Ultra Start 1250 SERIES Bedienungsanleitung

-The system must be placed into Service Mode before any service work is started on the vehicle. It is

the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no

liability or responsibility for accidental starting of the vehicle.

- CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)

- The Hood Pin Safety Switch Must Always be Installed!

- Never Install Automatic Transmission Remote Starters into a Manual Transmission Vehicle!

U.S.A. Model

This Manual Covers All 1250 Series

Remote Starters

Manual

Transmission

OWNER’S GUIDE

REMOTE VEHICLE STARTER

Table Of Contents

Page 2

Table Of Contents Page 2

Welcome Page 3

Feature List

About Ultra Start

FCC Notice

Remote Starter Functions Page 4

Remote Starting

Extended Runtime

Remote Stop

Idle Mode

Turbo Timer Mode

Optional Features Page 6-7

Lock Doors

Unlock Doors

Priority Unlock

Silent Lock and Unlock

Trunk Release *

Car Finder *

Garage Door Interface (optional) *

Panic

Constant Lock And Trunk Output

Cold Start/ Temperature Start Mode Page 8

2nd Car Operations Page 11

Examples Of 2nd Car Operations

Product Warranty Page 12

Reservation Mode (Manual Transmissions Vehicles) Page 5

* Button 4(#) Programmable

Service Mode Page 9

Activating & Deactivating Service Mode

Diagnostics Page 10

Diagnostics Chart

Diagnostic Memory

REMOTE VEHICLE STARTER OWNER’S GUIDE

This device complies with Part 15 of the FCC rules. Operation of this device is subject to

the following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the part responsible for

compliance voids the users authority to operate this device.

Congratulations on your purchase of an Ultra Start remote vehicle starter. Ultra Start

remote vehicle starters will provide years of comfort and convenience. To utilize and

understand this system to the fullest, please read this manual in detail.

FCC Notice

Welcome

It is our continuing objective to design and manufacture the absolute best Remote Car

Starters, Vehicle Security Systems, Keyless Entry Systems and Security Bypass units

available in today’s competitive market. This objective is met by utilizing installation

professionals with decades of industry experience to assist in each step of the design

process. This has allowed us to build products that are very installer and user friendly yet

offer advanced and innovative features. Our systems utilize intelligent programming and

auto learning systems and are designed to work properly in every vehicle. Our systems are

also designed wherever possible to be easily enhanced, allowing the consumer and the retailer

to enjoy easy and cost effective upgrades and additions to their system down the road. Our

limited lifetime warranty provides one of the best protection plans in the industry, giving

both the consumer and the retailer confidence when they invest in an Ultra Start product.

About Ultra Start

Feature List

- Remote Keyless Entry. - Panic Mode. (Personal Protection)

- Engine Idle Mode. - Turbo Timer Mode.

- Starter Disable. - Anti-Grind Protection.

- Dual Car Operation. - User Extendable Runtime.

- Safety Start Mode. - System Override Protection.

- Remote Service Mode. - Window Roll-Up/ Down.

- Park Light Diagnostics. - Up to 4 Different Transmitter Codes.

- Ignition Auto Locks. - Cold Start Mode With 4 Start intervals.

Page 3

Remote Starting

Remote Starter Functions

1.Press and release the button.

2.The park lights will flash and the horn (optional) will honk one time.

3.The vehicle will then remote start. The park lights will flash four times then

remain on while the vehicle is running*.

Note: If the remote starter fails to start, the park lights will flash a Trouble

Shooting Code. Count the number of flashes and refer to the

Diagnostics Chart on page 10.

Never remote start if the vehicle is parked in a garage or attached

carport! Operate in a well ventilated area only.

Remote Stop

1.Press and hold the button for three seconds. The remote starter will

shut down. The park lights will flash and the horn (optional) will honk 2

times to confirm shutdown.

Note: Pressing the brake pedal or opening the hood will also shut down

the remote starter.

Idle Mode

1.While the vehicle is running with key, press the button.

2.The park lights will turn on and the horn (optional) will honk once.

3.Turn the ignition key off and the vehicle will continue to run for the

programmed run time.*

Extended Run Time

1.Press and release the button while the vehicle is running.

2.The system will respond with one park light flash and one horn honk

(optional) to confirm Extended Runtime. The system will reset the run

time*.

Note: Extended runtime will not work if the runtime is programmed for 4

Minutes.

Turbo Timer Mode

1.While the vehicle is running with key, press the #button.

2.The park lights will turn on and the horn (optional) will honk once.

3.Turn the ignition key off and the vehicle will continue to run for

approximately 2 minutes.

*(Default 15 minutes)

Page 4

OWNER’S GUIDE

REMOTE VEHICLE STARTER

Manual transmission remote starters must be set into Reservation Mode before the

remote starter will activate. There are two different ways to place the system into

Reservation Mode. The activation type of Reservation Mode is determined when the

system is installed. The default setting is Auto Reservation Mode.

Auto Reservation Mode

Step 1 - While the vehicle is running, place into neutral and apply the park brake.

Step 2 - Press and release the brake pedal twice. The park lights will flash twice,

the horn (optional) will honk twice and the doors will unlock (optional).

Step 3 - Turn the ignition key off and the vehicle will continue running.

Step 4 - Exit the vehicle and close all the doors. The vehicle will then shut off *.

Manual Reservation Mode (Dealer Programmable Feature)

Step 1 - While the vehicle is running with the key, place transmission into neutral and

apply the park brake.

Step 2 - Press and release the #button. The park lights will flash twice, the horn

(optional) will honk twice and the doors will unlock (optional).

Step 3 - Turn the ignition key off and the vehicle will continue running.

Step 4 - Exit the vehicle and close all the doors.

Step 5 - Press and hold the button for 3 seconds, the vehicle will then shut off.

*****THE VEHICLE MAY NOW BE SAFELY REMOTE STARTED.*****

(See page 4 for Remote Starter Functions.)

If Reservation Mode is not set, the remote starter will not activate. When the start

Button is pressed the park lights will flash 4 times. 4 flashes is the diagnostic code

for “Not in Reservation Mode”

Note: Reservation Mode will reset if the doors of the vehicle are opened. To re-enter

the vehicle without canceling the Reservation Mode (forgot something..) The

vehicle must first be remote started. While the vehicle is running the door may

be opened, when done in the vehicle, close the door and hold the button

until the remote starter shuts off.

* If the vehicle has dome light delay, the vehicle may stay running until the dome

light turns off. This is normally no longer than 30 seconds.

Page 5

REMOTE VEHICLE STARTER OWNER’S GUIDE

Press and hold the UNLOCK button doors will unlock (optional). Continue

holding until the trunk release will activates.

* The trunk release will be confirmed by one park light flash and horn

(Optional) honk.

Note: The trunk release output will not activate when the ignition key is in the

On position.

1.Press and release the LOCK button on the remote transmitter.

2.The park lights will flash and the horn (optional) will honk one time.

3.Thedoorswilllock.

4.The LEDs on the antenna will start flashing within five seconds.

Note: If installed, the starter disable will activate.

1.Press and release the UNLOCK button on the remote transmitter.

2.The park lights will flash and the horn (optional) will honk two times.

3.The doors will unlock.

4.The LEDs on the antenna will stop flashing.

Note: If installed, the starter disable will deactivate.

1.Press and release the LOCK & UNLOCK buttons at the same time.

2.If the doors are locked this will unlock the doors without horn honks, the

park lights will flash two times to confirm the doors have unlocked.

3.If the doors are unlocked this will lock the doors without horn honks, the

park lights will flash one time to confirm they have locked.

Lock Doors

Unlock Doors

Silent Lock and Unlock

Trunk Release- Default Unlock Button

Page 6

Optional Features...

OWNER’S GUIDE

REMOTE VEHICLE STARTER

Car Finder (Default Setting)

1. Press and hold the #button for 3 seconds.

2.The park lights will flash and the horn(optional) will honk 5 times.

Note: This feature can be used to locate the vehicle in a crowded parking lot.

Trunk Release on the # button.

1. Press and hold the #button for 3 seconds. The park lights will flash and the

horn (optional) will honk once. Continue holding the unlock button until the

trunk release activates.

Garage Door Activation (Requires Garage Door Interface)

1. Press and hold the # button for 3 seconds. The optional garage door

interface will activate.

* The system will have no conformation for Garage Door Activation.

Button 4(#) - Optional operations(Dealer programmable feature)

This feature can be used on some vehicles to roll-up the windows or to

close a power sunroof. To activate the Constant Lock output. Press

and release, then press and hold the LOCK button. The lock output of the

remote starter will stay active until the LOCK button is released.

This feature can be used on some vehicles to roll-down the windows or to

open the power sunroof. To activate the Constant Trunk output press and

hold the UNLOCK button, the trunk release output of the remote starter will

stay active until the UNLOCK button is released.

Note: This output will stay active for up to 5 seconds.

Constant Lock Output (Optional Feature)

Constant Trunk Output (Optional feature)

Page 7

Optional Features...

REMOTE VEHICLE STARTER OWNER’S GUIDE

1. Press and hold the Lock button

2. The park lights will flash and the horn (optional) will honk.

Panic Mode Disable:

-Press and release the Lock button or

-Press and release the Unlock button.

Note: Panic will be active until disabled by the remote transmitter.

Panic

Cold Start/Timer Mode will start the vehicle at a user selectable start

interval or temperature setting. The vehicle can be set to start once every

1, 2, 3 or 4 hours in Timer Mode or 0,-5,-15 or -25 Celsius in Temperature

Mode (LT Models Only) for a maximum 12 starts.

The vehicle will start at the selected start interval/temperature and run for the

programmed runtime (default 15min). Cold Start/Timer Mode must be set

each time the user wishes to use the feature.

Example- Timer Mode. If the 4 hour start cycle was selected, the vehicle

will start once every 4 hours and run for the programmed runtime.

(default 15 min).

Example- Temperature Mode (LT models only). If the -15 Celsius start

cycle was selected, the system will monitor the temperature (every 2

hours) until it falls below -15. The remote starter will start and run for the

programmed runtime. (default 15 min)

To Enter Cold Start/Timer Mode.

Method 1- Press and release the #button, then press and hold the

button for 6 seconds or until park lights turn on.

Method 2 - Press the LOCK and buttons at the same time for 3

seconds or until the park lights will turn on.

While the park lights are on the start cycle can be selected.

1 hour or 0C Press LOCK button 1 Park light flash

2 hour or -5C Press UNLOCK button 2 Park light flashes

3 hour or -15C Press button 3 Park light flashes

4 hour or -25C Press # button 4 Park light flashes

Note: The optional Low Temp sensor must be installed for the temperature

settings to be available. (LT Models only)

To Cancel Cold Start/Timer Mode

Method 1- Press and release the #button, then press and hold the

button for 6 seconds.

Method 2- Press the LOCK and buttons at the same time for 3

seconds.

Note: Pressing the brake pedal or turning the ignition to the ON position will

cancel Cold Start/Timer Mode. Cancellation will be confirmed with 2

park light flashes and 2 horn honks (optional).

*****Never remote start or set the Cold Start Mode if the vehicle is

parked in a Garage or Attached Carport!

Cold Start/Timer Mode

Page 8

OWNER’S GUIDE

REMOTE VEHICLE STARTER

Page 9

System Service Mode will disable the remote starter. This will only effect the remote start

portion of the system. The optional lock, unlock and trunk release features will still be

operational.

When the vehicle is to have any under hood or service work done, the system must be

placed into Service Mode. This feature may also be used if a transmitter is lost, damaged

or if the system malfunctions.

ATTENTION:

TO AVOID SERIOUS INJURY, this remote start system must be set into

Service Mode before any under hood servicing is started. Service

Mode will prevent the vehicle from starting while the vehicle is being

serviced. It is the sole responsibility of the vehicle’s owner to place the

system into Service Mode. The manufacture accepts no responsibility

for accidental starting of the vehicle while the vehicle is being serviced.

System Service Mode (Valet Mode)

ENTERING SERVICE MODE

1. Turn the ignition key to the On position.

2. Press and hold the Program Button (Located on the antenna) for 5

seconds or until the horn (optional) honks five times.

Note: The LEDs on the antenna will turn on solid to confirm Service Mode.

If the start button is pressed while the system is in Service Mode the

park lights will flash 3 times slowly.

EXITING SERVICE MODE

1.Turn the ignition key to the On position.

2. Press and hold the Program Button (Located on the antenna) for 5

seconds or until the horn (optional) honks two times.

Note: Remote starter functions will be reenabled and the LEDs on the

antenna will turn off.

Being that the installer does not always see when the system shuts down or fails to

start, Diagnostic Memory will store in memory up to four shutdown codes.

This information can then be accessed to determine the source of the shutdown.

To Enter Diagnostic Mode:

Step 1 - Turn the ignition on then off. Press the Program Button and release.

Step 2 - The system will respond with three park light flashes and the horn will honk

(optional) the same number of times as the events in memory.

(Maximum 4 events, 4 honks).

NOTE: If the horn does not honk, there are no events in memory.

Step 3 - Press the Program Button once to view the last shut down code. The horn

will honk once to confirm code one.

(If the horn does not honk, there are no codes in memory.)

Step 4 - The LEDs on the antenna will flash a code corresponding to a shut down

trigger. Press the Program Button again to check the second code.

The horn will honk twice to confirm code two.

Step 5 - To Clear Diagnostic Memory. While in Diagnostic Mode press and hold the

Program Button for five seconds.

The park lights will flash and the horn (optional) will honk once.

NOTE: Once diagnostic memory has 4 shutdown events in memory, the system will not

Record any further shutdown events until the system memory has been cleared.

Diagnostics/ Diagnostics Chart

DIAGNOSTIC MEMORY

Park Lights Status LEDs Diagnostic Code

3 Flashes Series of 3 Flashes Door Opened “M” Models

3 Slow Flashes LEDs On Solid System is in Service Mode

4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units

5 Flashes Series of 5 Flashes Hood Pin Opened

5 Slow Flashes Series of 5 Flashes Ignition On During Start Attempt

6 Flashes Series of 6 Flashes Brake Pedal Shutdown

7 Flashes Series of 7 Flashes Tach Lock-Out

If the remote starter does not activate when the start button is pressed the park lights will

flash a diagnostic to indicate what shutdown input has been triggered.

Example when the start button is pressed the park lights flash 3 times slowly. Looking at

the chart below this would indicate that the system is in Service Mode.

LED Flashes Diagnostic

5 Flashes The system was shutdown by the hood pin input

6 Flashes The system was shutdown by the brake switch input

7 Flashes The system did not detect the tach signal

8 Flashes The system made 3 start attempts without starting

Page 10

OWNER’S GUIDE

REMOTE VEHICLE STARTER

Andere Handbücher für 1250 SERIES

Inhaltsverzeichnis

Andere Ultra Start Fernstartsystem Handbücher

Ultra Start

Ultra Start 80 Series Bedienungsanleitung

Ultra Start

Ultra Start 3295 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1250 SERIES Bedienungsanleitung

Ultra Start

Ultra Start PRO Series Bedienungsanleitung

Ultra Start

Ultra Start 1655XR Bedienungsanleitung

Ultra Start

Ultra Start 1500 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 15 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1175 Series Bedienungsanleitung

Ultra Start

Ultra Start 1172 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 22 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 15xx Bedienungsanleitung

Ultra Start

Ultra Start 3295Series Bedienungsanleitung

Ultra Start

Ultra Start 1172 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1155 Series Bedienungsanleitung

Ultra Start

Ultra Start RFK4BAM Bedienungsanleitung

Ultra Start

Ultra Start 22 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 90 Series Bedienungsanleitung

Ultra Start

Ultra Start 1172 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 25 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1600 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

Ultra Start

Ultra Start 1250 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 25 SERIES Bedienungsanleitung

Ultra Start

Ultra Start 1150 Series Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung