Ultimaker UM2 Bedienungsanleitung

Assembly manual

The fast, easy to use, Open-source 3D printer

English Version 1.02

Table of Contents

A. Assembly of the Frame

B. Assembly of XY-axle

B1. Sliderblocks

B2. XY-axes

B3. XY-motors

C. Assembly of Z-stage

C1. Z-stage

C2. Placing Z-stage in the frame

C3. Stabilize Z-stage

D. Assembly of the Material feeder

E. Assembly of the Display

F. Assembly of the Hot-end

F1. Hot end

F2. Connecting the fans

F3. Eliminate cables

F4. Placing printhead in frame

G. Assembly of the Electronics

G1. Install the electronics

G2. install the housing parts

A. Assembly of the Frame Partnr. Part Amount

1024 Limit Switch, Black Short Wire 1x

1161 LED Strip Cold White 1x

1162 Limit Switch Blue Wire 1x

1163 Limit Switch Red Wire 1x

1203 ISO 7380 M3x12 6x

1204 ISO 7380 M3x16 35x

1213 DIN 962 Square Nut M3 A2 35x

1220 Ball Bearing F688-2RA 8x

1230 Front Panel 1x

1231 Back Panel 1x

1232 Left Panel 1x

1233 Right Panel 1x

1234 Bottom Panel 1x

1235 Top Panel 1x

Note: The amount of parts

is always times 1, except if

the amount indicates some-

thing dierent. Make sure

you have al the parts before

you start with the next step.

1. Remove the protection foil from the dibond and plexiglas

3. Put the Ball Bearings in the countersunk holes on the front,

left, right and backplate. Make sure you do not damage the

dibont and plexiglass plates. This is a total of 8 Bearings

4. Use a rubber hammer or

use wooden plate between the

hammer and bearing to get the

bearing in place, make sure the

anges ush with the plate.

2. Remove all material left over by the machine.

5. Take 35x M3 square nuts and place

them in the T-slots of the front-back, top

and bottom plate. use pliers or tweezers

to make sure the nuts are tted correctly

in the frame

7. Red Endstop on the left

plate (that’s plate with

the extra motor holes).

make sure the lip is facing

upwards (check photo)

6. Attaching the 3 end-

stops with 6x M3X12MM

(rm but not excessive

torque!

8. The blue end stop on the top plate.

The lip pointing inwards. 9. The black Endstop

on the back plate on

the bottom of the pla-

te. With the lip pointing

to the right.

10. Turn the Front pannel around

so the T-slots are visible. Now

clean the back of the front pannel

with acetone or alcohol, so the

LED strip will stick better.

11. Install the LED strip in

the machine. Remove the

stickytape from the rst LED

strip and start at the bottom

right of the plate. Then move

up wards until you reacht the

top right corner.

12. The second part of the LED strip

goes on the top of the front plate,

start at the right and go to the top

left corner.

13. Make extra sure to

stick the LED strip very

rmly on the housing.

Otherwise, it can deat-

tach at a later stage!

push between each LED

14. Attatch the Top and Bottom plate to the

back plate. Make sure all the T-slots are facing

inwards. Next ad the front plate and screw

everything together with M3x16mm screws.

15. Place the Two sides on

the machine. Use 35 M3x-

16mm screws to secure

them into place.

16. Make sure all the cables are

guided through the holes in the

correct way. (use photo’s for

reference)

Inhaltsverzeichnis

Andere Ultimaker 3D-Drucker Handbücher

Ultimaker

Ultimaker METHOD XL Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker Original Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Einrichtungshandbuch

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 2 Go Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungs- und Wartungshandbuch

Ultimaker

Ultimaker 3 Extended Konfigurationshandbuch

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker PVA Removal Station Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S3 Installationsanleitung

Ultimaker

Ultimaker EXTRUSION UPGRADE Bedienungsanleitung

Ultimaker

Ultimaker 2+ Connect Gebrauchs- und Pflegehandbuch

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker Original Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung