Ubiquiti EdgeSwitch 16 XG Bedienungsanleitung

10G 16-Port Managed

Aggregation Switch

Model: ES-16-XG

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch™

XG. This Quick Start Guide is designed to guide you through

installation and also includes warranty terms.

Package Contents

EdgeSwitch XG

Power Cord Rack-Mount Brackets

(Qty. 2)

Bracket Screws

(M4, Qty. 8)

10G16-Port Managed

AggregationSwitch

Model:ES-16-XG

Mounting Screws

(#10-32 x 5/8", Qty. 4)

Cage Nuts

(#10-32 x 5/8", Qty. 4)

Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Installation Requirements

• Phillips screwdriver (for rack- or wall-mounting)

• Standard-sized, 19" wide rack with a minimum of 1U height

available (for rack-mounting)

• Use compatible fiber SFP+ modules with the appropriate

fiber optic cabling. For information about compatible fiber

SFP+ modules, visit: community.ubnt.com/edgemax

• For indoor applications, use Category 6A (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 6A (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the switch to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeSwitch XG itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

SFP+ 1-12 RJ45 13-16

Port Description

SFP+ 1-12 Hot-swappable SFP+ ports support 1 Gbps

and 10 Gbps connections.

RJ45 13-16 RJ45 ports support 1 Gbps and 10 Gbps

Ethernet connections.

Front Panel LEDs

System SFP+: Speed/Link/Act RJ45: Speed/Link/Act

LED State Status

System

White Ready for Use

Blue

Bootup in Progress

Flashing Indicates Reset to

Factory Defaults

SFP+ 1-12

Speed/

Link/

Act

Off No Link

Green Link Established at 1Gbps

Flashing Indicates Activity

White Link Established at 10Gbps

Flashing Indicates Activity

RJ45 13-16

Speed/

Link/

Act

Off No Link

Green Link Established at 1Gbps

Flashing Indicates Activity

White Link Established at 10Gbps

Flashing Indicates Activity

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeSwitch XG to factory defaults:

Runtime Reset (Recommended)

The EdgeSwitch XG should be running

after bootup is complete, and the System

LED is white. Press and hold the Reset

button. The EdgeSwitch XG will reboot, and

the System LED becomesblue after three

seconds. Continue to hold the Reset button

for about 15seconds until the System LED

flashes blue for two seconds. This indicates

that the EdgeSwitch XG has reset to its

factorydefaults.

Power-on Reset

1. Disconnect the power from the

EdgeSwitch XG.

2. While connecting the power to the

EdgeSwitch XG, hold the Reset button

for about 15seconds until the System

LED flashes blue for two seconds. This

indicates that the EdgeSwitch XG has

reset to its factory defaults.

Back Panel Console Port

Console

Port Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect

the Console port to your computer. Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

*640-00227-03*

640-00227-03

Back Panel Power

Power

DC Input

DC Input The 25VDC input can connect a redundant or

stand-alone DC power source (not included) with minimum

power: 56W, 25 to 16V, and 2.5 mm DC power inline connector.

Note: You can use the redundant DC power source as a

hot spare; if the internal AC/DC power supply no longer

provides power, then the EdgeSwitch XG will switch to

the DC power source without interrupting its operation.

Power Connect the included Power Cord to the Power port.

Side Panel

Ventilation

Holes

Bracket Mounting

Holes

Hardware Installation

The EdgeSwitch XG can be placed on a horizontal surface,

mounted on a wall, or mounted in a rack.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Mounting in a Rack (Optional)

1. Attach the Rack-Mount Brackets to the EdgeSwitch XG

using the eight Bracket Screws.

2. Attach the EdgeSwitch XG to the rack or wall using the four

Mounting Screws. (If the rack has square slots, then use the

Cage Nuts with the Mounting Screws.)

Connecting Power

1. Connect the Power Cord to the Power port of the

EdgeSwitch XG.

2. Connect the other end of the Power Cord to a power outlet.

Connecting SFP+

1. Remove the protective plug covering the SFP+ port.

2. Plug a compatible fiber module into the SFP+ port.

1000MbpsSM/SC20KMDDM

Tx1550nm/Rx1310nm

3. Connect the fiber optic cable to the fiber module. Then

connect the other end of the cable to another fiber device.

4. Repeat steps 1-3 to connect additional SFP+ ports.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Schalten Handbücher

Ubiquiti

Ubiquiti UniFi USW-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti 0810354023262 Bedienungsanleitung

Ubiquiti

Ubiquiti unifi switch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 24 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-16-CARRIER Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti ES-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch ES-10XP Leitfaden

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti USW--Pro--48 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti USW-Pro-24 Bedienungsanleitung

Ubiquiti

Ubiquiti US-24 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti POE-50-60W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti US-24 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch