Ultra Start 1172 SERIES Bedienungsanleitung

REV.2007.11.14A

1172 SERIES

Advanced Remote Starters &

Vehicle Security Systems

INSTALLATION GUIDE

FCC ID NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate

this devise.

www.ultrastarters.com

SYSTEM PROGRAMMING - Menu 1

PAGE 2

INSTALL MANUAL

TABLE OF CONTENTS

QUICK VIEW WIRING DIAGRAM..........................................................3-4

Connector Pin Configuration

Antenna Connector

Park Light Jumper

QUICK VIEW PROGRAMMING..............................................................5-9

Enter Program Mode

System Reset

Transmitter Programming

Menu 1,2,3 & 4 Quick View

Auto Tach Learning

Manual Tach Learn (Vehicles without start wire)

SYSTEM WIRING DETAILS................................................................10-14

Connector Views

Wiring Description

PROGRAM MENUS............................................................................15-21

Program Menu 1 Details

Program Menu 2 Details (4-Button Button Remote Required)

Program Menu 3 Details

Program Menu 4 Details

TACH MODES..........................................................................................22

Normal Operation

Hybrid Mode 1 &2

DOOR LOCK DIAGRAMS..................................................................23-24

Relay Diagrams

TRANSMITTER PROGRAMMING...........................................................25

Adding / Reprogramming Transmitter

DIAGNOSTICS..........................................................................................26

Diagnostic Chart

Diagnostic Memory

NOTES......................................................................................................27

CONTACT INFORMATION.......................................................................28

(4-Button Button Remote Required)

1172 SERIES

(+) GLOW PLUG - PROGRAMMABLE/ - SEE PAGE 13(+) START TRIGGER

SYSTEM PROGRAMMING - Menu 1

PAGE 3

1172 SERIES

INSTALL MANUAL

QUICK VIEW WIRE DIAGRAM

SYSTEM GROUND INPUT

SELECTABLE PARK LIGHT OUTPUT (DEFAULT POSITIVE)

STATUS LED

PROGRAM / VALET BUTTON

BLACK

WHITE

OUTPUT TO ACTIVATE IGNITION CIRCUITTHE VEHICLES BLUE

SELECTABLE OUTPUT* (DEFAULT 2ND IGN) SEE PAGE 11 WHITE*

12VOLT/ 30 AMP MAIN POWER INPUT RED

OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT YELLOW

12VOLT/ 30 AMP MAIN POWER INPUT RED

OUTPUT TO ACTIVATE ACCESSORY CIRCUITTHE VEHICLES GREEN

(-) AUXILIARY 1 OUTPUT - PROGRAMMABLE - SEE PAGE 13

BLACK

(-) AUXILIARY 2 OUTPUT - PROGRAMMABLE - SEE PAGE 13

RED/WHITE

(-) REARM OUTPUT - PROGRAMMABLE - SEE PAGE 13 YELLOW

(-) DISARM OUTPUT (PULSE WITH UNLOCK & BEFORE START) BROWN

(+ / -) TACH DETECTION INPUT (CONNECT TO COIL, INJECTOR...)

BLUE/WHITE

(-) HOOD PIN SWITCH INPUT (GROUND WHEN HOOD IS OPENED)

GREEN/WHITE

(+) BRAKE SWITCH INPUT (12VOLT WHEN BRAKE IS PRESSED)

PINK

BLUE

(-) HORN OUTPUT - PROGRAMMABLE - SEE PAGE 13 WHITE/BLUE

DO NOT INSTALL THIS SYSTEM INTO A MANUAL TRANSMISSION VEHICLE!!

SYSTEM PROGRAMMING - Menu 1

PAGE 4

INSTALL MANUAL

QUICK VIEW WIRE DIAGRAM

Position 1 or Position 2

GREEN

BLUE

N/A*

RED

BLACK

WHT/VIOLET

BYPASS MODULE DATA COMMUNICATION PORT

***FOR USE WITH COMPATIBLE BYPASS MODULES ONLY***

SELECTABLE PARK LIGHT OUTPUT

OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-)

OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-)

OUTPUT FOR VOLTAGE INVERTER*

12VOLT OUTPUT FOR BYPASS MODULE

GROUND OUTPUT FOR BYPASS MODULE

(-) WHILE RUNNING OUTPUT (BYPASS TURN ON) / STARTER DISABLE

* THE CENTER PIN OF THE KEYLESS CONNECTOR IS LOW CURRENT AND IS DESIGNED

TO SUPPLY POWER TO DOOR LOCK MODULES (DO NOT CONNECT TO RELAYS)

OVERLOADING THIS OUTPUT WILL DAMAGE THE MODULE!

**THIS CONNECTOR IS USED FOR ALARM MODELS ONLY.

*** FOR USE WITH COMPATIBLE BYPASS MODULES ONLY.

BY DEFAULT THE SYSTEM COMES WITH THE PARK

LIGHT JUMPER SET FOR POSITIVE PARK LIGHT

OUTPUT. TO CHANGE THE SYSTEM TO A NEGATIVE

PARK LIGHT OUTPUT, PLACE THE JUMPER IN THE

NEGATIVE PARK LIGHT POSITION SHOWN IN THE

DIAGRAM. (Position 2)

POSITIVE

PARK LIGHT

NEGATIVE

PARK LIGHT

1172 SERIES

SYSTEM PROGRAMMING - Menu 1

PAGE 5

INSTALL MANUAL

QUICK VIEW PROGRAMMING

Press Lock Press Unlock* Press Start Press #*

MENU 1 MENU 2 MENU 3 MENU 4

1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)

2 - Press and release the Program Switch located on the antenna 1 time.

*The Horn will chirp and the park light will turn on to confirm that the system

has entered Program Mode.

3 - Select the Program Menu by pressing the button that corresponds to the

desired Program Menu.

ENTERING PROGRAM MODE

1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)

2 - Press and RELEASE the Program Switch 1 time.

(Horn will chip to confirm program mode has been entered)

3 - Press and HOLD the Program Switch for 5 seconds or until the Horn Chirps 3

times.

4 - Turn the ignition key OFF to exit.

4 - Press and Release the Program Switch to advance through the settings.

*The horn will chirp and LEDs flash the same number of times as the selected setting.

5 - Press and hold the Program Switch to change the setting.

(The horn will honk and the park lights will flash to indicate the option selected)

6 - To exit Program Mode, turn the key off.

(Confirmed by Long Horn Chirp)

1172 SERIES

SYSTEM RESET

*4-Button Button Remote Required For Menu 2 and 4

SYSTEM PROGRAMMING - Menu 1

PAGE 7

INSTALL MANUAL

QUICK VIEW PROGRAMMING

PROGRAM MODE 1

SETTING #

LED

FLASHES

WIRE COLOR SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

OPTION 3

3 CHIRPS

1N / A

2WHITE

(2 PIN CONNECTOR)

3WHITE/BLUE

(9 PIN CONNECTOR)

VALET SETTINGS SECURE VALET

15 SECONDS

STANDARD VALET

5 SECONDS

PARK LIGHT OUTPUT 30 SECONDS ON

DISARM NORMAL OPERATION

HORN TIMING 5MS PULSED OUTPUT 50MS PULSED OUTPUT 10MS PULSED OUTPUT

PROGRAM MODE 2

PROGRAM MODE 1 - see page 16 for detailed instructions

PROGRAM MODE 2 - see page 19 for detailed instructions

IGNITION AUTO-LOCKS

DISABLED

SETTING #

LED

FLASHES

WIRE COLOR SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

OPTION 3

3 CHIRPS

1BLUE & GREEN

(DOOR LOCK HARNESS)

2WHITE/BLUE

(9 PIN CONNECTOR)

3BLUE & GREEN

(DOOR LOCK HARNESS)

4BLUE & GREEN

(DOOR LOCK HARNESS)

5BLACK

(9 PIN CONNECTOR)

6RED/WHITE

(9 PIN CONNECTOR)

IGNITION

AUTO-LOCK

IGNITION AUTO-LOCK /

UNLOCK

IGNITION AUTO-LOCK

ONLY

HORN SETTINGS HORN

CHIRPS DISABLED

HORN

CHIRPS ENABLED

DOOR LOCK PULSE

OPTIONS

DOUBLE UNLOCK &

SINGLE LOCK

DOUBLE LOCK & SINGLE

UNLOCK

SINGLE LOCK & SINGLE

UNLOCK

DOOR LOCK /

UNLOCK PULSES 0.25 SEC PULSES 3 SEC PULSES 0.1172 SEC PULSES

AUX OUTPUT 1 (-) ACCESSORY OUTPUT

(#) ACTIVATES CAR FINDER

2ND UNLOCK

(-) START OUTPUT

(#) ACTIVATES CAR FINDER

TRUNK RELEASE

AUX CHANNEL (#)

AUX OUTPUT 2 DOME LIGHT OUTPUT

1172 SERIES

(4-Button Button Remote Required)

SYSTEM PROGRAMMING - Menu 1

PAGE 6

INSTALL MANUAL

QUICK VIEW PROGRAMMING

2ND

IGNITION

SETTING #

LED

FLASHES

WIRE COLOR SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

OPTION 3

3 CHIRPS

1WHITE

(6 PIN CONNECTOR)

2BLUE & GREEN

(DOOR LOCK CONNECTOR)

3BLUE

(9 PIN CONNECTOR)

4YELLOW

(9 PIN CONNECTOR)

5 N / A

6 N / A

SELECTABLE

RELAY

2ND

STARTER 2ND ACCESSORY

SPECIAL DOOR

LOCK OPTIONS

UNLOCK BEFORE /

LOCK AFTER START

LOCK AFTER STARTER SHUT

OFF NO ADDITIONAL PULSES

GLOW PLUG/

START TRIGGER

(-) GLOW PLUG OR 20

SECONDS DELAY

POSITIVE TRIGGER TO

START (1 PULSE) GAS/ POSITIVE GLOW PLUG

RE-ARM OPTIONS PULSE WITH LOCK PULSE AFTER START

(DEFROST / SEAT)

PULSE WITH LOCK & AFTER

SHUTDOWN

RUNTIME 4 MINUTE RUNTIME

PRESS BUTTON ONCE TO

START

45 MINUTE RUNTIME 15 MINUTE RUNTIME

REMOTE START

ACTIVATION

PRESS BUTTON TWICE

TO START

PROGRAM MODE 3

PROGRAM MODE 4

PROGRAM MODE 3 - see page 21 for detailed instructions

PROGRAM MODE 4 - see page 23 for detailed instructions

AUTO TACH / TACHLESS

SETTING #

LED

FLASHES

WIRE COLOR SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

OPTION 3

3 CHIRPS

1BLUE / WHITE

(9 PIN CONNECTOR)

2 N / A

3 N / A

4 N / A

TACH OPTIONS HYBRID MODE 1

ADJUST FOR

OVER-CRANK

INCREASES TACH

SETTING BY 10%

ADJUST FOR

UNDER-CRANK

DECREASE TACH

SETTING BY 10%

TACH WAIT

SETTINGS

300ms TACH CHECK

DELAY 750ms TACH CHECK DELAY NO TACH CHECK DELAY

7 N / A LEDS FLASH WHEN

LOCKED/ ARMED

LED FLASHES

LEDS DO NOT FLASH

WHEN LOCKED/

ARMED

1172 SERIES

HYBRID MODE TWO

(4-Button Button Remote Required)

* If the vehicle does not have a starter wire a manual tach learn must be

preformed. (See Page 8)

** If Tach does not learn check for proper connection on the starter wire,

ignition wire and at the Tach connection. If the connections are good, reset

the system and try again.

-For best results connect the Tach wire to a fuel injector wire.

*** If the vehicle does not start when the remote starter is activated, the park

lights will flash a diagnostic code. (See Diagnostic Chart).

****If the vehicle still does not start, check all connections and check for a

factory installed Anti-Theft system. If the Anti-Theft prevents the vehicle from

starting the remote start will flash the park lights 7 times. The system does not

have to be Tach learned if this happens, simply start the vehicle with the key

and let it run for 5 seconds then turn off.

TACH NOTES

SYSTEM PROGRAMMING - Menu 1

PAGE 8

INSTALL MANUAL

TACH / TACHLESS LEARNING

1172 SERIES

SYSTEM PROGRAMMING - Menu 1

PAGE 9

INSTALL MANUAL

TACH / TACHLESS LEARNING

1172 SERIES

AUTO TACH/ TACHLESS LEARNING

Horn will chip to confirm that

the Tach/ Tachless has been programmed.

Start the vehicle with

the ignition key.

2 CHIRPS

**For Vehicles with 12volt START wire**

To Tach/ Tachless Learn the system simply start the vehicle with the ignition key. To

confirm that a proper Tach signal has been programmed the system will chirp the

Horn and flash the Park lights two times. If the Tach wire is not connected the park

lights will flash and the Horn will chirp 4 times to indicate Tachless Mode. If the Tach

is not learned when the start button is pressed the park lights will flash 7 times.

***The system must be Tach Learned before remote starting***

MANUAL TACH/ TACHLESS LEARNING

Start the vehicle with

the ignition key.

SYSTEM PROGRAMMING - Menu 1

**For vehicles with no 12volt START wire**

Many new GM and Chrysler vehicles do not have a 12volt start wire that the remote

start is connected to. Use the following steps to manually Tach learn the system.

Press and Hold the brake pedal, Start the vehicle with the key then place the

transmission into reverse to reduce the RPM. Press and release the program button

then press and hold it for 5 seconds. The Horn will chirp and the lights will flash

two times to confirm that a proper Tach signal has been programmed the system.

If the Tach wire is not connected the park lights will flash and the Horn will chirp 4

times to indicate Tachless Mode. If the Tach is not learned when the start button is

pressed the park lights will flash 7 times.

***The system must be Tach Learned before remote starting***

BRAKE

Hold the

brake

4 CHIRPS

Horn will chip to confirm

that the Tach/ Tachless has been

programmed.

2 CHIRPS

4 CHIRPS

SYSTEM PROGRAMMING - Menu 1

PAGE 11

INSTALL MANUAL

SYSTEM WIRING DETAILS

WHITE

SYSTEM GROUND INPUT

JUMPER SELECTABLE PARK LIGHT OUTPUT (+ OR -)

BLACK

BLUEOUTPUT TO ACTIVATE IGNITION CIRCUIT

RED30A HIGH CURRENT 12VOLT INPUT

YELLOWOUTPUT TO ACTIVATE START CIRCUIT

RED30A HIGH CURRENT 12VOLT INPUT

GREENOUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT

BLUENEGATIVE OUTPUT FOR UNLOCK

12+ OUTPUT FOR DOOR LOCK MODULE

GREENNEGATIVE OUTPUT FOR LOCK

4 PIN AUXILIARY SENSOR CONNECTOR

WHITE*SELECTABLE OUTPUT (DEFAULT SECOND IGNITION)

1172 SERIES

2-PIN CONNECTOR

6-PIN CONNECTOR

Andere Handbücher für 1172 SERIES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ultra Start Fernstartsystem Handbücher

Ultra Start

Ultra Start 2500 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1655XR Bedienungsanleitung

Ultra Start

Ultra Start 32 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 2250M Bedienungsanleitung

Ultra Start

Ultra Start 22 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1155 Series Bedienungsanleitung

Ultra Start

Ultra Start 1272 Series Bedienungsanleitung

Ultra Start

Ultra Start 25 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 32xx Series Bedienungsanleitung

Ultra Start

Ultra Start 1350 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1172 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 35 SERIES Bedienungsanleitung

Ultra Start

Ultra Start PRO Series Bedienungsanleitung

Ultra Start

Ultra Start 660 Series Bedienungsanleitung

Ultra Start

Ultra Start 32 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 22 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 3250 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1500 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 35 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1250 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1175 Series Bedienungsanleitung

Ultra Start

Ultra Start 22 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 15 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 12 SERIES Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung