Ubiquiti PBM3 Bedienungsanleitung

Carrier-Class

airMAX®BaseStation

Models:

PBM3, PBM365, PBM5

Introduction

Thank you for purchasing the Ubiquiti Networks™

PowerBridge™M. This Quick Start Guide is designed to guide

you through the installation, and show you how to access the

airOS® Configuration Interface. This Quick Start Guide also

includes the warranty terms and is for use with the following

models:

Model Operating Frequency

PowerBridgeM3 3300 - 3700 MHz

PowerBridgeM365 3650 - 3675 MHz

PowerBridgeM5 Worldwide: 5170 - 5875 MHz

USA: 5745 - 5850 MHz

Package Contents

PowerBridgeM Pole Brackets

(Qty. 2)

Pole Clamps

(Qty. 2)

Carriage Bolts

(M8X135,

Qty. 4)

Carrier-Class

airMAX™BaseStation

Models:

PBM3, PBM365, PBM5

Flange Bolts

(M8X20,

Qty. 4)

Flange Nuts

(M8, Qty. 4)

PoE Adapter

(24V, 1A)

Power Cord Quick

Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Ports

Ethernet Port

(10/100) Mbps

Reset

Button

Port Cover U-Brackets

Ethernet Port The Ethernet port is a 10/100 Mbps port used

for data and supplies power to the PowerBridgeM. Power can

be provided by any of the following:

• PoE adapter (included)

• Ubiquiti Networks TOUGHSwitch™PoE

• Ubiquiti Networks EdgeRouter™PoE

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the

PowerBridgeM is already poweredon.

LEDs

Power The Power LED will light green when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light red when the wireless signal

strength is above -94 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light green when the wireless signal

strength is above -65 dBm.

Installation Requirements

• 13 mm or ½" wrench

• Flathead screwdriver

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Installation

To install the PowerBridgeM, perform the following steps:

1. The Port Cover is hinged to the PowerBridgeM and locked

with a screw. Use a flathead screwdriver to turn the locking

screw counter-clockwise until it is loose. Open the cover by

sliding it down and raising it up.

*720-00065-02*

720-00065-02

2. Connect an Ethernet cable to the Ethernet Port.

3. Close the Port Cover and lock it in place by turning the

locking screw clockwise.

4. Insert two Carriage Bolts into each Pole Bracket.

5. Connect the Pole Brackets to the U-Brackets using the four

Flange Bolts.

6. Mount the PowerBridgeM to the pole:

a. Position the Carriage Bolts around the pole at the

mounting location.

b. Slide a Pole Clamp onto each pair of Carriage Bolts.

c. Hand-tighten a Flange Nut on each Carriage Bolt.

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

7. Rotate the PowerBridgeM to the correct azimuth towards

the other end of the wireless link.

8. Adjust the elevation angle as needed:

a. Loosen the four Flange Bolts on the U-Brackets.

b. Adjust the PowerBridgeM to the desired elevation tilt.

c. Tighten all bolts and nuts to approximately

25 N-m (18 lb-ft).

Flange

Bolts

Powering the PowerBridgeM

The PowerBridgeM can be powered by the included PoE

Adapter or any of the following compatible PoE switches:

• TOUGHSwitch PoE, model TS-5-POE

• TOUGHSwitch PoE PRO, model TS-8-PRO

• EdgeRouter PoE, model ERPoe-5

Connecting to the PoE Adapter

1. Connect the other end of the Ethernet cable from the

PowerBridgeM to the Ethernet port labeled POE on the

PoEAdapter.

2. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the PoE Adapter.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti NS-5AC Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber 60 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC Gen 2 Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam M5-23 Bedienungsanleitung

Ubiquiti

Ubiquiti AM-5AC21-60 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M5 PBE-M5-400 Bedienungsanleitung

Ubiquiti

Ubiquiti U6-MESH Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-23 Bedienungsanleitung

Ubiquiti

Ubiquiti RocketDish RD-5G30 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-300-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti Airmax NBE-M2-400 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Bedienungsanleitung

Ubiquiti

Ubiquiti airVision-C Bedienungsanleitung

Ubiquiti

Ubiquiti UF-LOCO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M5 Handbuch

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung