Uniden B6440D Bedienungsanleitung

SET UP GUIDE

Wired Video Security DVR System

Irving, Texas Printed in China

This Set Up Guide applies to the following models:

B6440D

G6440D

G6840D1

G6860D2

G6880D2

Uniden surveillance products are not manufactured and/or sold with the intent to be used for

illegal purposes. Uniden expects consumer’s use of these products to be in compliance with all

local, state and federal law. For further information on video surveillance and audio recording legal

requirements, please consult your local, state and federal law.

All rights allowed by law are hereby reserved.

Information in this document is subject to change without notice.

ABOUT YOUR VIDEO SECURITY SYSTEM

Thank you for purchasing Uniden's Guardian Video Security DVR. This state of the

art surveillance system provides high quality synchronous audio and video. TCP/IP

network technology lets you monitor and operate your system remotely.

This Setup Guide provides basic setup and operation information so you can quickly

get your system up and running. It also sets up remote viewing access. Download

the Owner’s Manual from www.uniden.com for detailed information about system

operation.

INCLUDED IN THE BOX:

• Cameras (4, 6, or 8) • Receiver (1) • 12V 2A Power Adapter

(2)

• 4-or8-WaySplier

Cable

• 60’ExtenonCable(4,

6, or 8)

• USB Mouse

• Ethernet Cable • HDMI Cable • CameraMounngKit

If any items are missing or damaged, visit www.uniden.com for assistance

SETTING UP YOUR SYSTEM - BASIC

Images in these installation procedures show the front and back panels of the

G6840D1. Other models' back panels will be different, but similar.

Basic setup connects the DVR to all peripheral equipment (cameras, mouse,

monitor, etc) and power. Once connected, your system is ready for use through the

DVR’s menu system.

You can set up your system in 2 stages - installing your system hardware and then

sengupbasicconguraon.Eachstagehasseparatesteps.

STAGE 1 - Install System Hardware

• Connect DVR to Power

• Connect Mouse to DVR

• Connect DVR to Monitor

• Connect Ethernet Cable

• Connect Cameras to DVR and Power

• Install Cameras

STAGE 2 - Basic System Configuration

• Complete Wizard and Log In

• Set Password

• Set Screen Resolution

• Set Motion Sensitivity

CONNECT DVR TO POWER

1. Connect the DVR to 12V power using the 12V

2A power adapter (supplied).

2. Connect the power adapter to the surge protector plugged into 120V indoor

power.

CONNECT MOUSE TO DVR

Connect the mouse to the DVR at the labeled USB

port on the back of the DVR.

CONNECT DVR TO MONITOR

There are three different ways to connect the DVR and monitor, depending on

what type of monitor port connection is available.

Monitor with HDMI Port

1. Connect DVR and monitor

using HDMI Cable

(included).

HDMI cable to DVR HDMI cable to Monitor

(example)

2. Connect monitor to surge protector plugged into 120V indoor power.

3. TheDVRbeepsasitpowersup.AertheUNIDENwelcomescreendisplays,

the Wizard screen displays.

4. Select Exit for now; we will return to the Wizard later in the setup process.

Monitor with VGA Port

1. Connect DVR and monitor

using VGA Cable (not

included).

VGA cable to DVR VGA cable to

Monitor (example)

2. Connect monitor to surge protector plugged into 120V indoor power.

3. TheDVRbeepsasitpowersup.AertheUNIDENwelcomescreendisplays,

the Wizard screen displays.

4. Select Exit for now; we will return to the Wizard later in the setup process.

TV with BNC Port (VIDEO IN)

1. Connect DVR and TV using

BNC-RCACable(notincluded).

BNC-RCAcabletoDVR BNC-RCAcableto

Monitor (example)

2. Connect TV to surge protector plugged into 120V indoor power.

3. TheDVRbeepsasitpowersup.AertheUNIDENwelcomescreendisplays,

the Wizard screen displays.

4. Select Exit for now; we will return to the Wizard later in the setup process.

CONNECT ETHERNET CABLE

Connect one end of the Ethernet cable to the RJ45 jack on the DVR and the other to

yourethernetconnecondevice(router,cablebox,etc).

CONNECT CAMERAS TO DVR AND POWER

Eachcameraconnectstooneendofthe60footextenoncable.Theotherendof

thecableconnectstothereceiverandtopower.Theendsoftheextenoncable

are marked for Camera or DVR side

1. Connect camera cable's blue end

(male)tothebluecamera-sideBNCend

(female) of the extension cable.

Male Female

Female Male

2. Connect the camera cable’s RED power

connector (female) to the DVR extension

cable’s RED power connector (male).

3. Connect the extention cable's other

blueBNCend(female)toDVR'sVideoIn

connector (male).

The Video In ports on the back of the DVR

are numbered. Do not connect cameras to

ports that your system does not support. If

you have 1 - 4 cameras, use ports labeled

1 - 4, etc.

4. Connecttheextenoncable’sred

(female) power connector to one of the

powerspliercableends(male).

5. Repeat these steps to connect the other cameras to the DVR and to the split-

ter cable.

6. Connectthepowerspliercabletothe

power adaptor.

Female

Male

7. Plug power adaptor into the surge protector. Live video from the cameras

displays on the screen.

Some DVR systems have more than 4 cameras. DVR systems with 6 or 8 cameras

have an 8x splier.

INSTALL CAMERAS

Video surveillance laws vary from state to state. Check local regulations to be

sure you are operating in a legal manner.

Installaon Tips

• When selecting an outside location for your cameras, keep in mind that most

cameras are designed to operate between 14°F to 122°F (-10°C to 50°C) with a

relative humidity of up to 95%. Avoid installing cameras in direct sunlight, and

consider wind chill and other environmental factors, too.

• Mount the camera in an area that is visible, but out of reach. Route the wiring

so it does not interfere with power or telephone/cable lines and it should not

be where it could be easily cut. Create a plan for camera wire routing and for

camera angle.

• Adjust the camera angle so that it covers an area with high traffic as needed.

In “high-risk” locations, have more than one camera cover the same area. This

provides camera redundancy if a vandal attempts to damage a camera.

Male

Female

• If you position cameras indoors, avoid pointing the camera at a glass window

to see outside. This may result in a bright white ring in the night vision image

because the light from the night vision LEDs may reflect off the window glass.

Take the following placement suggestions under consideration:

• Cabling Distance From DVR to Camera. The video signal sent from the camera

to the DVR is reduced over distance. The maximum distance allowed is 330

feet (100 meters). A 60 foot cable is included. If you need a cable longer than

60 feet, then use an RG59 cable (with suitable connectors).

• Do not submerge any camera.

• Mounting. Ensure the camera is mounted on a stable surface which is capable

of supporting 5 times the weight of the camera.

• Avoid direct exposure to the weather. Cameras which are weatherproof may

be mounted outside, such as under an eave or other overhang; however, the

image will be affected by rain, etc., landing on the lens. Do not allow direct

sunlight to land on the lens.

1. With the DVR connected to the camera, hold it in the location where you

want it mounted. Check the display on the monitor to verify that the view

from that location is acceptable.

2. Mount the camera(s) to the desired surface using the parts in the supplied

mounting kit. If mounting on drywall, use the drywall anchors supplied in

the kit.

3. Adjust the camera stand to ensure that the camera has a satisfactory view

of the area you would like to monitor. The camera has several adjustment

points to provide maximum flexibility when setting the view angle. Use a

Philip's head screwdriver (not included), to make any adjustments.

BASIC CONFIGURATION

Basic configuration lets you use the DVR's internal menu system to access all DVR

features. The easiest way to get started is to go through the Wizard quick setup and

then fine tune specific areas (such as screen resolution, etc.).

Some fields may require keyboard input. Select the field and a pop-up keyboard

displays. This keyboard supports alphanumeric and symbol keys. Shift once to

input a capital letter; shift again to return to lower case. Click

ESC

to close the

keyboard.

POWER ON AND ACCESS WIZARD

1. If your DVR is already connected to power, disconnect it. Reconnect the DVR

to the power supply; the DVR powers up and the POWER and HDD LEDs on

the front light up.

2. AertheDVRpowersupandthe

UNIDENwelcomescreendisplays,the

rstofthreeWizardscreensdisplays.Fill

inthedateandmeinformaon.The

mostcommonlyusedmezonesforthis

system are:

• GMT-05:00 - Eastern Standard (Default)

• GMT-06:00 - Central Standard

• GMT-07:00 - Mountain Standard

• GMT-08:00 - Pacific Standard

• GMT-09:00 - Yukon Standard

• GMT-10:00 - Alaska-Hawaii Standard

3. Select Next.

4. The second Wizard screen sets up

DVR monitoring through the internet.

SettheHpPortto8091andthe

server port to 5000. Click Obtain an IP

address automacally to get network

informaonorllintheeldsmanually.

Refer to the Owner’s Manual at www.

uniden.com for internet access details.

Click Next.

8091

5. The last Wizard screen displays storage

status.Reviewtheinformaonandthen

click FinishtosavetheWizardseng.

Live video displays.

You need to log into the system to continue setting it up.

1. Right-click on any Live View screen; a

menu shortcut screen displays.

2. Select Main Menu; the Login dialogue

box displays. The user name, admin, is

already entered. There is no password

required so select Login (set a password

aeryoulogin).

NOTE: Uniden strongly recommends that

you set a password for your system.

3. The Main Menu screen displays.

SET PASSWORD

1. From the Main Menu screen, select

Setup>Users. The User Management

screen displays.

2. Select Change Password. (At this point,

there are no other users added to the

system.) In the Change Password screen,

enteranewpasswordandconrmit

usingthepopupkeyboard,selecng

Enter each time. Select OK to save the

new password.

3. The User Management screen displays

again.

4. Click EXIT to return to the Setup screen.

SET MOTION SENSITIVITY

You can set how sensitive the camera should be for movement to trigger recording.

You can also block off (mask) certain areas of the camera's viewing window so

normal movement in those areas (trees, wind chimes, etc.) won't trigger recording.

1. From the menu shortcut screen, select

Main Menu/Setup/Alarm/Moon. The

Moon screen displays.

2. Seteachcamera’smoondeteconspecicaons.

• Select Camera. Select the channel you want to record when motion is

detected.

• Select Holding Time. Set how long the camera continues recording after

motion is no longer detected.

• Select Trigger. Other channels record when one of the cameras detects

motion. The Trigger field sets how that camera notifies that it is recording

(buzzer, email notification, etc).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Uniden Sicherheitssystem Handbücher

Uniden

Uniden UDVR45x4 Bedienungsanleitung

Uniden

Uniden UDW20553 Benutzerhandbuch

Uniden

Uniden UWS1113 Bedienungsanleitung

Uniden

Uniden GSHC1000 Series Bedienungsanleitung

Uniden

Uniden Guardian G455 Bedienungsanleitung

Uniden

Uniden GDVR 42 Series Bedienungsanleitung

Uniden

Uniden Guardian G455 Bedienungsanleitung

Uniden

Uniden G37 Series Bedienungsanleitung

Uniden

Uniden GUARDIAN G766 Bedienungsanleitung

Uniden

Uniden GDVR 10 Series Bedienungsanleitung

Uniden

Uniden G17xx Series Bedienungsanleitung

Uniden

Uniden UDW-10003 Bedienungsanleitung

Uniden

Uniden Guardian B6440D1 Bedienungsanleitung

Uniden

Uniden UDW10055 Bedienungsanleitung

Uniden

Uniden GnVr 85XX series Bedienungsanleitung

Uniden

Uniden UDW10055 Service-Handbuch

Uniden

Uniden UDW20553 Service-Handbuch

Uniden

Uniden G14xx Series Bedienungsanleitung

Uniden

Uniden BC6440D Bedienungsanleitung

Uniden

Uniden wdvr42hdd Bedienungsanleitung

Uniden

Uniden G17xx Series Bedienungsanleitung

Uniden

Uniden GDVR 4A Series Bedienungsanleitung

Uniden

Uniden Guardian G455 Bedienungsanleitung

Uniden

Uniden G2701 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung