Ubiquiti UniFi LED ULED-AT Bedienungsanleitung

LED

Network-Managed

LED Panel Powered by PoE+

Model: ULED-AT

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®LED

Panel. This Quick Start Guide is designed to guide you through

installation and includes warranty terms.

Package Contents

LED

Network-Managed

LED Panel Powered by PoE+

Model: ULED-AT

UniFi LED Panel Quick Start Guide

System Requirements

• An 802.3at-compliant network switch

• UniFi LED mobile app software

• Mobile device: iOS 10 or Android 5.0

• UniFi LED Controller software

• Computer: UniFi Application Server (UAS) 0.5.0,

Ubuntu 16.04 LTS (Xenial Xerus) 64-bit or Debian 9 64-bit

• Web browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Dimmer Switch, model UDIM-AT or UDIM-AC

Network Topology Requirements

There are three ways to control the UniFi LED Panel:

UniFi Dimmer Switch Users in the immediate vicinity control

the UniFi LED Panel using the UniFi Dimmer Switch.

UniFi LED App over Layer 2 Network A local user runs the

app to connect to a UniFi AP on the same Layer 2 network as

the UniFi LED Panel.

UniFi LED Controller over Layer 2 Network Alocal user runs

the LED Controller software on the same Layer 2 network as

the UniFi LED Panel.

UniFi PoE Switch

Internet

LAN

WAN

UAP-AC-PRO 802.3at PoE+

ULED-AT

UniFi Application Server

UniFi LED

Controller

UDIM-AT

UniFi LED

App

802.3af PoE

USG-PRO-4

(DHCP Server)

Sample Network Diagram

*640-00332-09*

640-00332-09

Network topology requirements are as follows:

• DHCP-enabled network (for the UniFi LED Panel to obtain

an IP address)

• For UniFi Dimmer Switch only:

A UniFi Dimmer Switch connected to the same Layer 2

network as the UniFi LED Panel

• For LED Controller software:

A UniFi Application Server running the UniFi LED Controller

software and connected to the same Layer 2 network as the

UniFi LED Panel

• For UniFi LED app only:

A UniFi AP connected to the same Layer 2 network as the

UniFi LED Panel

Hardware Overview

Status LED

LED

LED Color Status

Flashing White Initializing.

Steady White System ready.

Steady Blue Adopted by LED Controller.

Alternating

White/Blue Firmware upgrade is taking place.

ULED-AT-XXXXXX

Reset

PoE+

MAC

Sticker

Port

PoE+ The PoE+ port is a 10/100 Ethernet port used to connect

the power and should be connected to the LAN. Power is

provided by a UniFi Switch with 802.3at PoE+.

Note: The PoE+ port requires 25W of power, which can

be supplied by an 802.3at-compliant UniFi Switch.

MAC Sticker Used to scan the MAC address. For details, refer

to “Quick Setup”.

Button

Reset The Reset button serves two functions:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

Installation

To install and configure the UniFi LED Panel:

1. Connect one end of an Ethernet cable to the PoE+ port on

the back of the UniFi LED Panel.

2. Connect the other end of the cable to an 802.3at-compliant

switch port that can provide 25W PoE+.

3. Lift the panel and seat it in an opening in the ceiling grid.

Configuring the UniFi LED Panel

Follow the instructions for the software you wish to use:

UniFi LED App

1. Install the UniFi LED app on your smartphone or mobile

device. The app is available from the App Store® or

GooglePlay™Store.

2. Launch the app.

3. Follow the on-screen instructions to configure the UniFi

LED Panel.

UniFi LED Controller Software

1. Install the latest version of the UniFi LED Controller

software on a computer on the same Layer 2 network as

the UniFi LED Panel:

• Ubuntu users Download the software from

www.ubnt.com/download/unifi-led

• UAS users Install the software using the UAS

management console.

2. Launch a web browser and go to https://localhost:20443

3. The UniFi LED Controller will appear, allowing you to

configure the UniFi LED Panel, as well as customize other

settings.

For additional details on the UniFi LED Controller, refer to

the documentation at:

www.ubnt.com/download/unifi-led

Quick Setup

This section describes the Quick Setup procedure for

installations with large numbers of UniFi LED Panels and

Dimmer Switches. The Quick Setup requires using the UniFi

LED app along with a QR Code Log that you create. Each UniFi

LED Panel or Dimmer Switch has a removable MAC Sticker on

its reverse side; this has a QR code used to scan the device’s

MAC address. The Quick Setup consists of these steps:

• Create the QR Code Log

• Install the LED Panels and Dimmer Switches

• Scan the QR codes

Create the QR Code Log

1. Download the QR Code Log template at:

ubnt.link/QR-Code-Log

2. Print out as many copies as needed (each sheet can log up

to 16 LED Panels and 3Dimmer Switches).

Site:

Controller:

QR Code Log

UDIM-AT-XXXXXX

arrows and place them on this QR Code Log.

3. Fill in the Site (such as “1st Floor Meeting Room”) and

Controller (such as “UniFi LED Controller”) on each sheet.

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti U6-MESH Bedienungsanleitung

Ubiquiti

Ubiquiti ES-10X Bedienungsanleitung

Ubiquiti

Ubiquiti mPort-S mPort Serial Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP Bedienungsanleitung

Ubiquiti

Ubiquiti 0810354025402 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-OLT-4 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwtch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber OLT Bedienungsanleitung

Ubiquiti

Ubiquiti USW-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti U-Installer Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung