Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Andere Handbücher für PowerBeam AC PBE-5AC-620

3

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation5 Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti RP5AC-PRISM Bedienungsanleitung

Ubiquiti

Ubiquiti PrismStation 5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStationXG UWB-XG-BK Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M2 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam m5 iso PBE-M5-300-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-24HD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi XG Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti NanoStation M2 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-5XHD Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC EDU Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC MESH PRO Bedienungsanleitung

Ubiquiti

Ubiquiti AirCube ACB-AC Bedienungsanleitung

Ubiquiti

Ubiquiti UAP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung

Clamp Screws (qty: 4)

Package content

Hex Head Cap Screws (Qty:

5)

Upper Post Bracket

Assembly

Parabolic reflector with

mounting bracket

lock washers

lower post bracket

Back case

Flat washers (cant.: 5)

power horn

stabilizer mounts

support arm

PBE-5AC-620 Quick Start Guide

installation requirements

Power cord

(cant.: 2)

M10x100 screws (qty: 2) M10 flange nuts (qty: 2)

(cant.: 5)

M8 flange nuts (Qty: 4) Foot clamp (Qty: 2) Gigabit PoE (24V, 0.5A) with mounting bracket

We recommend that you protect your networks from harmful outdoor environments and

electrostatic discharge phenomena with Ubiquiti's Industrial Grade Shielded Ethernet Cable.

For more information, visit ui.com/toughcable

Round head screws M8x150

(qty: 4)

13mm wrench

Category 5 (or higher) shielded cabling must be used for all Ethernet connections

and must be connected to the AC ground of the PoE.

Phillips screwdriver

16mm wrench

hardware description

Ethernet

reset button

Luces LED

bottom view

release button

After mounting the PowerBeam, check the release button; it should be fully

engaged in the button hole on the back cover. In this way, you will ensure that

the power horn is well located and fixed. If you need to remove the power

horn, please press the release button first.

To restore factory defaults, press and hold the reset button for more than 10

seconds while the device is turned on. You can also remotely reset the device

using the reset button on the bottom of the Gigabit PoE adapter.

The Gigabit Ethernet port is used to connect power and must be

connected to the LAN and DHCP server.

Sign

Ethernet

Application Examples

On airOS®, you can modify the wireless LED signal strength threshold value in the Wireless

tab, under Signal LED Thresholds. Each LED will turn on when the wireless signal strength is

equal to or greater than the threshold value set for the LED indicator. The default threshold

values for these LED indicators are listed below:

Feeding

The LED indicator will light blue when the device is connected to a power source.

The LED indicator will turn solid blue when the device is connected to an Ethernet

network and will blink if there is activity.

Outdoor mounted PowerBeam with reflector installed provides directional

outdoor coverage (gain dependent on reflector).

The exterior mounted PowerBeam without the reflector installed provides exterior to

interior coverage only through the 3 dBi feed horn.

1.

Installation

2.

3.

4.

5.

6.

7.