U.S. Products MIRAI Bedienungsanleitung

56041968

MIRAI

EXTRACTOR

100V

INFORMATION

OPERATING

INSTRUCTIONS

1234

VAC1 VA C2 PUMPBYP

ASS

LOCATOR

MODE

5-2010

DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THESE INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. Keep machine from rain and snow, extremes in temperatures, and store in a

heated location. Use the machine indoors. Do not use outdoors.

3. Do not let the pump run dry.

4. Use approved chemicals only. NO SOLVENTS.

5. Wear gloves or use rags when removing quick disconnects to prevent burns.

6. Never use water above 54º C/130º F n the solution tank.

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops

and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet when not

in use and before servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only as described in this manual. Use only the manufacturer’s recommended attachments.

•Never add water over 130º F/54º C to the solution tank.

•Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped,

damaged, left outdoors or dropped into water, return it to a service center.

•Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp

edges or corners. Do not run the machine over the cord. Keep the cord away from heated surfaces.

To unplug, grasp the plug, not the cord.

•Do not handle the plug, the cord or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug immediately if

the ground prong becomes damaged.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair,

and anything that may reduce air flow.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or any

health endangering dusts. Do not use to pick up flammable or combustible liquids such as gasoline or

use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or

chemical content.

INSPECTION:

Carefully unpack and inspect your MIRAI for shipping damage. Each machine is tested and inspected

before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the

carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very

thoroughly they could cause a build-up in the pump, lines, heat exchanger and/or quick disconnects. Any

problem caused by a chemical build-up is not covered by warranty. Use a neutral cleaner with a pH

between 5 and 10 to avoid premature wear of the pump, seals, and/or other components. Damage

caused by the use of strong chemicals is not covered by the warranty.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day. Once a

month, minimum, run a flushing compound through the machine to break up any mineral or chemical

build-up that may have formed. The vacuum motor, pump motor, and the pump do not require any

scheduled maintenance; however, the motors may require replacement brushes after 1000 - 1500 hours,

and the pump and bypass valve may require rebuild kits after 1000 - 1500 hours, typically (refer to

machine part list for numbers). Clean the body with an all-purpose detergent, and protect it with an

automobile interior polish. Lubricate the wheels, castors, and quick disconnects with an all purpose

silicone spray.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an inventory

of original replacement parts and accessories. Call the distributor from whom you purchased this

machine if you need parts and service. Be sure to specify the machine model. Have your serial number

handy.

(and be sure to resister your purchase to activate your warranty)

Serial Number: __________________

Model: HHP-310-MIRAI

Purchase Date:_____________

Write the name and phone number of your distributor:

_____________________________________

SAVE THESE INSTRUCTIONS

VAC (1) & PUMP (2) SWITCHES:

These switches are powered by cord #1. The Vac and Pump switches will illuminate when

turned on.

PRESSURE SETTING SWITCH (3):

Changes pump pressure.

CORD 1 LIGHT (4):

This green light will turn on when Cord #1 is pluged in.

MODE LIGHT (5):

This light will only illuminate when the heater is heating and will turn off when it reaches

operating temperature. Note: this light will be on most of the time during normal operation.

1234

VAC1 VAC2 PUMP BYPASS

LOCATOR

MODE

HOLDING TANK LID

SWITCH PLATE LID (RECOVERY TANK)

VAC INTAKE

LATCH (2)

DRAIN GATE

CASTOR

VENT

PRIMING HOSE IN

POSITION FOR PRIMING

WHEEL

PRESSURE GAUGE

(ON REAR)

VAC PUMP 300 PSI

200 PSI CORD 1

MODE

123

SWITCH PLATE:

SET-UP and OPERATION:

1. Fill the holding tank with clear water and the detergent of your choice. Mix well.

Although this machine is designed to supply instant hot water, the addition of warm water (not

above 54º C/130º F) to the holding tank would increase heater efficiency.

2. Turn off all switches. Plug in cord #1 (vac and pump).

3. Attach the priming hose to the machine (see illustration on previous page). Turn on the pump and

select the 200 psi setting. Let the pump run until the pump is fully primed, then turn off the pump.

Remove the priming hose.

4. Connect the solution hose and vacuum recovery hose to the machine. Connect the hoses to the

cleaning tool.

2. Select either 200 or 300 psi. Turn on the pump and spray through the cleaning tool for only a few

seconds to fill the lines with solution. Turn the pump off.

3. Plug in cord #2 (identified by the red “H” on the back of te extractor). IF THE GREEN LIGHT

ILLUMINATES, THE HEAT EXCHANGER WILL TURN ON AUTOMATICALLY (SEE NOTE BELOW). Wait

2 minutes for the heat exchanger to reach operating temperature.

4. Begin cleaning.

5. When the job is finished, remove all unused solution, empty and clean the recovery tank, and clean

and dry the hoses and tools.

BALL FLOAT VAC SHUTOFF:

When the recovery tank is full, the float system will shut off the incoming air flow and prevent water from

entering the vacuum motors. The float may not work properly if the float ball cage is dirty or if there is

foam in the tank. Foam will not lift the ball float.

CAUTION: To avoid vac motor damage, always make sure the float cage is clean and the ball

travels freely before turning on the machine, and use a defoamer whenever foam is present.

4A 4B

61 62

41 43

28 33

66 65

86 85 84

103

100 101

102

11 10

12 13 14

51 53

27 26

26A 3232A

Priming Hose

26A

HHP-310

91 91

105

104

70A

76A

51A

107

108

56A

{

110

109

HP-310-KS

-R

100 V

7-30-2007

MIRAI

PARTS LIST

#1 FP231 Drain Gate, complete

#3 908 Latch

#4 187 O-Ring, Small

#4A 187B Washer, rubber

#4B 185 Nut, 1-1/2”

#5 V-1 Vacuum Tank, HHP, White

#6 907 Hose Barb, 1-1/2"

#7 922 PVC Elbow, 1-1/2"

#8 2009 Gasket (Vacuum Dome)

#9 FP201 Vacuum Dome

#10 FP193 Ball Float Assembly, Complete

#12 185 Nut, 1-1/2”

#13 187B Washer, rubber

#14 922 Elbow, PVC

#15 156 Hose Clamp

#16 FP171 Hose, Vacuum, Rubber

#17 76A Hose Clamp

#18 455 Mounting bracket, heater

#19 FP159G Heat Exchanger, Complete, 100V

#21 2012 Hose, 26”

#22 222 Quick Disconnect

#23 223 Quick Disconnect

#24 97 Bushing, Brass

#25 313 Hose Assy, braided, heater outlet

#26 31 Washer, brass

#26A 115 Washer, fiber

#27 92A Nipple, S/S, 1/4”

#28 116A Bushing, nylon

#29 92A Nipple, S/S, 1/4”

#38 926 Manifold, vacuum

#39 959 Gasket (Vacuum Motor)

#40 FP323 Vacuum Motor, 3-Stage, w/Connectors

#42 2015 Guard, fan

#44 2014 Fan, cooling

#45 459 Louver, 2-1/2” (includes screws)

#46 937 Reducer, PVC

#49 918 Heat Sink Plate

#50 FP194E Heat repair kit

#51 184 Cord Retainer

#51A 495A Power Cord, 25’, Yellow

#53 220 Quick Disconnect, Female, Open, 1/4 p.t.

#54 219 Quick Disconnect, Male, Open, 1/4 p.t.

#55 2164 Pressure Gauge, 2-1/2

#56 1005 Switch, rocker, for plug

#56A 340 Cord connector, three-prong

#57 341 Plate, for plug and switch

#58 2003 Wheel, 8”

#59 27A Axle Cap, Black

#60 969 Label, MIRAI

#62 180 Bracket, axle

#64 910-15.56 Axle rod

#65 928 Louver, 3”, includes screws

#66 FP228A Gasket, Base

#67 BY-1R Base, HHP, red

#68 905 Castor, swivel

#70 45 Quick Disconnect, Male

#70A SYP1 Priming Hose

#71 909A Latch Strike for Latch, S/S

#72 2010A Handle, Chrome

#74 FP204 Funnel, Black

#75 T-1 Holding Tank, HHP

#76 1557 Filter screen

#77 901 Lid, Holding Tank

#78 FP578 Switch, Pump & Vacuum

#80 968 Switch Plate

#81 78B Light, Red, Small

#83 78 Light, Green, Small

#86 166 Hose Clamp

#87 946 Hose, Pump Inlet, 1/2” X 14”

#88 FP236 Pump, complete, no motor or solenoid

#89 168 “T”, brass

#90 92A Nipple, S/S

#91 91 Elbow, Brass

#92 221 Quick Disconnect, Male, 0pen

#93 944 Hose, Pulsation Dampening

#94 FP477 Hose, with Swages

#95 211 Plug, Brass

#96 105 Reducer Nipple, Brass

#97 164 Hose Barb, brass

#98 945 Bypass Valve

#99 925 Hose, 3/8” X 8”

#100 208 Hose Barb, brass

#101 2062A Solenoid

#102 925 Hose, Pump Bypass, 3/8” X 14”

#103 2060 Motor, for pump

#104 CWBLK Cord Wrap, Black

#107 FP171B Hose, Exhaust, 2” x 12”

#108 928A Bracket, Exhaust Hose

MISCELLANEOUSASSEMBLIES/PARTS

291 Rebuild kit, bypass valve

250 Rebuild kit, pump plunger & seals

250CP Rebuild kit, pump Valve/O-Rings

950A Bearing/Cam Assembly (for Pump)

FP2008 Vacuum Dome, w/Gasket

(NOTE: Items in kits not sold separately.)

ITEM PART# DESCRIPTIONITEM PART# DESCRIPTION

SPECIFICATIONS:

Rotomolded Body:

Vacuum:

VAC Shutoff:

Pump:

Waterlift:

Heat:

Heater:

Wand:

Weight:

Dimensions:

Lifetime Warranty

7.2”, 3-stage

Ball float

Positive displacement, 300 psi for carpet and 75 psi for upolstery

140”

Adjustable to 212º F

1500 Watts

Stainless steel, double bend, twin tip

99 lbs.

26.5H x 18W x 28.75L (inches)

TROUBLE SHOOTING:

IF THIS OCCURS CHECK THIS

NO SPRAY

PUMP DOSEN’T RUN

Solution tank is empty.

Clogged spray tip.

Pump not running or not primed.

Valve on wand not operating.

Check the on/off switch an/dor the wires from the switch to the motor.

Debris plugging cleaning tool or vacuum hose.

Drain gate is not completely closed, or seals are damaged.

Vacuum dome is not seated or is damaged.

No power to motor. Test the switch. Test the Electronic Float. Test the

vacuum motor. Test the Vacuum Circuit Board.

Spraying too long. Try spraying for 12-15 seconds per cycle.

Heat exchanger needs to be flushed.

Wrong tool being used. Too much water passing through. Longer hose or larger

diameter hose, than standard

No power in the wall outlet - check to see if the breaker has tripped.

Check wiring for ‘opens.”

Call your distributor for additional help.

LOW SUCTION

NO SUCTION

LOW HEAT

NO HEAT

Inhaltsverzeichnis

Andere U.S. Products Schrubber Handbücher

U.S. Products

U.S. Products Cobra-H3 Bedienungsanleitung

U.S. Products

U.S. Products HHP-150 Betriebsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

U.S. Products

U.S. Products COBRA-H2 Bedienungsanleitung

U.S. Products

U.S. Products Solus 500 Bedienungsanleitung

U.S. Products

U.S. Products MPE-400H Betriebsanleitung

U.S. Products

U.S. Products KC 1200-500 Betriebsanleitung

U.S. Products

U.S. Products KC-310 Betriebsanleitung

U.S. Products

U.S. Products KING COBRA 1200 PRO Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-200H Betriebsanleitung

U.S. Products

U.S. Products KING COBRA 500-CSA Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-200H Betriebsanleitung

U.S. Products

U.S. Products FLOODKING Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-100H-SC Betriebsanleitung

U.S. Products

U.S. Products COBRA-H3-CE Betriebsanleitung

U.S. Products

U.S. Products COBRA PLUS-150 Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310R Betriebsanleitung

U.S. Products

U.S. Products Solus 500R Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310 Betriebsanleitung

U.S. Products

U.S. Products COBRA-C2 Bedienungsanleitung

U.S. Products

U.S. Products ADVANTAGE 1200 Betriebsanleitung

U.S. Products

U.S. Products PATRIOT B Betriebsanleitung

U.S. Products

U.S. Products Solus 310R Betriebsanleitung

U.S. Products

U.S. Products SOLUS-310-CSA Betriebsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung

Tennant

Tennant 7200 Bedienungsanleitung