Ultimaker 2 Extended Bedienungsanleitung

Andere Handbücher für 2 Extended

12

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Ultimaker 3D-Drucker Handbücher

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker UM2 Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Konfigurationshandbuch

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker METHOD XL Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker EXTRUSION UPGRADE Bedienungsanleitung

Ultimaker

Ultimaker 2+ Connect Gebrauchs- und Pflegehandbuch

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungs- und Wartungshandbuch

Ultimaker

Ultimaker 3 Extended Einrichtungshandbuch

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Leitfaden

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker Original Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung

26.11.2017

Installation Guide

Ultimaker 2+ and 3, Magnetic Base

Plate

These are installation instructions for the GeckoTek Magnetic Base for

the Ultimaker 2, 2+, Extended and Ultimaker 3. When you are finished,

you will be able to use GeckoTek Build Plates without the need for

clips or tape.

The install was demonstrated on a Z stage that was removed from

the 3D printer. This was done for convenience and to allow for

better pictures and is not necessary or recommended.

If you have questions or discover an issue with the installation process,

please let us know.

Total install time is 5-10 mins.

You will need the following to complete the installation process:

•M2x5 screws (included)

•Thin Phillips screwdriver

•Pliers or wrench

Step 1: Remove the stock glass build platform by rotating the

retaining clips out of the way and sliding the glass plate forward.

Step 2: Loosen the 3 leveling screws that hold the print bed heater on.

Remove the thumb nuts and screws and set them aside for later.

Step 3: Using a wrench, loosen the screws attaching the power and

thermistor wires to the print bed heater. You should not be able to

separate the print bed heater from the 3D Printer.

Step 4: The front two glass retaining clips will come off with the

leveling screws. Using the allen wrench and pliers, remove the screws

holding the back two clips on. Set the screws and nuts aside for later.

Step 5: Attach the Magnetic Base to the stock bed heater using the

included M2.5 Screws. The mounting holes in the Magnetic Base line

up with the small slots where the retaining clips that held the glass

plate used to be.

Step 6: Attach the Magnetic Base with heater attached to the Z-

carriage with the 3 leveling screws. Tighten finger tight with the thumb

nuts and Phillips screwdriver.

Step 7: Attach the GeckoTek Build Plate to the Magnetic Base and

center it. Then follow the manufacturer’s recommended bed leveling

procedure with the Build Plate in place.

You are now ready to 3D Print with your GeckoTek Build Plate!