Ulvac GLD-040 Bedienungsanleitung

No.18400-2-03-13

Instruction Manual

for

Direct-Drive Oil Sealed Rotary Vacuum Pump

Model

GLD-040

Before using the product, be sure to read this manual.

Keep this manual in a place where it can be referred to at any time

and look after it carefully.

The contents of this instruction manual are subject to change

without prior notice due to improvements in performance and the

functions of the product.

ULVAC KIKO,Inc.

EC Declaration of Conformity

We,

ULVAC KIKO,Inc.

291-7 Chausubaru, Saito-city, Miyazaki, 881-0037. Japan

In accordance with the following Directive:

2006/42/EC

Machinery Directive

declare under our sole responsibility that the product,

Type of Product

Oil Sealed Rotary Vacuum Pump

Model Name

GLD-040,GLD-136A,GLD-137AA,

GLD-201A,GLD-202AA,GLD-280A,

GLD-136C,GLD-137CC,GLD-201B,

GLD-202BB, GLD-280B

to which this declaration related is in conformity with the following standards:

EN 1012-2:1996+A1:2009

Compressors and vacuum pumps –Safety requirements, Part2. Vacuum pumps

IEC/EN 61010-1:2010

Safety requirement for electrical equipment for measurement, control and

laboratory use - Part 1: General requirement

IEC/EN 60034-1:2010

Rotating electrical machines

following the provisions of

The person stated below will keep the following technical documentation:

operating and maintenance instructions

technical drawings

description of measures designed to ensure conformity

other technical documentation, e.g. quality assurance measures for design and production

Person authorized to compile the technical file:

( Name and address) Chris Goebel

ULVAC Gmbh

Parkring11,85748,Garching,Germany

06.Dec, 2017

Miyazaki , Japan

Tsuneo Osaka/

(date & place)

(name & signature)

- 01 -

0. Introduction

0.1 Before using the vacuum pump

Thank you for purchasing our vacuum pump (hereinafter called “pump”). When you have received

the pump, check that the delivered pump is as per your order and that it has not been damaged in

transportation, etc.

In order to use the pump for as long as possible, read this instruction manual

thoroughly before performing installation, operation, inspection and

maintenance, and sufficiently understand the cautions for safety, the

specifications and operation methods of the pump.

No part of this instruction manual may be copied for use by a third party

without our permission.

Warning

Note

- 02 -

0.2 Safety symbols

In this instruction manual and on warning labels attached to the pump, the following symbols

are used so that matters which must be strictly adhered to can be readily understood.

These symbols are divided as shown below.

When mishandled, there is an imminent danger of the operator suffering a fatal

accident or serious injury.

When mishandled, there is a possibility of the operator suffering a fatal

accident or serious injury.

When mishandled, there is a possibility of the operator suffering an injury

(light or medium injury) or of damage occurring to property.

When mishandled, there is a possibility of the pump being damaged or

malfunctioning.

The Inlet port of the pump

The exhaust port of the pump

Caution

Note

Warning

Danger

- 03 -

0.3 Cautions for safety

This pump is for dry air or the dry nitrogen suck only.

Never allow people other than repair engineers to disassemble or repair the

pump. Failure to do so may result in ignition or malfunction, leading to injury

or electric shock.

Connect the earth wire correctly. It is set up that a dedicated earth leakage

breaker should be installed. If the earth wire is not connected, there is

a possibility of electric shock occurring in the case of a malfunction or

electrical leakage.

There is a risk of explosion. Never block the outlet or operate the pump with

equipment mounted at the outlet side which blocks the passage of gas.

Otherwise, the internal pump pressure increases causing the pump to explode,

the oil level gauge to protrude or the motor to be overloaded.

This pump is not resistant to pressure. The internal pump pressure is limited

to 0.03 MPa (gauge pressure).

It gets an electric shock touching the motor energizing part. Please work after

pulling out the power plug without fail when wires electricity is connected,

it checks, and it transfers it.

Do not use the pump in an explosive atmosphere. Failure to do so will result

in injury or fire.

When shipping from the factory, the motor is set for 100-120V class. Do not

operate with 200-240V power supply voltage. In order to operate with 200-240V

class, the changeover switch in the terminal box must be changed into 200-240V

class as shown in fig.3.4“Electric wiring.”

Danger

Warning

- 04 -

Never touch the rotating section of the motor, shaft or coupling while the

pump is in operation. Failure to do so will result in injury.

Never place combustible materials around the motor or pump. There is a risk

of fire.

Also, do not place objects which block ventilation around the motor. Abnormal

heat generation may result in burns or fire.

Do not touch the motor while the pump is in operation or when the pump is

still hot immediately after it stops. Touching it will result in burns.

Arrange wires correctly in accordance with the “Electrical Equipment

Technical Standard” and “Wiring Regulations.” Incorrect wiring may result

in fire.

If the pump ceases operation or malfunctions, turn off the power switch

immediately to prevent accidents, and ask the company from which you purchased

the pump or the manufacturer for inspection and repair.

Do not operate the pump without adding pump oil. If it is operated in an

oil-less condition, the pump will be damaged.

Caution

Note

- 05 -

0.4 Acceptance and storage of the pump

0.4.1 Acceptance of the pump

Although the pump is delivered with great care, check the following after unpacking.

①The delivered pump is in accordance with your request.

②The specified accessories (enough pump oil to use the pump once; optional equipment) have

been provided.

③No parts have been damaged in transportation.

④Neither screws nor nuts have become loose nor were lost in transportation.

If there are any problems, contact the company from which you purchased the pump or the sales

department of the manufacturer.

0.4.2 Environmental conditions for storage, installation and operation

Since this pump is precisely engineered, ensure that the following conditions be satisfied during

storage, installation and operation.

①Ambient temperature, relative humidity: 7°C ~ 40°C, 85% RH or less

② Height above sea level during storage and installation: 1,000 m or less

③ Minimum required distances from the wall, 100mm

④ Other conditions for storage and operation

a）Free from corrosive and explosive gases

b）No condensation

c）Dust-free environment

d）Indoors

e）Do not place pumps on top of each other or place a pump on its side.

f）Not subject to direct sunlight

g）Far from heat sources

h）When you keep it for a long period of time, put pump oil into a pump and seal a inlet port

with a cap.

i）Don't keep it, where moisture is attracted.

Since the pump weighs as much as 16 kg, do not lift or transport it by yourself.

Doing so may cause an injury. Please wear safety shoes at the time of work.

Perform such work by two people as shown in 3.1 “Installation.”

Do not subject the pump to shocks or place the pump on its side. Doing so

may damage the pump.

For indoors use only.

Note

Caution

Note

- 06 -

0.5 Protective device

The pump is equipped with a single-phase 100-120 V (50/60 Hz) and 200-240 V (50/60 Hz)

motor.

This motor has a total of two overload protectors built in: one is of automatic reset type and the other

of manual reset type.

The automatic reset type thermal protector is intended to protect the motor when the pump is locked.

For details, refer to “4.6 Automatic Reset Type Thermal Protector.” The manual reset type thermal

protector is intended to protect the auxiliary coil.

For details, refer to “4.7 Manual Reset Type Thermal Protector.”

End-user has to make provisions for the installation of the over current protection of the power

circuit.

For the selection of an overload protector, refer to “3.4 Electric wiring.”

The automatic reset type thermal protector, one of the overload protectors in

this motor, will automatically reset itself after it has functioned.

This motor houses an automatic returning thermal protector, which may be

activated in case of trouble. The motor will restart automatically when the

temperature goes down to 78 ± 5℃.

If the thermal protector is activated, pulled out the power plug immediately

for safety reason.

Use the pump only at the rated voltage. Use at other than the rated voltage

will interfere with correct operation of the overload protector, and result

in the motor burning out, or fire.

