Ubiquiti TouchSwitch Poe TS-5-POE Bedienungsanleitung

5-Port Power over Ethernet

Managed Switch

Model: TS-5-POE

Introduction

Thank you for purchasing the Ubiquiti Networks 5-Port

TOUGHSwitch™PoE, model TS-5-POE. It is part of the

TOUGHSwitch series:

Name Model Description

5-Port TOUGHSwitch PoE TS-5-POE Managed switch

featuring 24V PoE

8-Port TOUGHSwitch PoE PRO TS-8-PRO Managed switch

featuring 24V or 48V PoE

TOUGHSwitch PoE Carrier TS-16-Carrier Two 8-Port

TOUGHSwitch PoE PROs

mounted in a rack

For more information, visit www.ubnt.com.

This Quick Start Guide is designed to guide you through the

installation of the TOUGHSwitch and show you how to access the

Configuration Interface.

Package Contents

5-Port TOUGHSwitch PoE M2.9x20 Screws

(Qty. 2)

M2.9 Anchors

(Qty. 2)

Carrier Class

5-Port TOUGHSwitch PoE

Model: TOUGHSwitch-5-POE

Quick Start Guide Power Adapter

(24V, 2.5A)

Power Cord

5-Port TOUGHSwitch™PoE Quick Start Guide

Hardware

Back Panel

Power

Grounding

Slot

Grounding

Slot

Ventilation Holes

Front Panel Ports

Management

USB Reset

1-5

Interface Description

Management

10/100 Mbps port for management. Traffic between

the Management port and numbered ports will

be limited to 10/100 Mbps and, under heavy

load, may cause performance degradation of the

TOUGHSwitch.

USB Reserved for future use.

1-5 10/100/1000 Mbps ports for switching and PoE (also

available for management by default).

Reset

To reset to factory defaults, press and hold the Reset

button for more than five seconds while the unit is

already powered on.

Hardware

Front Panel LEDs

Link/Act

PoE

Speed/Link/Act

LED State Status

Management

Link/Act

Off No Link

Amber

After bootup, the LED indicates

power. After an initial link is

established, the LED indicates a

10/100 Mbps connection. If the

link terminates, the LED turns

off until a link is re-established.

If the unit reboots, the LED will

again indicate power until a link is

established.

Amber Flashing Activity

1-5

PoE

Off No Power over Ethernet

Green 24V Power over Ethernet

Speed/

Link/Act

Off No Link

Amber Link Established at 10/100 Mbps

Amber Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps

Green Flashing Link Activity at 1000 Mbps

5-Port TOUGHSwitch™PoE Quick Start Guide

Hardware Installation

Mount the TOUGHSwitch on a wall or place it on a bench top.

Note: Keep 20 mm of clearance next to the ventilation

holes for adequate airflow.

Wall-Mounting

Installation Requirements

• Drill and 6 mm drill bit

• Phillips screwdriver

Instructions

To mount the TOUGHSwitch on a wall:

1. Use a 6 mm drill bit to drill two holes 60 mm apart.

2. Insert the M2.9 Anchors into the holes.

3. Use a Phillips screwdriver to secure a M2.9x20 Screw to each

anchor. Leave a clearance of approximately 3 mm between

each screw head and its anchor.

60 mm

3 mm

Note: You can also mount the TOUGHSwitch in a

horizontal orientation.

Hardware Installation

4. Position the Wall-Mount Slots of the TOUGHSwitch over the

screw heads on the wall. Then slide the TOUGHSwitch to the

left to lock it into place.

Grounding the TOUGHSwitch (Optional)

The TOUGHSwitch is grounded through the Power Adapter;

however, you can add optional ESD grounding for enhanced ESD

protection.

1. Insert a ground wire (not included) through a corner slot.

2. Twist tie to secure the ground wire to the TOUGHSwitch.

3. Secure the other end of the ground wire to a grounding block.

5-Port TOUGHSwitch™PoE Quick Start Guide

Connecting Power

1. Connect the power connector of the Power Adapter to the

Power port of the TOUGHSwitch.

2. Connect the Power Cord to the power port on the Power

Adapter. Connect the other end of the Power Cord to a power

outlet.

Hardware Installation

Connecting Ethernet

1. Connect an Ethernet cable from the Ethernet port of your

computer to the Management port of the TOUGHSwitch.

2. Connect Ethernet cables from the Ethernet ports of your

devices to the numbered ports of the TOUGHSwitch.

Note: PoE is disabled by default on all numbered ports

and is not available on the Management port. To enable

PoE on the appropriate ports, use the Ports tab in the

Configuration Interface.

5-Port TOUGHSwitch™PoE Quick Start Guide

Accessing the Configuration Interface

Connect to the Configuration Interface by performing the

following steps:

1. Ensure that your computer (or other host machine) is

connected to the Management port on the TOUGHSwitch.

Note: By default, you can configure the TOUGHSwitch

via any port; however, we recommend the Management

port. (Access to the Configuration Interface can be

limited to the Management port only. You can configure

this setting on the Device tab.)

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).

3. Launch your web browser. Type https://192.168.1.20 in the

address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username and

Password fields. Click Login.

The Configuration Interface will appear, allowing you to customize

your settings as needed. You can enable PoE on the Ports tab.

Refer to the TOUGHSwitch PoE User Guide for instructions on

configuring the TOUGHSwitch. The User Guide is available at

documentation.ubnt.com

Inhaltsverzeichnis

Andere Ubiquiti Schalten Handbücher

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti ES-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 150W Bedienungsanleitung

Ubiquiti

Ubiquiti USW-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 12 Fiber Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-16-POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti UBNT-US-8-150W-US Bedienungsanleitung

Ubiquiti

Ubiquiti FiberPoE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-500W Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch