UCHIDA AeroCut Bedienungsanleitung

OPERATION MANUAL

UCHIDA YOKO CO., LTD., TOKYO, JAPAN

Jul 14, 2011 USA

•Use machine only after reading the "Safety Instructions" given below carefully.

•These safety instructions are given to ensure that the machine will be used safely

and properly and to prevent operators from sustaining harm and injuries.

SAFETY INSTRUCTIONS

Definition of Symbols and Notes

In this manual the following names and signs stand for possible dangers.

Danger

This symbol stands for immediate danger threatening the life and

health of persons. Disregarding these instructions may cause

severe damage to health and even serious injuries.

Caution

This symbol stands for an endangering situation that may occur.

Disregarding these instructions may lead to slight injuries or

damage to property.

Note

This symbol stands for notes, operational hints, and other useful

information.

They are convenient for exploiting the machine’s functional abilities.

１

SAFETY INSTRUCTIONS

Explanations of the illustrations used in the Safety Instructions are given as follows:

Danger

1. Don't open the cover of the equipment. There is a danger of receiving an injury

or electric shock.

2. Turn off the power supply beforehand when attaching or detaching the

perforating blade. There is a danger of receiving an injury.

3. Don't touch any rotating part. There is a danger of receiving an injury.

２

Caution

1. Don't put a hand into the cover or a clearance between parts. There is a

danger of receiving an injury.

2. Don't bring a hand, face, hair, sleeves of clothes and the like close to the

rotating parts of the machine. There is a danger of receiving an injury.

3. Don't touch the blade point of the cutter. There is a danger of receiving an

injury.

4. Don't touch the blade point of the perforating blade. There is a danger of

receiving an injury.

5. Turn off the power supply beforehand when setting the feed table.

There is a danger of receiving an injury.

6. Turn off the power supply beforehand when setting the stacker. There is a

danger of receiving an injury.

7. Turn off the power supply beforehand when setting the waste bin. There is a

danger of receiving an injury.

8. Turn off the power supply beforehand when removing paper scraps. There is

a danger of receiving an injury.

9. Avoid the combined use of the creaser and the perforator, as it may cause a

paper jam or a mechanical failure.

10. For the perforator, papers of weight 65 lbs (Cover stock) [176 g/㎡] or less is

to be used. Using heavier paper may cause a paper jam or mechanical failure.

11. Do not exceed the MAX level when stacking the paper. Exceeding it may

cause a mechanical failure.

12. Turn off the power supply beforehand when starting maintenance or

inspection. There is a danger of receiving an injury.

13. When you install a machine, please install to a place with no dust, and the

place which is not influenced with a liquid. It becomes the cause of failure if

the installation method is mistaken.

14. When you put a machine into operation, please change into the state

where all covers were closed. If it works where a cover is opened,

there is fear of an injury.

３

４

Introduction

Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety

Instructions" (page 2 to page 3) to ensure that the machine will be used properly.

Keep the manual at an appointed place with care so that it may be accessible whenever

necessary.

The specifications of this product are subject to change for improvement. Therefore,

don't mistake the "Operation Manual" of one product of the same model for that of

another because descriptions in the "Operation Manual" of products of the same model

may differ.

５

Contents

1. Before use........................................................................................................................................ ６

(1) Description and quantities of accessories...................................................................................６

(2) Exterior features.......................................................................................................................... ７

(3) Installation................................................................................................................................... ９

2. Operating instructions ...................................................................................................................１１

(1) Checks before use ...................................................................................................................１１

(2) Setting of stacker......................................................................................................................１１

(3) Waste box setting.....................................................................................................................１２

(4) How to attach the business card stacker..................................................................................１２

(5) Paper setting............................................................................................................................１３

(6) Paper slant adjustment.............................................................................................................１４

(7) Crease depth adjustment .........................................................................................................１４

(8) How to attach the perforator.....................................................................................................１５

(9) How to adjust the perforation location......................................................................................１６

(10)How to adjust the depth of perforation.....................................................................................１７

3. Operational method.......................................................................................................................１８

(1) Basic operation.........................................................................................................................１８

(2) Slitter initial location movement................................................................................................１８

(3) Format selection.......................................................................................................................１９

(4) Free entry.................................................................................................................................２１

(5) User program retrieval..............................................................................................................２１

(6) User program registration.........................................................................................................２２

(7) Setting of slitter and feed table.................................................................................................２３

(8) Operation number cancellation.................................................................................................２３

(9) Manual operation......................................................................................................................２４

(10) Speed change ........................................................................................................................２５

(11) Cut mark on/off selection........................................................................................................２６

(12) Automatic operation................................................................................................................２６

4. Instructions for use........................................................................................................................２７

(1) If the machine stops during operation ......................................................................................２７

(2) If Paper scrap remains on the machine....................................................................................２８

(3) Details concerning errors..........................................................................................................２９

(4) If the cut measurement does not match the input value...........................................................３４

5. Product specifications ...................................................................................................................３５

6. Equipment, Electric circuit and parts.............................................................................................３７

7. Ordering consumables, etc. ..........................................................................................................４０

1. Before use

(1) Description and quantities of accessories

Electric power cord 1pc.

Hexagonal wrench 0.08” X 1pc.

Tweezers 1pc.

Waste ejector

1pc.

Instruction manual 1pc.

Waste box 1pc.

Paper guide (Large)

1pc.

Paper guide (Small)

5pc.

６

(2) Exterior features

1. Name of parts

1. Stacker 6. Slitter

2. Touch Panel 7. Feed Table

3. Crease Depth Adjustment Dial 8. Slant Adjustment Dial

4. Waste Box 9. Perforator

5. Safety Cover 10. Caster

７

2. Electric-power-related points

The electric power switch and the inlet are located inside the machine, below

the feed table.

1 Power switch ①When it is set at “I”, the power is turned on.

②When it is set at “O”, the power is turned off.

2 Inlet Plug in the electric power cord here.

3 Electric Power

Cord Plug this to the inlet.

８

(3) Installation

The

machine installation method

Unlock

Lock

Please be sure to LOCK a caster brake after making it move to the target position, when

installing a machine.

Caution

When you install a machine, please install to a place with no dust,

and the place which is not influenced with a liquid. It becomes the

cause of failure if the installation method is mistaken.

2. Setting of feed table

Insert the feed table to the paper feeder, and set the feed table’s slotted holes onto the

protruding bolts on the machine. Install the 2 screws as shown below.

Feed table

Protrusions

(M6x10)

Screws

９

Inhaltsverzeichnis

Andere UCHIDA Bindemaschine Handbücher

UCHIDA

UCHIDA AeroCut X-Pro Bedienungsanleitung

Beliebte Bindemaschine Handbücher anderer Marken

GBC

GBC CombBind C800pro Bedienungsanleitung

JBI

JBI Alpha-Doc MKIII Bedienungsanleitung

GBC

GBC CombBind A20 Bedienungsanleitung

GBC

GBC DocuBind P100 Bedienungsanleitung

Peach

Peach PB300-20 Bedienungsanleitung

Morgana

Morgana DigiBook 450 Bedienungsanleitung

Rexel

Rexel CB345E Bauanleitung

GBC

GBC AP-2 Bedienungsanleitung

Opus

Opus MB 300 Bedienungsanleitung

Duplo

Duplo DC-645 Bedienungsanleitung

Akiles

Akiles AlphaBind Kurzanleitung

ibico

ibico Thermal Binder 260 Bedienungsanleitung

Rollabind

Rollabind PBS 2000 Bedienungsanleitung

SYSFORM

SYSFORM CP340H Bedienungsanleitung

GBC

GBC THERMALBINDER400T Bedienungsanleitung

GBC

GBC CombBind C20 Bedienungsanleitung

Renz

Renz RENZ DTP 340A Betriebsanleitung

Ricoh

Ricoh RB5020 Bedienungsanleitung