAN

TYAN TOMCAT I875PR Bedienungsanleitung

TYAN

TYAN TOMCAT I7210 Bedienungsanleitung

TYAN

TYAN S5549 Bedienungsanleitung

TYAN

TYAN TRINITY I845 Bedienungsanleitung

TYAN

TYAN THUNDER I7500 Bedienungsanleitung

TYAN

TYAN S5372-LH Bedienungsanleitung

TYAN

TYAN 1.00 Technisches Handbuch

TYAN

TYAN TOMCAT K8E Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung