Ultimaker Heated Bed Upgrade Kit Bedienungsanleitung

English V1.0

Heated Bed Assembly manual

Original

Table of Contents

Introduction & Speciﬁcation p. 4

A. Preparing the frame. p. 5

B. Mounting the electronics. p. 11

C. Assembling the Z-stage. p. 15

D. Installing the Z-stage & electronics. p. 24

E. Updating the Firmware and Calibration p. 33

Introduction & Speciﬁcation

Support

We would love to hear from you. We are easy to reach and enjoy answering all

your questions. Technical assistance, sales enquiries or general information, we

are there for you. Find the information below to contact us.

General info@ultimaker.com

Support support@ultimaker.com

Sales sales@ultimaker.com

Marketing/PRpr@ultimaker.com

Phone +31 (0)345712017

Dear customer,

Thank you for purchasing the Heated Bed Upgrade Kit for your Ultimaker

Original!

This assembly manual will guide you through the build process step by

step. Besides this assembly manual there’s also a brand new user manual

available online: www.ultimaker.com/pages/support/manuals

There’s also a wealth of information, tips, tricks and amazing Ultimaker prin -

ted objects on our online community forum. Drop by and say hello:

www.ultimaker.com/forum

Visit YouMagine for fun projects and free printable models:

www.youmagine.com

Happy building and printing and we’ll be in touch!

Team Ultimaker

Technical speciﬁcation

Temperature

Operating heated build

plate temperature 50 - 100 degrees celsius

Printing with PLA 65 degrees celsius

Printing with ABS 100 degrees celsius

Electrical

AC INPUT 100 - 240 V,

Approx. 4 AMPS,

50 - 60 HZ

221watt max .

Power Requirements 24 V DC @ 9.2 AMPS

A. Preparing the frame. Part Amount

Drill bit 14mm 1

Drill bit 3,2mm 1

Handdrill 1

Scissors 1

(Blue) Tape 1

Hex Key Screwdriver 2 1

Hex Key Wrench 1.5 1

Powerplug Template 1

Heated Bed PCB Template 1

Note: Make sure you have

al the parts before you start

with the next step.

7Warning: When installing electronics or prefor -

ming any other maintenance on the machine, make sure

you are staticly discharged and ALWAYS DISCONNECT

THE POWER SUPPLY from the machine.

1. Use the Hex Key Wrench 1.5 to

undo the top two screws in the

Z-coupling.

2. Unscrew the Top caps (3B)

so you can remove the guiding

rods. Remember to save all the

nuts and bolts

3. Remove the guiding rods

from the frame

4. Lift the bed upwards and tilt

it to remove it from the frame.

5. Remove these 4 screws

from the Z-motor and save the

screws, you will re-use them to

install the new motor

6. Turn the machine on its side

and remove the Z-motor

7. Take the two templates and

the tape. You can use any tape

you want, just make sure it

sticks to the wood.

8. Cut out the Template with

the corner shape.

9. Line up the template with

the back left corner of the

frame and secure it with tape.

10. Take the handdrill and the

14mm drill bit, and drill out the

hole. You can use a center -

punch to create a nice starting

position.

Note: Make sure no wires are under -

neath the spot where you are going

to drill.

13. Line up the hole in the

template with the hole you just

drilled. Tape the template in

place.

14. Take the drill and the

3.2mm bit, and drill through

the 4 black circles in the tem -

plate.

11.Cut out the Heated Bed

PCB Template.

12. Cut out the hole in the tem-

plate and fold it on the red line.

Inhaltsverzeichnis

Andere Ultimaker 3D-Drucker Handbücher

Ultimaker

Ultimaker 2 Extended Bedienungs- und Wartungshandbuch

Ultimaker

Ultimaker 2 Go Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S3 Installationsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker EXTRUSION UPGRADE Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker PVA Removal Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Leitfaden

Ultimaker

Ultimaker Original Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Konfigurationshandbuch

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Einrichtungshandbuch

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Leitfaden

Beliebte 3D-Drucker Handbücher anderer Marken

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung