Ultra Start 430 Series Bedienungsanleitung

FCC/ID Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modifications not expressly approved by the part responsible for compliance

void the user’s authority to operate this devise.

INSTALL GUIDE

www.ultrastarters.com

Technical Support: 866-698-5872 ext 0

support@ultrastarters.com

Covers All 430, 440, 441 and CJ Series

Advanced Security Systems

COMPONENTS

- Three Button Remote transmitter’s (430 Series) -Control Module

- Four Button Remote transmitter’s (440 Series) - Plug-in Led

- Plug-in Valet Switch (Program Switch) - Multi-Tone Siren

- 10 Pin Main Harness - Installation Guide

- 2 pin Keyless Entry harness - Owners Manual

Table Of Contents Page 2

Components

Wiring Diagram (With 10 pin connector) Page 3

Wiring Diagram (With 11 pin connector) Page 4

Wiring Description Pages 5-6

Recommended Installation Procedures

Basic Installation - Quick start

Shock Sensor Adjusting

Test The System

Programming Page 7-9

Program Overview

Quick View Programming

Program Menu

System Reset

Transmitter Programming Page 10

Car Jack Mode (CJ series Only)

System Operation Page 11

Relay Diagrams Page 12

INSTALL MANUAL REMOTE VEHICLE SECURITY

PAGE 2

Table of Contents

Blue

Connect to hood and / or trunk pin Hood Input

Green

Connect to door pin. (-) when opened Door Input

Purple

Connect to door pin. (+) when opened Door Input

Black

Connect to chassis ground Ground Input

Brown

Connect to Siren wire. 2amp Maximum Siren Output

Red

Connect to constant power. 20amp input 12 Volt Input

Yellow

Connect to vehicles ignition wire Ignition Input

Gray

*500ma negative output

Trunk Release

Orange

*500ma negative output (-) When Armed

REMOTE VEHICLE SECURITY INSTALL MANUAL

PAGE 3

For modules with 10 pin connector only. See page 4 for 11 pin connector.

INSTALL MANUAL REMOTE VEHICLE SECURITY

PAGE 4

Blue

Connect to hood and / or trunk pin Hood Input

Green

Connect to door pin. (-) when opened Door Input

Purple

Connect to door pin. (+) when opened Door Input

Blk/White

Dome Light Supervision Output (-) Dome Light

Black

Connect to chassis ground Ground Input

Brown

Connect to Siren wire. 2amp Maximum Siren Output

Red

Connect to constant power. 20amp input 12 Volt Input

Yellow

Connect to vehicles ignition wire Ignition Input

Gray

*500ma negative output

Trunk Release

Orange

*500ma negative output (-) When Armed

Red

Blue

For modules with 11 pin connector only.

REMOTE VEHICLE SECURITY INSTALL MANUAL

PAGE 5

Recommended Installation Procedures

White (+) Park lights Park light output.

Orange* (-) When Armed Negative output when system is armed.

Grey* (-) Trunk Release Negative output for trunk release.

Yellow (+) Ignition Input Input from vehicles ignition wire.

Red (+) 12Volt Input Constant 12 Volt input.

Brown (+) Siren Output Positive output for siren.

Black (-) Ground Input System ground input.

Purple (+) Door Input Positive door pin switch input.

Green (-) Door Input Negative door pin switch input.

Blue (-) Hood Input Negative input from hood pin switch.

Blk/White* (-) Dome Supervision 30 second (-) output when disarmed.*

*This wire is only available on models with the 11 pin connector.

10 Pin / *11 Pin Connector

Green* (-) Door Lock Door Lock Output (Programmable)

Red* (+) 12 Volt Output 12Volt Output for voltage inverter.

Blue* (-) Door Unlock Door Unlock Output (Programmable)

*NOTE: 500ma outputs ONLY!

3 Pin Connector Red

Under Hood Connections- Route the hood pin (optional) and Siren wire

through the firewall, into the engine compartment. Always try to pull the wires

through a factory rubber grommet. If drilling through the firewall, BE CAREFUL.

Check for obstructions on both sides of the firewall. After drilling use a snap in

grommet to protect the wires from sharp edges.

Mounting the module-Never mount the module in the engine compartment.

Select a location under the dash to install the main module. Be certain that the

module is securely attached and does not obstruct any serviceable areas.

Mount the module so that it cannot be seen if looking under the dash as it could

be easily unplugged by a thief. The module must be free from all moving parts.

Mounting the Siren- Choose a location in the engine compartment that is

away from high heat sources and direct exposer to water. The siren should be

mounted as well as grounded to solid metal. Run the wiring for the siren so that

it can not be seen or reached from below the vehicle.

Wiring Descriptions

INSTALL MANUAL REMOTE VEHICLE SECURITY

PAGE 6

Step 3- Test And Adjust The Shock Sensor (see page 3)

Recommended Installation Procedures

Basic Install

Installing the LED- Choose a location that will be highly visible when the

LED is installed. Most vehicles are equipped with knock out panels in the

dashboard, these panels are easily removable and can be easily replaced if

necessary. Once the location is picked, use drill bit and drill a hole through the

panel. Test fit the LED into the hole. Plug the Led into the Red connector on the

main module.

Installing the Program Button- Choose a location to mount the Program

Button. This location should be hidden and not visible from outside the vehicle.

Once the location of the switch is picked, use a 1/4” drill bit and drill a hole.

Remove the nut and push the Program Button through the hole. Replace the

nut and tighten until the switch is secure. Plug the Program Button into the

Blue connector of the main module.

Step 1 - Connect All Of the Following Wires

Black Ground Input System ground input.

Yellow Ignition Input Input from vehicles ignition wire.

Red Power Input Constant 12 Volt input.

Brown (+) Siren Output Positive output for siren.

White (+) Park lights Positive park light output.

Green* (-) Door Input Negative door pin switch input.

Purple* (+) Door Input Positive door pin switch input.

*Test for door pin type (+ or -) then connect the appropriate wire.

Step 2- Plug-In The Module

Step 4- Test The System

Your Basic Install Is Complete!

REMOTE VEHICLE SECURITY INSTALL MANUAL

PAGE 7

Changing A Programmable Setting

Quick View Programming

To Enter Program Mode

1) Make sure ignition is in the off position.

2) Within three seconds turn the key ON the OFF.

3) Press and release the Program Button two times.

4) The siren will chirp and the lights will flash once to confirm.

NOTE: If unit does not enter Program Mode, repeat steps 2-3.

** The ignition input wire(yellow on the 10 pin connector) MUST be connected.

If it is not connected it will not be possible to enter the Program Mode.

1) Enter Program Mode As explained above.

2) When in program Mode, change the desired Program Setting by pressing

the transmitter buttons in the following sequences.

NOTE: The Systems Default Setting Are Shown In Bold Lettering.

Programmable Feature Press Buttons One Chirp Two Chirps

Shock Sensor Disable #3-#3-#1 Disabled Enabled

Arm / Disarm Chirps #2-#1-#1 Chirps Off Chirps On

Ignition Auto Locks #1-#3-#2 Off On

Door Lock Timing #1-#3-#1 3 Second .75 Second

Double Pulse Unlock #2-#2-#1 Two Pulses Single Pulses

Door Input / Voltage Sense #1-#1-#3 Voltage Door Pin

Passive / Active Locks #3-#3-#2 Active Passive

Passive / Active Arming #1-#2-#3 Active Passive

Car Jack Mode*#2-#1-#3 Deactivated Activated

Siren/ Horn Output** #3-#2-#1 Siren Horn

System Reset #3-#3-#3 Confirmed by Three Siren Chirps

*CJ series ONLY

**441 series ONLY

Programming

#1#1 #2#2

#3#3

#1#1 #2#2

#3#3

INSTALL MANUAL REMOTE VEHICLE SECURITY

PAGE 8

Enter Program Mode

Entering program mode is done by the following steps:

1) Make sure ignition is in the off position.

2) Turn the ignition key ON - OFF, leaving key in the OFF position.

3) Press and release the Valet button two times.

4) The siren will chirp one time to confirm entering program mode.

( If this does not happen, turn ignition off, wait five seconds and repeat steps 1-4).

Shock Sensor Disable

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence:

#3 - #3 then #1

3- The siren will respond with the following:

1 Chirp Shock Sensor OFF

2 Chirps Shock Sensor ON

Arm/ Disarm Chirp

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#2 - #1 then #1

3- The siren will respond with the following:

1 Chirp Chirps Disabled

2 Chirps Chirps Enabled

Ignition Auto Locks

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #3 then #2.

3- The siren will respond with the following:

1 Chirp Auto Lock Disabled

2 Chirps Auto Lock Enabled

Door Lock Timing

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #3 then #1

3- The siren will respond with the following:

1 Chirp 3 Second Door Locks

2 Chirps 0.75sec Pulses

Double Pulse Unlock

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#2 - #2 then #1.

3- The siren will respond with the following:

1 Chirp Double Pulse Unlock

2 Chirps Single Pulse Unlock

NOTE: Repeat sequence to change selection

REMOTE VEHICLE SECURITY INSTALL MANUAL

PAGE 9

Voltage / Door Pin Sensing

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #1 then #3

3- The siren will respond with the following:

1 Chirp Voltage Sensing- No Door Pin Connection Needed

2 Chirps Door Pin- Door Pin Connection Required

Passive / Active Locks

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#3 - #3 then #2

3- The siren will respond with the following:

1 Chirp Active Locks

2 Chirps Passive Locks

Passive / Active Arming

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#1 - #2 then #3

3- The siren will respond with the following:

1 Chirp Active Arming

2 Chirps Passive Arming

Car Jack Mode (CJ series ONLY)

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#2-#1 then #3

3- The siren will respond with the following:

1 Chirp Inactive

2 Chirps Active

Siren/ Horn Output (441 series ONLY)

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#3-#2 then #1

3- The siren will respond with the following:

1 Chirp Siren

2 Chirps Horn

Reset System

1- Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)

2- Press & release transmitter buttons in the following sequence

#3-#3 then #3

3- The siren will respond with the following:

3 Chirps System Reset

NOTE: Repeat sequence to change selection

INSTALL MANUAL REMOTE VEHICLE SECURITY

PAGE 10

Transmitter Programming

Follow the steps below to program the transmitters to the system s memory

Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.

Step 2 - Press and release the Program Button twice then press and hold.

Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.

Note: If the siren does not respond, repeat Steps1&2

Step 4 - Continue to hold the Program Button and press lock button on each of the

transmitter’s to be programmed(Maximum of 3 Different transmitter codes).

Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.

Exit - After five seconds the system will exit transmitter program mode automatically.

NOTE: You must program ALL of the transmitters to be used at one time. For the owner’s

security any transmitters not programmed at this time will be erased from memory.

*** This system will store a maximum of three transmitter codes in memory.

Car Jack Mode Activation (CJ series ONLY).

1) If the ignition key is On and a door is opened the Car Jack Mode

Timer will start. The siren will chirp one every second for 10

seconds then trigger into full alarm.

2) If the timer was activated by accident, within 10 seconds turn the

ignition key back to On then press and release the program

button one time. The Car Jack Mode Timer will stop.

3) If the timer is not deactivated Car Jack Mode will trigger into full

alarm. To deactivate turn the ignition On, then press and release

the program button 5 times then press unlock on the remote

transmitter.

Emergency Override.

If Car Jack Mode is not deactivated in time, the system will need to

be placed into Emergency Override. Turn the ignition key to the On

position then press and hold the program button for 20seconds. At

this time the customer can bring the vehicle back to the dealer for a

system reset.

Andere Handbücher für 430 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ultra Start Autoalarmanlage Handbücher

Ultra Start

Ultra Start 35 SERIES Bedienungsanleitung

Ultra Start

Ultra Start MCS-100 Bedienungsanleitung

Ultra Start

Ultra Start G-Series Bedienungsanleitung

Ultra Start

Ultra Start 1270 series Bedienungsanleitung

Ultra Start

Ultra Start 42xx Bedienungsanleitung

Ultra Start

Ultra Start 600 SERIES Bedienungsanleitung

Ultra Start

Ultra Start KEU-300 Series Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start MCS-100 Bedienungsanleitung

Ultra Start

Ultra Start 430 Series Bedienungsanleitung

Ultra Start

Ultra Start 1280 series Bedienungsanleitung

Ultra Start

Ultra Start 430 Series Bedienungsanleitung

Ultra Start

Ultra Start 441 Series Bedienungsanleitung

Ultra Start

Ultra Start G-Series Bedienungsanleitung

Ultra Start

Ultra Start 1180 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 660 Series Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Ultra Start

Ultra Start 45 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 640 Series Bedienungsanleitung

Ultra Start

Ultra Start 45xx Series Bedienungsanleitung

Ultra Start

Ultra Start 1350 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 640 Series Bedienungsanleitung

Ultra Start

Ultra Start KEU-300 Series Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung