Ultimaker S3 Installationsanleitung

Ultimaker S3 Ultimaker 2+ Connect

Basic instructions for 3D printing using:

What you need to bring:

Laptop USB

and / or

Cura software If your file needs support material, we recommend using

an S3 printer, which can use dissolvable PVA support. If

no support is required, we recommend using a 2+

Connect printer. But either type of printer can be used.

Orientate your file to eliminate or minimise the support

material required.

The material / nozzle settings should be set to:

or the ‘generic’, non-branded version of the material.

The nozzle used for providing support material on an S3

can be adjusted from the ‘support’ drop down in custom

settings. The printers are set up for Fine -0.1mm layer

height only. Overall, we recommend using the standard

settings for Fine -0.1mm. The infill can be set as desired,

but should be between 5% and 15%. A brim can be

replaced with a skirt in most cases where the model is

unlikely to fall over.

For these printers we recommend using Cura as the

slicing software. Export your model from your CAD

software as an STL, 3MF, or OBJ file.

Watch this Cura beginner’s tutorial:

www.youtube.com/watch?v=NsGOoi3677M

A –Check spool(s) are clear of obstructions and fed

into the feeders.

B –Check clamp(s) are in a down position on feeders.

C –Switch on the printer, and wait until ‘ready to print’

appears on the touch screen.

Do not attempt any maintenance or material changes.

Report these issues.

2Leave a note with your name and student email address

next to the machine, so you can be contacted if necessary.

A –Check that the glass bed is secured and clear of debris

(if not clean see step 4B). The bed is fully secured if the

clips close parallel with the glass bed.

B –Apply a light, single layer of glue to the bed, only on

areas where you have placed models in the slicing

software. Glue is found in the box above each printer.

C –Put your .ufp or equivalent gcode file onto a personal

USB or the printer’s USB. Plug this into the port left side

of the touch screen. Press ‘select from USB’.

Do not change any settings or attempt to perform

maintenance from the touch screen menu. Report issues.

3A –Select your file from the list. Scroll to page 2 once the

file is selected to see and check an image of the file. Select

Print. If a material change warning displays, as long as the

materials set in the slicing software match up closely with

those on the printer, it is fine to select ‘print anyway’.

B –Wait at the machine until your file begins to print, in

order to notice any issues that arise during the printer’s

start up procedure. This takes a few minutes. Caution: the

bed and nozzles warm up and become hot to touch during

printing.

C –Note the time it will take to print the file. Return as

soon as possible after the file has been printed. This will

make it easier to remove the printed models from the glass

bed, and frees up the printers for others to use. If you have

used the printer’s USB, clear your file off the stick.

If there is a problem during printing, ‘pause’ or ‘abort’

buttons can be selected. Follow on screen instruction to

complete the chosen procedure.

A –When the print is complete, carefully remove the

glass bed from the printer. Peel away the model from the

bed, or carefully use a provided scraper to assist. Do not

excessively finish or remove build material from your

model in the lab –take your model away and do this

elsewhere.

B –Use a scraper / glass cleaner / paper provided to

clean the bed of glue and build material. Do not spray

cleaner on the bed while it’s inside the printer. When

clean, return the bed to the printer. Clean away all mess

into the bin. The printer and surrounding area should be

left in the same condition as you hopefully found it.

C –Follow the onscreen instructions until the printer is

returned to its ‘ready to print’ screen. Turn off the printer

using the switch on the back.

If your model was printed on an S3 printer, the support

material, Natural PVA, can be removed either by

breaking it away, or sitting the model in warm water until

dissolved, or softened enough to be easily removed.

Andere Handbücher für S3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ultimaker 3D-Drucker Handbücher

Ultimaker

Ultimaker Original Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Betriebsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Leitfaden

Ultimaker

Ultimaker 2 Go Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker Heated Bed Upgrade Kit Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker Ultimaker S5 Pro Bundle Bedienungsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungs- und Wartungshandbuch

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Leitfaden

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Einrichtungshandbuch

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung