Ubiquiti ES-24-250W Bedienungsanleitung

Managed PoE+ Gigabit Switch

with SFP

Models: ES-24-250W, ES-24-500W

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch™.

This Quick Start Guide is designed to guide you through the

installation and show you how to access the Configuration

Interface. This Quick Start Guide also includes the warranty

terms, and is for use with the EdgeSwitch, modelES‑24‑250W

or ES‑24‑500W. (The hardware description and installation

instructions are the same for both models.)

Package Contents

24V

EdgeSwitch

Managed PoE+ Gigabit Switch

with SFP

Models: ES-24-250W, ES-24-500W

Power Cord Mounting Screws

(#10‑32 x 5/8", Qty. 4)

Cage Nuts

(#10‑32 x 5/8", Qty. 4)

Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Standard‑sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks

from the most brutal environments and devastating ESD

attacks with industrial‑grade shielded Ethernet cable,

TOUGHCable™, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the EdgeSwitch itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel LEDs

System

RJ45: PoE RJ45: Speed/Link/Act

SFP: Speed/Link/Act

LED State Status

System

White Ready for Use

Blue

Bootup in Progress

Flashing Indicates Reset

to Factory Defaults

RJ45 1‑24

PoE

Off No PoE

Amber IEEE 802.3af/802.3at

Green 24V Passive

Speed/

Link/

Act

Off No Link

Amber

Link Established at

10/100Mbps

Flashing Indicates Activity

Green

Link Established at

1000Mbps

Flashing Indicates Activity

SFP 1‑2

Speed/

Link/

Act

Off No Link

Green Link Established at 1Gbps

Flashing Indicates Activity

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeSwitch to factory defaults:

Runtime Reset (Recommended)

The EdgeSwitch should be running after

bootup is complete, and the System LED

is white. Press and hold the Reset button.

The EdgeSwitch will reboot, and the System

LED becomesblue after three seconds.

Continue to hold the Reset button for

about 15seconds until the System LED

flashes blue for two seconds. This indicates

that the EdgeSwitch has reset to its

factorydefaults.

Power‑on Reset

1. Disconnect the Power Cord from the

EdgeSwitch.

2. While connecting the Power Cord to

the EdgeSwitch, hold the Reset button

for about 15seconds until the System

LED flashes blue for two seconds. This

indicates that the EdgeSwitch has reset

to its factory defaults.

Front Panel Ports

RJ45 1-24 SFP 1-2

Interface Description

RJ45 1‑24 RJ45 ports support Power over Ethernet

(PoE) and 10/100/1000 Ethernet connections.

SFP 1‑2 Hot‑swappable SFP ports support 1 Gbps

connections.

Back Panel

Mounting Holes

Power

Mounting Holes

Side Panels

Ventilation Holes

Fans

*640-00102-04*

640-00102-04

Hardware Installation

1. Connect the Power Cord to the Power port of the

EdgeSwitch.

2. Attach the EdgeSwitch to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts

with the Mounting Screws.)

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.

3. Connect the other end of the Power Cord to a power outlet.

Connecting Ethernet

1. Connect an Ethernet cable from your computer or host

system to any port of the EdgeSwitch.

2. Connect Ethernet cables from the Ethernet ports of your

devices to the numbered ports of the EdgeSwitch.

Note: The PoE settings for ports 1-24 are set to

PoE+auto by default, so 802.3af/at devices can

be plugged in and automatically receive PoE. For

instructions on how to enable 24V passive PoE,

refer to the Configuring PoE Settings section on the

backpage.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a compatible fiber module into the SFP port.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

3. Connect the fiber optic cable to the fiber module. Then

connect the other end of the cable to another fiber device.

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

Accessing the Configuration Interface

The EdgeSwitch is set to DHCP by default, so it will try to

automatically obtain an IP address. If that fails, then it will use

the default fallback IP address, 192.168.1.2. Proceed to the

appropriate section, DHCP or Fallback IP Address:

DHCP

Use one of the following methods:

• Set up the DHCP server to provide a specific IP address to

the EdgeSwitch based on its MAC address (on the label).

• Let the EdgeSwitch obtain an IP address and then check the

DHCP server to see which IP address was assigned.

To log in, follow these steps:

1. Launch your web browser. Type the appropriate IP address

in the address field. Press enter (PC) or return (Mac).

2. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeSwitch Configuration Interface will appear. Customize

additional settings as needed. For more information on PoE

configuration, refer to the Configuring PoE Settings section on

the back page.

Andere Handbücher für ES-24-250W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Schalten Handbücher

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti ETHERMAGIC EM-S Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti unifi switch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti TS-16-CARRIER Bedienungsanleitung

Ubiquiti

Ubiquiti UA-Hub Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti UnFi US-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti ES-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 48 Bedienungsanleitung

Ubiquiti

Ubiquiti ES-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 24 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-16-CARRIER Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 24 US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch Bedienungsanleitung

Ubiquiti

Ubiquiti 0810354023262 Bedienungsanleitung

Ubiquiti

Ubiquiti US-24 Bedienungsanleitung

Ubiquiti

Ubiquiti USW--Pro--48 Bedienungsanleitung

Ubiquiti

Ubiquiti TouchSwitch Poe TS-5-POE Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch