Ubiquiti NBE--2AC--13 Bedienungsanleitung
2.4 GHz, 13 dBi
airMAX®ac CPE
Model: NBE-2AC-13
Introduction
Thank you for purchasing the Ubiquiti Networks®
NanoBeam®ac. This Quick Start Guide is designed to guide
you through installation and also includes warranty terms.
Package Contents
NanoBeam Ball Joint
Mount
Lock Ring
2.4GHz, 13 dBi
airMAX®acCPE
Model:NBE-2AC-13
Metal Strap Gigabit PoE Adapter
with Mounting Bracket
Power Cord Quick Start
Guide
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is
designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
Installation Requirements
The NanoBeam can be mounted on a pole or to a wall. A Metal
Strap (included) is used for pole-mounting. For wall-mounting,
a suitable fastener such as a screw or bolt (not included) is
required.
• Pole-mounting: 7 mm socket wrench or screwdriver
• Wall-mounting: wall fastener (not included)
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.
We recommend that you protect your networks from the
most brutal environments and devastating ESD attacks with
industrial-grade shielded Ethernet cable, TOUGHCable from
Ubiquiti Networks.
For more details, visit www.ubnt.com/toughcable
Hardware Overview
This device c omplies with Pa rt 15 of FCC rules.
Operation is subject to the following 2 conditions:
1) this device may not cause harmful interference
and, 2) this device must accept any interference
received, inclu ding interferenc e that may cause
undesiredoperation.
FCCID: SWX-NBE2AC13
IC: 6545A-NBE2AC13
M/N:NBE-2AC-13
24V 0.5AGigE PoE
Compliant
RoHS
LEDs
Reset Button Ethernet Port
(10/100/1000 Mbps)
Reset Button To reset to factory defaults, press and hold the
Reset button for more than 10 seconds while the NanoBeam
is already poweredon. Alternatively, the NanoBeam may be
reset remotely via a Reset button located on the bottom of the
Gigabit PoE Adapter.
Ethernet Port This Gigabit Ethernet port is used to connect
the power and should be connected to the LAN and DHCP
server. Power can be provided by any of the following:
• Gigabit PoE Adapter (included)
• Ubiquiti Networks EdgeSwitch™
• Ubiquiti Networks EdgeRouter™ PoE
LEDs
Power The Power LED will light blue when the
device is connected to a power source.
Ethernet The Ethernet LED will light steady blue
when an active Ethernet connection is made and
flash when there is activity.
Signal The default values are shown below:
LED will light blue when the wireless signal
strength is equal to or above -94 dBm.
LED will light blue when the wireless signal
strength is equal to or above -80 dBm.
LED will light blue when the wireless signal
strength is equal to or above -73 dBm.
LED will light blue when the wireless signal
strength is equal to or above -65 dBm.
Hardware Installation
The NanoBeam can be mounted on a pole or to a wall. Perform
the steps for the appropriate installation:
Pole-Mount
1. Insert the Ball Joint Mount into the Lock Ring with the
threads of the Lock Ring facing the ball joint.
2. Open the Metal Strap and feed it through the base of the
Ball Joint Mount.
3. Wrap the Metal Strap around the pole. Use a 7 mm socket
wrench to turn the screw clockwise and securely fasten the
clamp to the pole.
4. Attach the NanoBeam to the Ball Joint Mount and turn the
Lock Ring to secure it. Keep the Lock Ring loose enough to
allow the NanoBeam to pivot for aiming.
Wall-Mount
The NanoBeam must be mounted directly to a wood stud
or other structurally stable surface to avoid damage to the
mounting hole when you adjust the aim.
Optional Accessory
To enhance stability, you can use the NanoBeam Wall Mount
Kit, model NBE-WMK (soldseparately).
Note: Center screw included. Two optional screws
(not included) provide additional stability.
Installation Instructions
1. Mark the desired location of the mounting point.
2. If needed, drill a pilot hole for the fastener (not included).
3. Insert the Ball Joint Mount into the Lock Ring with the
threads of the Lock Ring facing the ball joint.
4. If you are using the optional NanoBeam Wall Mount Kit,
then skip to step b.
a. To attach the Ball Joint Mount to the wall, insert a
fastener (not included) through the center of the ball
joint, and into the wall. Securely tighten the fastener.
Proceed to step 5.
b. To attach the Ball Joint Mount to the wall, insert the Wall
Mount Kit screw through the center of the ball joint,
through the Wall Mount Kit plate, and into the wall.
Securely tighten the screw.
5. Attach the NanoBeam to the Ball Joint Mount and turn the
Lock Ring to secure it. Keep the Lock Ring loose enough to
allow the NanoBeam to pivot for aiming.
Aiming
1. Ensure the opening of the Ethernet cable is pointed
towards the ground.
2. Aim the front of the NanoBeam towards the other end of
the wireless link.
3. Hand-tighten the Lock Ring to lock the aim.
Note: Do not use a tool to tighten the Lock Ring.
Tighten the Lock Ring by hand only.
Connecting to the PoE Adapter
1. Remove the port cover by pressing down the center of the
cover and sliding the cover out.
2. Connect an Ethernet cable to the Ethernet port.
This device com plies with Par t 15o f FCC rules.
Operation is subject to the following 2 conditions:
1)this device may not cause har mful interference
and, 2) this device must accept any interference
received, includin g interference th at may cause
undesiredoperation.
FCCID: SWX-NBE2AC13
IC:6545A-NBE2AC13
M/N:NBE-2AC-13
24V 0.5AGigE PoE
Compliant
RoHS
3. Replace the port cover.
Andere Handbücher für NBE--2AC--13
2
Inhaltsverzeichnis
Andere Ubiquiti Drahtloser Zugangspunkt Handbücher
Ubiquiti
Ubiquiti M5 GPS Rocket M Series Bedienungsanleitung
Ubiquiti
Ubiquiti PowerBeam PBE-5AC-Omni Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi AC Mesh Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi Bedienungsanleitung
Ubiquiti
Ubiquiti BulletAC-IP67 Bedienungsanleitung
Ubiquiti
Ubiquiti UAP-PRO UNIFI Bedienungsanleitung
Ubiquiti
Ubiquiti IsoStation AC Bedienungsanleitung
Ubiquiti
Ubiquiti UAP-Outdoor Bedienungsanleitung
Ubiquiti
Ubiquiti LAP-GPS Bedienungsanleitung
Ubiquiti
Ubiquiti Rocket R5AC-Lite Bedienungsanleitung
Ubiquiti
Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung
Ubiquiti
Ubiquiti Loco5AC Bedienungsanleitung
Ubiquiti
Ubiquiti BulletM2-HP Bedienungsanleitung
Ubiquiti
Ubiquiti PBE-M5-300-US Bedienungsanleitung
Ubiquiti
Ubiquiti BULLETM2-HP-US Bedienungsanleitung
Ubiquiti
Ubiquiti PowerBeam ac ISO Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi Dream Machine Beacon Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation M2 Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi AP-AC PRO Bedienungsanleitung
Ubiquiti
Ubiquiti UF-Nano Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
