Ultimaker 3 Extended Leitfaden

Ultimaker Support

›

3D Printers

›

Ultimaker 3

›

Maintenance

Check the tension of the short belts

January 28, 2020 10:34

Maintaining proper tension on the short belts is important to ensure good print quality.

The short belts transfer the movements of the X and Y motors to the print head. If the

belts are too loose, the movements of the print head may not be accurate. It is

recommended to check the tension of the short belts at least once every three months.

Pluck the two short belts to check their tension. They should slightly resonate, like a

guitar string. It should not be possible to press the belt against itself. Furthermore, the

tension of the two belts should be equal.

To restore the tension, perform the following steps:

Loosen the Y motor by using the hex screwdriver to loosen the four bolts that hold the

Y motor to the left panel. Do not remove the bolts, but the motor should be able to

slide up and down.

Firmly press down on the motor with one hand. This ensures maximum tension on

the short belt

While still pressing the motor down, tighten the four bolts of the Y motor in a cross

pattern. First tighten the top-left bolt, then the bottom-right, next the bottom-left and

ending with the top-right. This ensures that the motor is attached straight

Perform the above steps for the X motor that is attached to the back panel.

Afterwards, check the tension of both belts again

Ultimaker

Ask our community of experts

Go to our community











Check the tension of the short belts – Ultimaker... https://support.ultimaker.com/hc/en-us/articles/...

1 of 3 12/15/20, 2:01 PM

Comments

0 comments

Article is closed for comments.

Articles in this section

Was this article helpful?





1 out of 1 found this helpful



Update the Ultimaker 3 firmware



Ultimaker 3 firmware release notes



Replace the build plate clamps of the Ultimaker 3



Replace the radial fans of the Ultimaker 3



Replace the axial fan of the Ultimaker 3



Replace the tube coupling collet of the Ultimaker 3



Replace the clamp clip of the Ultimaker 3



Replace the Bowden tubes on the Ultimaker 3

Check the tension of the short belts – Ultimaker... https://support.ultimaker.com/hc/en-us/articles/...

2 of 3 12/15/20, 2:01 PM

Recently viewed articles



Clean the feeders on the Ultimaker 3



Lubricate the lead screw of the Z motor on the Ultimaker 3



Check for play on the axles of the Ultimaker 3



Lubricate the Ultimaker 3 axles



Cleaning the Ultimaker 3



Ultimaker 3 maintenance schedule

Check the tension of the short belts – Ultimaker... https://support.ultimaker.com/hc/en-us/articles/...

3 of 3 12/15/20, 2:01 PM

Andere Handbücher für 3 Extended

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ultimaker 3D-Drucker Handbücher

Ultimaker

Ultimaker 2 Extended Bedienungs- und Wartungshandbuch

Ultimaker

Ultimaker 3 Extended Betriebsanleitung

Ultimaker

Ultimaker S3 Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker METHOD XL Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker EXTRUSION UPGRADE Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker ORIGINAL+ Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker Ultimaker S5 Pro Bundle Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 3 Extended Bedienungsanleitung

Ultimaker

Ultimaker EXTRUSION UPGRADE Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker 2 Go Bedienungsanleitung

Ultimaker

Ultimaker 2 Extended Bedienungsanleitung

Ultimaker

Ultimaker PVA Removal Station Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung