U.S. Products KING COBRA 500-CSA Betriebsanleitung

KING COBRA® 500-CSA

120V

INFORMATION

OPERATING

INSTRUCTIONS

DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THE INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. Keep machine from rain and snow, extremes in temperatures, and store in a

heated location. Use the machine indoors. Do not use outdoors.

3. Do not let the pump run dry.

4. Use approved chemicals only. NO SOLVENTS.

5. Wear gloves or use rags when removing quick disconnects to prevent burns.

08.10.2007

56041956

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools,

hospitals, factories, shops and offices other than normal residential housekeeping

purposes.

When using any electrical appliance, basic precautions should always be followed,

including the following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet

when not in use and before servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only as described in this manual. Use only the manufacturer’s recommended

attachments.

•Never add water over 130º F/54º C to the solution tank.

•Do not use with damaged cord or plug. If the machine is not working as it should, has

been dropped, damaged, left outdoors or dropped into water, return it to a service center.

•Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord

around sharp edges or corners. Do not run the machine over the cord. Keep the cord away

from heated surfaces. To unplug, grasp the plug, not the cord.

•Do not handle the plug, the cord or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug

immediately if the ground prong becomes damaged.

•Do not put any object into openings. Do not use with any opening blocked; keep free of

dust, lint, hair, and anything that may reduce air flow.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving

parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot

ashes, or any health endangering dusts. Do not use to pick up flammable or combustible

liquids such as gasoline or use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature,

pressure, or chemical content.

INSPECTION:

Carefully unpack and inspect your KING COBRA-500 for shipping damage. Each machine is tested and

inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify

the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very thoroughly

they could cause a build-up in the pump, lines, heat exchanger and/or quick disconnects. Any problem

caused by a chemical build-up is not covered by warranty. Use a neutral cleaner with a pH between 5 and 10 to

avoid premature wear of the pump, seals, and/or other components. Damage caused by the use of strong

chemicals is not covered by the warranty.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day. Once a

month, minimum, run a flushing compound through the machine to break up any mineral or chemical build-

up that may have formed. The vacuum motor, pump motor, and the pump do not require any scheduled

maintenance; however, the motors may require replacement brushes after 1000 - 1500 hours. The pump may

require rebuild kits after 1000 - 1500 hours, typically, and the pump unloader valve may need to be replaced

after approximately 1000 - 1500 hours of use (refer to machine part list for numbers). Clean the body with an

all purpose detergent, and protect it with an automobile interior polish. Lubricate the wheels, castors, and quick

disconnects with an all purpose silicone spray.

Recovery

Tank Lid Switch

Plate

Vacuum Hose

Connection

Solution Hose

Connection

Vacuum

Hose and

Solution

Hose on

Reel

Latch

10 Inch

Wheel

Pressure

Gauge

4 inch

Castor

Solution Tank

Lid

Dump Hose

(on rear of

machine)

U. S. PRODUCTS

Circuit

Breaker

NOTE: This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,

shops and offices other than normal residential housekeeping purposes.

SWITCH PLATE

PUMP

PRESSURE

ADJUST

TEMPERATURE

ADJUST

CIRCUIT LOCATOR

LIGHT INDICATES

TWO CIRCUITS.

HEATER WILL

AUTOMATICALLY

TURN ON

BYPASS SWICH.

TURNS THE HEATER ON

WHEN GREEN LIGHT IS

NOT ON

3VACUUM

ON/OFF

SWITCH

INDICATES

SPRAYING

PRESSURE

GAUGE

Record the serial number and model of your new extractor here:

(and be sure to mail your warranty card)

Serial Number: __________________ Model: KING COBRA-500-CSA

Purchase Date:__________________

Write the name and phone number of your distributor:

_____________________________________

REDLIGHTINDICATES

HEATER IS HEATING

1 Inspect the machine, hoses, and cleaning tools for cleanliness and completeness.

2Fill the solution tank with water. Using warm water may be a benefit in cleaning effectiveness, but

do not use hot water (above 130

F / 54

C) in the tank.

3 Screw the lid on the recovery tank. Close the dump hose.

4 Plug in the power cords. Do not connect both cords to the same outlet; the green, circuit locator light

(1) on the switch plate should light up. If the locator light does not come on, try different outlets until it

does. If you are certain the cords are on separate circuits, turn the Bypass switch (2) on.

CAUTION: using the Bypass switch (2) when the cords are on the same circuit may cause the

breaker in the wall to trip. NOTE: the receptacle on the left (viewed from behind the machine) powers

the heater.

The red light (6) will turn on only when the heat exchanger is actively heating.

OPERATION

be sure to register your warranty -- www.usproducts.com

5 Connect the priming/siphon hose to the machine, turn the pump ON by turning the pump pressure knob

(4) up to increase pump speed, and turn the vacuum switch (3) on. Hold the rubber ‘cork’ against the

vacuum inlet hose barb on the recovery tank. The pump should prime between 20 - 60 seconds. Watch

the water flow into the recovery tank through the clear lid. When the water is clear (no air in it) and

flowing strongly, turn both the pump and the vacuum off, and remove the priming hose.

Priming may take 20 - 60 seconds, and the solution tank should be full.

6 Add liquid cleaning chemical, with a pH between 6 and 9, to the solution tank.

7 Attach the spray hose (from the reel) to the solution quick disconnect and the vacuum hose to the

hose barb on the recovery tank. Pull the hoses out from the reel. Attach the other ends of the hoses

to the cleaning tool.

8 Set the temperature knob (5) to the desired heat setting. Allow the heat exchanger two minutes to

reach operating temperature. The red light (6) will go out when the heater has reached operating

temperature. NOTE: the red light will be on nearly all the time as you clean.

9 Turn the pump on by setting the pressure adjust knob to the desired spraying pressure (0 - 500 PSI).

Read the spraying pressure at the pressure gauge (7) while spraying. NOTE: when you let off the

trigger on the wand, the pressure gauge reading will drop to 0 psi; however, the spraying pressure will

remain at the level to which you have set it. Turn the vacuum on (3). NOTE: the vacuum motor will

start up slowly to prevent a large current surge.

10 Begin cleaning.

11 Use defoamer in the recovery tank any time foaming occurs.

12 Monitor the water level in the solution tank. Do not let the pump run dry.

13 When the solution tank gets low, turn off the pump and the vacuum, fill the solution tank, empty

and clean the recovery tank.

14 When finished with the job, remove any unused solution from the solution tank, and run a few gallons of

clean water through the system. Drain the recovery tank by placing the dump hose over a drain, or a

bucket, and removing the cap. Disconnect the hoses from the cleaning tool, and reel them up onto the

hose spool.

NOTE: To remove the reel, with hoses, from the machine, pull the vacuum hose loose from the hose barb

on the front of the tank. Disconnect the solution hose quick coupling. Push Vacuum hose into the center of

the hose spool. Grasp the spool from either side, and lift it off the machine. NOTE: before servicing any

component in the base cabinet, the hoses and spool must be removed from the machine before the tanks

can be lifted open.

This unique, patented system is operated by a solid state circuit. It will inform the operator when the two

cords are plugged into separate circuits by turning on the green, circuit locator light. This helps to prevent

tripping circuit breakers. NOTE: if the green, circuit locator light does not illuminate when the cords are

plugged in, then both cords are on the same circuit. Try other outlets with one of the cords until you get

the locator light to come on. NOTE: if the bypass switch is turned on when both cords are on the same

circuit, the breaker in the wall may trip.

ELECTRIC CIRCUIT LOCATOR

REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE

ELECTRONIC FLOAT SHUT-OFF

When the recovery tank is full, the electronic float switch will turn the vacuum motor off. This will

prevent water from entering the vacuum motor. The float may not work properly if the float filter rod

is dirty or if there is heavy foam in the tank

To reset, turn the Vacuum switch off, and empty the

tank.

CAUTION: to avoid vacuum motor damage, always make sure the float filter is clean and that it

can travel freely before you operate the machine. Always use a defoamer any time foam is present.

TO ITEM 46

TO ITEM 69

11 77

16 17

TO ITEM 46

818

51A

52 53 54

56 58 59

66 67

27 46A

42 43

08/10/2007

75A

71A

69 71

U. S. PRODUCTS

KC-500-CSA

120V

81 82

KING COBRA-500-CSA EXTRACTOR

PART LIST

1 805 Chain, lid, 8”

2 901B Lid, solution tank

3 HKCR-1 Holding Tank, white

4 1088 Glide, teflon

5 331 Screw, 6-32 X 1/2”

6 925 Hose, 3/8” I.D. X 24” pump bypass

9 945D Valve, pump unloader

15 FP410 Pump, no motor

20 950D Cam/bearing assembly

21 946 Hose, 1/2” I.D. X 22-1/2” pump in

22 FP348B Hose, pump to heater, 12”

23 FP411 Hose assembly, pump to gauge

24 913 Vacuum motor, 3-stage

25 959 Gasket, vacuum motor

27 926 Manifold, vacuum motor mount

28 1136 Hose, vacuum inlet, 1-1/2” X 24 “

29 907 Hose barb, for vacuum hose

31 1156 Screw, 8-32 X 1-1/8”

32 2086A Lid, vacuum, with ring

33 1074 Gasket, lid

34 1060C Plug, drain hose

35 1060B Hose, drain, 1-1/2” X 24”

36 1518 Hose clamp

37 207A Filter, pump inlet

38 2026 Float switch

39 CWKC-BLK Cord wrap, Black

41 1146 Pipe, 6.85”, S/S

42 45 Quick connect, male, 1/4 p.t.

43 1144 Rubber sleeve, 1/2” ID X 5”

44 1062 Receptacle, power cord

45 1057B Power cord, 25 ft, 3/12, yellow

46 VKCR-1 Vacuum tank, white

46A 1131 Elbow, PVC

47 948B Motor, pump, DC out

48 FP361 PCB, pump motor speed, 120V

49 FP225 PCB, vacuum control

50 2B1 Screw, 6-32 X 2-1/4”

51 2014 Fan, cooling

51A 2015 Guard, fan

52 908A Latch, draw, rubber

53 928 Louver, 3”, includes 3 screws

54 BKCR-BLK Base, black

55 905 Castor, 4”

56 198 Hose clamp

58 FP348 Heat exchanger, complete

59 455 Bracket, mounting, heater

60 ---- See miscellaneous Parts and Kits

61 918 Plate, heat sink

62 FP348A Hose, heater to outlet

63 FP336 Snap track, PCB mounting, 4”

64 923B* PCB, circuit sensor

65 910-21.00 Axle, 21”

66 2084 Wheel, 10”

67 27A Axle cap

68 943B Switch plate

69 951B Pressure gauge

70 28 Screw, #4 X 3/8”

71 FP399 Potentiometer, with cable, pump

71A 248 Knob, blue top, for pump speed

72 78B Light, red, 120V

73 FP345 Switch & actuator, vacuum

74 FP346 Switch & actuator, bypass

75A 248 Knob, red top, for heat adjustment

75 FP347 Potentiometer, with wires, heat

76 78 Light, green

77 FP351 Gasket, (#1043A X 84”)

78 1128 Label, KC-500

81 FP350B Pressure line complete, 25’ with swivel

82 FP350A Vacuum hose complete, 25’ with swivel

83 2111 Terminal Block, for ground wires

84 2110 Circuit breaker, 15 amp

MISCELLANEOUS PARTS AND KITS

FP194E Heat repair kit includes probe, thermistor control,

thermal cutout

FP409 Pump & motor complete, w/unloader 500 psi

FP410 Pump complete w/unloader, no motor

950CP Pump rebuild kit, valves and O-rings, 500 psi

250 Pump rebuild kit, piston and seals, 300/500

FP350C Vacuum hose & pressure line, complete

FP350 Vacuum hose & pressure line with reel, complete

ITEM PARTNo DESCRIPTION ITEM PARTNo. DESCRIPTION

(NOTE: Items in kits not sold separately.)

Rotomolded Body:

Vacuum:

VAC Shutoff:

Pump:

Waterlift:

Heat:

Heater:

Wand:

Weight:

Lifetime Warranty

7.2” 3-stage

Electronic

Positive displacement, fully adjustable 0-500 psi

140”

Fully adjustable 145º to 212ºF

2000 Watts

Stainless steel, double bend, twin tip for 500 psi

122 lbs.

SPECIFICATIONS:

KING COBRA® 500-CSA

56380569

120V

425-322-0133 / 800-257-7982 / FAX: 425-322-0136

11015 - 47th Ave. W. / Mukilteo, WA 98275

VISIT US AT: http://www.usproducts.com

INFORMATION

DIRECTIVES

D’UTILISATION

04/24/2009

KING COBRA® 500-CSA

120 V

NE PAS UTILISER LA MACHINE AVANT D’AVOIR

LU TOUTES LES DIRECTIVESUN MAUVAIS USAGE

DE LA MACHINE ANNULERA LA GARANTIE

1. Toujours utiliser un agent antimousse quand il y a formation de mousse pour

empêcher d’endommager le moteur d’aspiration.

2. Protéger la machine de la pluie, de la neige et des températures extrêmes; la ranger

dans un endroit chauffé. Utiliser la machine à l’intérieur. Ne pas l’utiliser à l’extérieur.

3. Ne pas laisser la pompe fonctionner à sec.

4. Utiliser uniquement les produits chimiques autorisés. AUCUN SOLVANT.

5. Porter des gants ou utiliser des chiffons lorsque vous retirez les raccords à

démontage rapide pour éviter les brûlures.

IMPORTANTES CONSIGNES DE SÉCURITÉ

Cette machine convient uniquement à un usage commercial, par exemple dans les

hôtels, écoles, hôpitaux, usines, boutiques et bureau à d’autres fins qu’un entretien

ménager résidentiel normal.

Lors de l’utilisation de tout appareil électrique, il faut toujours prendre des précautions

élémentaires, y compris les suivantes :

NOTE : Lire toutes les consignes avant d’utiliser cette machine.

MISE EN GARDE!

Pour réduire le risque d’incendie, de choc électrique ou de blessures :

•Ne pas laisser la machine sans surveillance lorsqu’elle est branchée. Débrancher

l’appareil de la prise lorsqu’il ne sert pas et avant l’entretien courant.

•Pour éviter un choc électrique, ne pas exposer à la pluie ou à la neige. Ranger et

utiliser à l’intérieur.

•Ne pas s’en servir comme jouet. Il faut porter une attention particulière lors de son

utilisation près d’enfants.

•Utiliser uniquement comme il est décrit dans ce manuel. Utiliser uniquement les

accessoires recommandés par le fabricant.

•Ne jamais ajouter de l’eau à plus de 130º F/54º C dans le réservoir à solution.

•Ne pas utiliser avec un cordon ou une fiche endommagés. Si la machine ne

fonctionne pas comme elle le devrait, a été échappée, endommagée, laissée de-

hors ou échappée dans l’eau, la retourner à un centre de service.

•Ne pas tirer sur le cordon, utiliser le cordon comme une poignée, fermer un porte

sur le cordon ou enrouler le cordon autour de bords ou de coins acérés. Ne pas

faire passer la machine sur le cordon. Éloigner le cordon des surfaces chauffées.

Pour débrancher, tenir la fiche et non le cordon.

•Ne pas manipuler la fiche, le cordon ou la machine avec des mains mouillées.

•Les cordons prolongateurs doivent être du 12/3 et ne pas excéder 15 m (50 pi) de

longueur. Remplacer immédiatement le cordon ou la fiche si la broche de mise à la

terre est endommagée.

•Ne mettre aucun objet dans les ouvertures. Ne pas utiliser si une ouverture est

bloquée; préserver de la poussière, des peluches, des cheveux et de quoi que ce

soit qui réduirait le débit d’air.

•Tenir les vêtements lâches, les cheveux, les doigts et tout autre partie du corps loin

des ouvertures et des pièces mobiles.

•Ne pas ramasser quoi que ce soit qui brûle ou qui fume, comme des cigarettes,

allumettes ou cendres chaudes, ou des poussières dangereuses pour la santé. Ne

pas l’utiliser pour ramasser des liquides inflammables ou combustibles comme de

l’essence ou l’utiliser dans des aires où ils pourraient être présents

•Fermer toutes les commandes avant de débrancher.

•Faire particulièrement attention lors du nettoyage des escaliers.

•Brancher uniquement à une prise correctement mise à la terre.

•Le liquide projeté par la buse de pulvérisation pourrait être dangereux à cause de

sa température, de sa pression ou de son contenu chimique

Inhaltsverzeichnis

Sprachen:

Andere U.S. Products Schrubber Handbücher

U.S. Products

U.S. Products Solus 310R Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310R Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310 Betriebsanleitung

U.S. Products

U.S. Products HHP-150 Betriebsanleitung

U.S. Products

U.S. Products FLOODKING Betriebsanleitung

U.S. Products

U.S. Products KC-310 Betriebsanleitung

U.S. Products

U.S. Products Solus 500 Bedienungsanleitung

U.S. Products

U.S. Products ADVANTAGE 1200 Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-200H Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-200H Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310-CSA Betriebsanleitung

U.S. Products

U.S. Products COBRA-H2 Bedienungsanleitung

U.S. Products

U.S. Products HHP-300 Betriebsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

U.S. Products

U.S. Products COBRA PLUS-150 Betriebsanleitung

U.S. Products

U.S. Products PATRIOT B Betriebsanleitung

U.S. Products

U.S. Products MIRAI Bedienungsanleitung

U.S. Products

U.S. Products Cobra-H Bedienungsanleitung

U.S. Products

U.S. Products COBRA-C2 Bedienungsanleitung

U.S. Products

U.S. Products HP150-C Betriebsanleitung

U.S. Products

U.S. Products Solus 500R Betriebsanleitung

U.S. Products

U.S. Products KC 1200-500 Betriebsanleitung

U.S. Products

U.S. Products COBRA-H3-CE Betriebsanleitung

U.S. Products

U.S. Products MPE-400H Betriebsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung

Tennant

Tennant 7200 Bedienungsanleitung