UBX UBR510B Bedienungsanleitung
Model. UBR510B
INSTRUCTION
MANUAL
5.1CH Surround AV Amplier Package
with 3D HDMI and Bluetooth
Switchable Dual Voltage : 115V or 230V(Preset to 230V)
Please make sure to set a right voltage before power on!
NOTICE
Software
&
Hardware Upgrade!
NEW
2
4
5
9
12
Safety Information
Safety Precautions
Some Do’s and Don’ts On The Safe Use Of Equipment
Introduction
Features
Accessory List
Panel and Remote Operation
Front and Back Panel
Remote Control
Input Modes
Switching Input Modes
Reference
Troubleshooting
Specications
TABLE OF CONTENTS
SAFETY INFORMATION
Safety Precautions
To achieve the utmost in enjoyment and performance, and in order to become familiar with its
features, please read this manual carefully before attempting to operate this product, this will
assure you years of trouble free performance and listening pleasure.
Important Notes
This safety and operating instruction should be retained for future reference.
The apparatus should not be exposed to dripping or splashing or placed in a humid
atmosphere such as a bathroom
Do not install the product in the following areas:
o Places exposed to direct sunlight or close to radiators
o On top of other stereo equipment that radiate too much heat
o Blocking ventilation or in a dusty area
o Areas where there is constant vibration
o Humid or moist places.
Do not place near candles or other naked ames
Operate the product only as instructed in this manual
Before turning on the power for the rst time, make sure the power adaptor is properly
connected.
For safety reasons, do not remove any covers or attempt to gain access to the inside of the
product. Refer any servicing to qualied personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user
serviceable parts inside, refer all servicing to qualied service personnel.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
DANGEROUS VOLTAGE
Dangerous Voltages that may be of sucient magnitude to constitute a risk of
electric shock to persons are present within this product’s enclosure.x
ATTENTION
The owner’s manual contains important operating and maintenance instructions,
for your safety, it is necessary to refer to the manual.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
DRIPPING OR SPLASHING.
Note : This unit will become warm when used for a long period of time. This is normal and does not
indicate a problem with the unit.
2
Some Do’s and Don’ts on the Safe Use of Equipment
SAFETY INFORMATION
This equipment has been designed and manufactured to meet international safety standards but, like
any electrical equipment, care must be taken if you are to obtain the best results and safety is to be
assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections
between the pieces of equipment) are properly made and in accordance with the manufacturer’s instructions.
Switch o and unplug the power before making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DON’T remove any xed cover as this may expose dangerous voltages.
Overheating will cause damage and shorten the life of the equipment.
DON’T allow electrical equipment to be exposed to dripping or splashing, or objects lled with liquids, such as
vases, to be placed on/near the equipment.
DON’T place hot objects or naked ame sources such as lighted candles or nightlights on, or close to equipment.
High temperatures can melt plastic and lead to res.
DON’Tuse equipment such as personal stereos or radios so that you are distracted from the requirements
of trac safety.
DON’T leave equipment switched on when it is unattended unless it is specically stated that it is designed for
unattended operation. Switch o using the switch on the equipment and make sure that your family knows
how to do this. Special arrangements may need to be made for inrm or handicapped people.
DON’T continue to operate the equipment if you are in any doubt about if it’s working normally or if it’s
damaged in any way. Switch it o, unplug the mains power and consult your dealer.
ESD Remark : In case of malfunction due to electrostatic discharge just reset the product
(reconnection of mains power may be required) to resume normal operation.
3
INTRODUCTION
Features
Accessory List
AAA Battery x2 FM Antenna
AM AntennaRemote Control User Manual
- Home Entertainment AV Receiver Package with 5.1CH Speakers
- Bluetooth Connectivity
- 4 HDMI Input, 1 HDMI Output
- Easy Selectable Button to choose HDMI Receiver Mode or HDMI Switch Mode.
- 3D(1080P) HDMI Video ready
- 4K x 2K resolution support(HDMI 1.4)
- 3.5mm Aux in for MP3 Players as iPhone
- AM/FM Tuner with 22 Radio Presets(11 FM, 11AM)
- 2 MIC Input with independent MIC controls for Treble/Bass and Volume
- Digital EQ Matrix sound
- Full Function Remote control
- 300 Watts Max Sound Power
- Digital VFD Display
- Switchable Dual Power Voltage : 115V/230V (230V Preset)
- Power surge protection(Current and Voltage) and Short circuit protection
- Output : 6Channel Speaker Output : Left, Right, Surround Left, Surround Right, Center and Subwoofer
- Easy Cable connection(banana cables included)
4
HDMI Cable
Banana Cable x 6ea
1. POWER: Turn the unit on or back to Standby
2. VFD Display: Displays information about current mode, playback etc.
3. Master Volume: Adjust master volume
4. MIC1: Microphone jack (1)
5. MIC2: Microphone jack (2)
6. MIC1 Vol: Adjust MIC1 volume independently
7. MIC Vol: Adjust master microphone volume
8. AUX 1/2/3: Switch to AUX 1-3
9. HDMI 1/2/3/4: Switch to HDMI 1-4
10. FM/AM: Switch to select FM/AM radio tuners
11. MP3/iPhone: Switch to MP3/iPhone (3.5mm AUX- in jack) input
12. MUTE: Mute or unmute audio output
13. TUNER: Adjust FM/AM tuner frequency
14. MIC2 Vol: Adjust MIC2 volume independently
15. MP3/iPhone: 3.5mm aux input jack
PANEL AND REMOTE OPERATION
Front and Back Panel
5
* UBR510B(HDMI 1.4) is not compatible with Ethernet & ARC.
PANEL AND REMOTE OPERATION
Name Function
1.STEREO DV D/CD/PHONE/TUNER/MP3/
iPhone INPUT
Light up when DVD, CD, PHONE, FM/AM, Mp3/
iPhone input.
2.AC-3PROLOGIC HDMI INPUT Light up when 5.1channel or HDMI 1/2/3/4 input.
3.DSP
4.DIGITALDISPLAY
5.KHz MHz KHz MHz ICON Light up when tuner input is selected and indicates
the value on the display for KHz/MHz.
6.SPECTRUM DISPLAY Light up to display the spectrumof dierent channel.
Rear Panel Connection Setup
FrontPanelDisplayWindow
DSP STATE ICON Light up when play DSP eect.
Light up to display value of current input mode.
6
AMPLIFIERS
Surround Left Front left Front Right Surround
Right
Center
Subwoofer
115V 230V
Preset to 230V
AC Power Outlet
A plug adaptor for 230V is included and
put on the at 110V UL plug as default.
Please take the plug adaptor out and
use in case of 110V/120V usage.
HDMI IN (sources may
include: TVs, disc players,
game consoles, computers,
media servers)
Blu-ray/DVD player
TV/Monitor Screen
Stereo Output
PANEL AND REMOTE OPERATION
Remote Control
Bluetooth Playback Control Buttons
POWER: Turn unit on or back to Standby.
Receiver Switch : Choose Receiver mode or Switch
mode (Default set to receiver mode)
HDMI 1/2/3/4 : Switch to HDMI input 1-4.
AUX 1/2/3 : Switch to AUX input 1-3.
MP3/iPhone : Switch to MP3/iPhone (3.5mm aux
in jack) input.
BT : Switch to Bluetooth input.
FM/AM : Switch to FM/AM tuner input.
CH.mode : Switch between multichannel audio
- 2.1 : 2 channels
- 3.1 : 3 channels
- 5.1 : 5 channels
DSP : Cycle through Digital Sound Processing
options (Live/Hall/Church) by pressing the button
rep eatedly.
VOL+/- : Adjust Master Volume
L/R : Adjust Left/Right speaker sound balance
TreB +/- : Adjust Treble balance
Bass +/- : Adjust Bass balance
Surround R/L Vol +/- : Adjust side surround speaker
R/L volume
Center Vol +/- : Adjust center speaker volume
Subwoofer Vol +/- : Adjust subwoofer volume
Numbers 1-11: Number buttons
Memory : Use in FM/AM mode to preset stations
SCAN +/- : Tune the frequency in FM/AM mode
Pairing: Press when ready to pair via BT
: Play from the beginning of the track. Press
again quickly to play the previous track
: Play next track
: Play/pause from the paired device.
7
Mode Audio Out Video Out
Receiver Mode 5.1CH SPK TV
Switch Mode TV’s SPK TV
In case HDMI devices are well connected to receiver and
to TV through the receiver by HDMI cables, by pressing
“Receiver & Switch Select Button”, receiver mode or switch
mode can be selected easily.
1
1. To open the battery compartment, press on the battery cover and slide it out.
2. Insert 2 AAA batteries, making sure to match +/- polarities as marked in the compartment.
3. Close the battery cover.
PANEL AND REMOTE OPERATION
Battery Installation
CAUTION
To prevent damage to the remote control, make sure to install batteriescorrectly.
Do not mix old and new batteries.
Dispose of batteries safely and appropriately. Contact your local authorities or dealer
for advice on battery disposal.
Keep batteries out of reach of children.
8
INPUT MODES
There are many input options available with this unit, enabling multiple connections set up at the same
time and easy switching with the touch of a button. Ensure that all cable connections are fuly set up
before turning the system on. Press the corresponding input source button on the remote control or
main unit front panel to switch to the desired mode.
1. HDMI 1/2/3/4 Use HDMI cables to connect to compatible Audio/Video media
players for audio output and video passthrough. The video signal will
be output through the HDMI OUT jack so that the picture can be
shown on a connected TV while the audio is played through the home
theater speakers. Please make sure that the receiver is in “RECEIVER” mode.
2. AUX 1/2/3 Input audio from compatible media players or TVs by using a L/R audio cable.
3. MP3/iPhone
4. MIC 1/2
3.5mm aux in jack
Input audio by plugging in up to two microphones.
Input audio by pairing the unit with compatible media players such as
smartphones and computers.
Input audio from iPhones, iPods, MP3 players or similar devices by
using a compatible auxiliary cable.
Switching Input Modes
Use the buttons on the remote control or the main unit to switch to a desired input connection.
Note : Changing inputs may take a few seconds.
1. HDMI
HDMI input sends audio signals to the home theatre speakers and video signals to HDMI OUT
in receiver mode.
Example: Blu-ray player connected to HDMI1, TV connected to HDMI OUT
1). Make sure that the Blu-ray player and the TV is turned on and set to the correct input source.
2). Switch to HDMI1 by pressing HDMI1 on the remote control or main unit.
3). Start playback on the Blu-ray player. Video should display on the TV and audio output
through the home theatre system.
4). Adjust the master and/or surround speaker volumes as desired.
Note : This setup is compatible with 3D Blu-ray players and 3D TVs. Both must be connected to play
3D movies together with the home theatre.
2. AUX
AUX input sends audio signals from a connected media device to the home theatre speakers through
a L/R audio cable.
Example: TV or media system connected to the unit using a L/R audio cable at AUX1
9
5. Bluetooth
Inhaltsverzeichnis