Note

Caution

Contents - 1

Contents

0. Introduction ·························· 01

0.1 Before using the vacuum pump ·························· 01

0.2 Safety symbols ·························· 02

0.3 Cautions for safety ·························· 03

0.4 Acceptance and storage of the pump ·························· 05

0.4.1 Acceptance of the pump ·························· 05

0.4.2 Environmental conditions for storage, installation and operation ·· 05

0.5 Protective device ·························· 06

1. For Safe Operation ·························· 1

1.1 Hazards peculiar to the pump and safety measures ······················· 1

1.1.1 Danger Leakage of hazardous gases and substances ············ 1

1.1.2 Warning Electric shock ·························· 1

1.1.3 Warning Explosion ·························· 2

1.1.4 Caution High temperature ·························· 2

1.2 Safety Data Sheet (SDS) ·························· 2

2. Outline of the Pump ·························· 3

2.1 Specification ·························· 3

2.2 Dimensional drawing ·························· 4

3. Installation ·························· 5

3.1 Installation ·························· 5

3.2 Lubrication ·························· 6

3.3 Vacuum piping ·························· 7

3.4 Electric wiring ·························· 8

3.5 Fluctuation in the power voltage and frequency ························· 10

4. Operation ·························· 11

4.1 Cautions for operation ·························· 11

4.2 Start of operation ·························· 12

4.3 Stopping the operation ·························· 12

4.4 Operation in cold climates ·························· 13

4.5 Backflow preventer ·························· 13

4.6 Automatic reset type Thermal protector ·························· 14

4.7 Manual reset type Thermal protector ·························· 14

4.8 Gas ballast valve ·························· 16

4.9 Installation of the oil mist trap (Option) ·························· 17

4.10 Restriction on operation when the oil mist trap is installed ········· 17

Contents - 2

5. Pump Performance ·························· 18

5.1 Ultimate pressure ·························· 18

5.2 Pumping speed ·························· 18

5.3 Power requirement ·························· 18

6. Maintenance, Inspection and Repair ·························· 20

6.1 Maintenance ·························· 20

6.2 Periodic inspection ·························· 20

6.3 Replacement of the pump oil ·························· 22

6.4 Replacement of the coupling spider ·························· 24

6.5 Trouble check list ·························· 25

7. Disposal ·························· 27

8. Maintenance parts ·························· 28

8.1 Maintenance parts list ·························· 28

8.2 Disassembly drawing ·························· 29

Warranty

Safety Data Sheet (SDS)

Pump Usage Check Sheet (Use this sheet for requesting an overhaul.)

Sales and Service Centers

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ulvac Wasserpumpe Handbücher

Ulvac

Ulvac UTM-MS Series Bedienungsanleitung

Ulvac

Ulvac DIS-251 Bedienungsanleitung

Ulvac

Ulvac UTM1600 Series Bedienungsanleitung

Ulvac

Ulvac TM-2 Bedienungsanleitung

Ulvac

Ulvac ULK-10A Bedienungsanleitung

Ulvac

Ulvac DAL-181D Bedienungsanleitung

Ulvac

Ulvac MBS-053 Bedienungsanleitung

Ulvac

Ulvac G-20DA Bedienungsanleitung

Ulvac

Ulvac GLD-051 Bedienungsanleitung

Ulvac

Ulvac DAT-50DA Bedienungsanleitung

Ulvac

Ulvac PVD-180 Bedienungsanleitung

Ulvac

Ulvac CRYO-U Series Bedienungsanleitung

Ulvac

Ulvac GCD-051X Bedienungsanleitung

Ulvac

Ulvac DTC-41 Bedienungsanleitung

Ulvac

Ulvac CRYOPUMP CRYO-U Series Bedienungsanleitung

Ulvac

Ulvac VD151 Bedienungsanleitung

Ulvac

Ulvac PMB100D Bedienungsanleitung

Ulvac

Ulvac GHD-101A Bedienungsanleitung

Ulvac

Ulvac PKS-030 Bedienungsanleitung

Ulvac

Ulvac GR60 Bedienungsanleitung

Ulvac

Ulvac DOP-80SP Bedienungsanleitung

Ulvac

Ulvac DTC-22 Bedienungsanleitung

Ulvac

Ulvac DAU-100 Bedienungsanleitung

Ulvac

Ulvac DOP-200S Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung