Uniden UH043SX-2NB Bedienungsanleitung

UH043SX-2NB

UHF CB Transceiver

For more exciting new products please visit our website:

Australia: www.uniden.com.au

New Zealand: www.uniden.co.nz

Controls & Indicators

Included in your Package

• UH043SX-NBRadio(2)

• OperatingGuide

• BeltClip(2)

• ChargingCradlewithACAdaptor

• NiMHBatteryPack(2)

• VOXHeadset(2)

1 Antenna

2 PTT(Push-To-Talk)Key

3 MonitorKey

4 Keylock/CallKey

5 Memory/ScanKey

6 Channel/PowerHi-LoKey

7 Speaker

8 HeadsetJack

9 Select/PowerOn-OffKey

10 Volume/SelectUpKey

11 Volume/SelectDownKey

12 Microphone

13 ReceiveIndicator

14 TransmitIndicator

15 ChannelIndicator

16 DCSONIndicator

17 ScanIndicator

18 MemoryIndicator

19 PriorityChannelIndicator

20 CTCSSONIndicator

21 BatteryLevelIndicator

22 HITransmitIndicator

23 LoTransmitIndicator

24 CTCSSandDCSCode/Volume

 LevelIndictor

25 VolumeSettingIndicator

26 VOXIndicator

27 BusyChannelLockoutIndicator

28 KeypadLockIndicator

29 ChargingLEDs

1UHFCBTransceiverUNIDENUH043SX-2NB

Optional Accessories

• VOXEarset

• CarryCase

• SpeakerMic

Getting Started

NOTE

Unidendoesnotrepresentthisproducttobewaterproof.

DonotexposethisproducttoRainorMoisture.

Battery Installation

YourUH043SX-2NBunitusestheincludedNiMHbatterypackforpower.

Theunitcanbepoweredwithoptional4AAAALKALINEbatteries.

NOTE

Ifyoudon’tusetheUH043SX-2NBforlongperiods,Uniden

recommendremovingthebatteries.TheUH043SX-2NBis

designedtoretaintheprevioususersettings.Thisfeature

willcontinuetouseasmallamountofbatterypowerwhile

theunitisswitchedoff.

OLD

NEW

Toavoiddamagetotheunitdonotmixoldandnew

batteries.

To install the batteries:

1. Makesureyourradioisoff.

2. Releasethebatterycoverclip,thenremovethe

  batterycover.

3. InsertNiMHbatterypackaccordingtothe

  orientationonthebatterypack.

  Insert4AAAALKALINEbatteries(notincluded)

  accordingtothepolaritysymbolsinsidethe

  batterycompartment.

4. Alignthebatterycovertabswiththe

  UH043SX-2NBtabholesthenreplacethecoverclip.

NOTE

Donotchargealkalineornonrechargeablebatteries.

2UHFCBTransceiverUNIDENUH043SX-2NB

Getting Started

3UHFCBTransceiverUNIDENUH043SX-2NB

Installing the Charge Cradle

1. PlugtheACadaptorintotherearofthechargecradleandintothe

  mainspower.

2. PlacetheUH043SX-2NBintothechargecradle.Thechargelightwill

  comeontoindicatetheunitischarging.

3. BeforeoperatingtheUH043SX-2NB,chargethebatterypackfor

  16hours.

NOTE

Donotchargealkalineornonrechargeablebatteries.

User License Information

NOTE

ThecitizenbandradioserviceislicencedinAustraliaby

ACMARadio-communications(CitizenBandRadio

Stations)ClassLicenceandinNewZealandbyMED

GeneralUserLicenceforCitizenBandRadioandoperation

issubjecttoconditionscontainedinthoselicences.

Getting Started

Belt Clip

To attach the belt clip:

Slidethebeltclipuntilitsnapsintoplace.

To remove the belt clip:

Toremovethebeltclip,pressandhold

beltcliplocker,slidethebeltclipatthe

sametimeuntilreleased.

Low Battery Alert

Ifthebatterylevelbecomeslow,thebattery

indicatoricononthedisplaybeginsashing.

Whenthebatteriesintheunitarelow,theunit

willgointoabatteryLowmode.TheTransmit

modeisdisabled.Replacethealkaline

batteriesimmediatelyorifyouareusingthe

NiMHbatterypack,placetheradioonthe

chargecradletorecharge.Fullchargewilltake

upto16Hrs.

Back Light

TheUH043SX-2NBhasanautomaticdisplaybacklightwhichremainson

for10secondsafterakeypress(allkeysexceptPTTkey).Thebacklight

willworkevenifthekeypadislockedbutwillnotworkduringlowbattery

alertmode.

4UHFCBTransceiverUNIDENUH043SX-2NB

BeltClipLocker

Operation

5UHFCBTransceiverUNIDENUH043SX-2NB

Power On/Off

1. PressandholdSELECT/ keytoturntheradioon.

  Achannelnumberwillappearonthedisplay.

2. PressandholdSELECT/ keytoturntheradiooff.

Volume

Press or keytoincreaseordecreasethe

volumelevel.‘VOL’iconappearsonthedisplay

whilevolumeisbeingadjusted.

Thereare8volumelevels.Level0(NoAudio)to

Level7(MaximumVolume).

Adjusting the Key Beeps

Yourradioemitsabeepeachtimeoneofthekeys

(exceptforthePTTkey)ispressed.

1. ToturnOFFthisbeep:Pressandhold /CALLkeywhileturning

  ontheradio.

2. ToturnONthisbeep:Pressandhold /CALL keywhileturning

  ontheradio.

Roger Beep

RogerBeepisaBEEPthatissenttonotifytheendoftransmission(bothPTT

andVOXtransmission.)RogerBeepcanbeheardthroughthespeakerwhen

KeyBeepison.RogerBeepistransmittedevenifKeyBeepisturnedoff.

However,RogerBeepwillnotbeheardfromthespeaker.

1.ToturnOFFRogerBeep:Pressandhold keywhileturningontheradio.

2.ToturnONRogerBeep:Pressandhold keywhileturningontheradio.

Keylock On/Off

1.Press /CALL keyfor1.5secondstoenterkeylockonmode.

2.Press /CALL keyfor1.5secondswhileinKeylockmodetoexit

 theKeylockmode.

NOTE

WhileinKeylockonmode,theUH043SX-2NBcanstill

receiveandtransmit.

Operation

6UHFCBTransceiverUNIDENUH043SX-2NB

Selecting a Channel

1. PressCH / HI / LOkeymomentarilytoactivatechannel

  selectmode.Thedisplayedchannelwillash.

2. Press or keytoselectthedesiredchannel.

NOTE

Refertochannelguidelinesonpage13.

ForAustralia,Channels05and35are

reservedforEmergencyCalls.

3. PressCH / HI / LOkeymomentarilytoexitchannel

  selectmode.Ifnokeyispressedwithin5secthe

  UH043SX-2NBwillexitfromthechannelselectmode.

To Transmit and Receive

TheUH043SX-2NBusestheUHF-CBChannels

(Channels 22 and 23 are for telemetry and

telecommand applications. Transmit is

inhibited on these channels).

1. Beforeyoutransmit,listenforactivityonthe

  selectedchannel.

2. Whenthechannelisclear,pressandholdthePTTkeytotransmit.

TXiconappearsonthedisplay.

Holdtheradiowithmicrophoneapproximately5cminfrontofyourmouth

withtheantennaatapproximately45°angleawayfromyourhead.Speak

inaclear,normalconversationalvoice.

3. Whenyouhavenishedspeaking,releasethePTTandlistenfora

  response.TX iconthendisappearsonthedisplay.Whilereceiving,

theRX iconisdisplayed.

Transmit Hi/Lo Power Select

PressandholdCH / HI / LOkeytoselectdesiredtransmit

level.HI iconwillappearonthedisplayformaximum

transmitlevel.LO iconwillappearonthedisplayfor

minimumtransmitlevel.TheRFtransmitpowerofthe

UH043SX-2NBisselectablebetween0.7/0.5W.

Operation

Automatic Squelch Feature

TheUH043SX-2NBisequippedwithanAutomaticSquelchSystem

whichshutsoffweaktransmissionsandunwantednoise.

Monitor

Thisfeatureenablesuserstolistenforweaksignalsonthecurrent

channelatthepressofakey.

To use monitor

1. PressMONkey.TheRX iconwillash.

2. Releasewithin1.5secondsandtheunitexits

  Monitormode.

3. PressandholdMON keyfor2secondsforcontinuouslistening.

  Thereceivercircuitwillstayopen,lettinginboththenoise&weak

  signals.TheRX iconashesinthisstatus.

4. ToreturntonormalReceivemodepressMONkey.TheRX icon

  disappearsorstopsashinginthisstatus.

Scanning

ThescanfunctionscansallchannelswhicharestoredintheSCAN

CHANNELMEMORYandstopsatanactivechannel.IfaPRIORITY

channelhasbeenselectedthenthischannelwillbemonitoredforactivity

every3seconds.Whenthesignalstops,theUH043SX-2NBwaits

2seconds(ReplyDelay)beforescanningresumes.

To initiate scanning;

1. PressMEM / SCNkeymomentarilytobegin

  scanning.

  TheSCANiconisdisplayed.

2. PressSELECT / ,MEM / SCN , /CALL

  orPTTkeytocancel.

Whenscanstopsatabusychannel,pressing

CH / HI / LOkeywillresumescan.

7UHFCBTransceiverUNIDENUH043SX-2NB

Operation

Reply Delay

Whilescanning,theUH043SX-2NBstopsatabusychannelandreceives

atransmission.Whenthereceivedsignalisover,theunitwillwaitfor2

secondsforthereturnofthesignal,otherwise,theradioresumesscanning.

To Operate in Duplex Mode (Repeaters)

TheDuplexfunctionenablesyoutoaccesslocalrepeaterstations.You

canonlyactivateDuplexfromCH01-CH08andCH41-CH48.

UHFCBRepeatersareusedtoretransmitorrelayyoursignal.Repeaters

willextendtherangeofyourradioandovercometheshieldingeffect

causedbysolidobstructions.

NOTE

Contactyourretailerforalistofrepeatersavailableinyour

area.

Operation With the Aid of a Repeater

1.PressSELECT / keysixtimes. appearsonthedisplay.

2.Press or tochange to forCH01-CH08and to for

 CH41-CH48.

3.PressSELECT / toconrm

Todeactivatetheduplexoperationrepeatactivationprocessandchange

to or to .UH043SX-2NBwillreturntonormaloperation.

NOTE

If or ispressedwhenthechannelisnotfrom

CH01-CH08orCH41-CH48,anerrortonesounds.

8UHFCBTransceiverUNIDENUH043SX-2NB

Operation

CTCSS & DCS

(Continuous Tone Coded Squelch System) & (Digital Coded Squelch)

CTCSSisafeaturethatallowsagrouptotalktoeachother

withouthearingotherusersonthesamechannel.

1. PressSELECT / keymomentarilytoenterCTCSS

  mode.ThecurrentselectedCTCSStoneashes.

2. Press keytoselecttherequiredCTCSS

  tone(OFFor1-38).

3. PressSELECT / keysixtimestoconrmthe

  selectedsettingandexittostandbymode.

ForchannelswithaCTCSStonesetting,theCTCSStoneisdisplayed

belowthechannelindicator.ForchannelswiththesettingofCTCSS

OFF,therewillbenodisplaybelowthechannelindicator.

DCSisadigitalextensionofCTCSS.Itprovides104extra,digitally

coded,squelchcodesthatfollowafterthe38CTCSScodes.CTCSS

1-38,followedbyDCS1-99plusDCS100-104(representedbyo0-o4on

thedisplay).

1. PressSELECT / keymomentarilytoenterCTCSS/DCSmode.

2. Use keytoselectaDCScode.TheDCScodes

  followonaftertheCTCSScodes.TheDCSiconwill

  replacetheCTCSScodeonthedisplay.

3. PressSELECT / keysixtimestoconrmthe

  selectedsettingandexittostandbymode.

  TheDCSiconwillappearwhenselected.Toturn

  offDCSselectCTCSSOFFandnodisplaywillshow

  belowthechannelindicator.

NOTE

Channels05and35areusedforemergencychannels.

CTCSSandDCSwillnotoperateonthesetwochannels.

9UHFCBTransceiverUNIDENUH043SX-2NB

Inhaltsverzeichnis

Andere Uniden Transceiver Handbücher

Uniden

Uniden Remote VFO 8010 Bedienungsanleitung

Uniden

Uniden Benjamin Bedienungsanleitung

Uniden

Uniden X66 Bedienungsanleitung

Uniden

Uniden UH5060VP Bedienungsanleitung

Uniden

Uniden UH7700NB Bedienungsanleitung

Uniden

Uniden UH089NB Bedienungsanleitung

Uniden

Uniden 2080 Bedienungsanleitung

Uniden

Uniden UH8010NB Bedienungsanleitung

Uniden

Uniden UH7760NB Bedienungsanleitung

Uniden

Uniden UH5040 Bedienungsanleitung

Uniden

Uniden UH755 Series Bedienungsanleitung

Uniden

Uniden UH037SX-2NB Bedienungsanleitung

Uniden

Uniden UH305SX-2NB Bedienungsanleitung

Uniden

Uniden UH950S Bedienungsanleitung

Uniden

Uniden UH037SX-2NB Bedienungsanleitung

Uniden

Uniden Sundowner UH-100 Bedienungsanleitung

Uniden

Uniden ATLANTIS250 BK - ATLANTIS 250 VHF Radio Service-Handbuch

Uniden

Uniden UH850S Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Uniden

Uniden UH9080 Bedienungsanleitung

Uniden

Uniden MHS245 Bedienungsanleitung

Uniden

Uniden UH076DLX Bedienungsanleitung

Uniden

Uniden UH078SX-NB Bedienungsanleitung

Uniden

Uniden Sundowner UH-077 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung