Uniden UH039P Bedienungsanleitung

UH039P

Operating Guide

To bring outstanding wireless communication products

to people's lives throughout the world.

volume

channel/

scan

dup mon

hi/lo

volume

channel/

scan

dup mon

hi/lo

CONTROL & INDICATORS

1 Antenna

2 PTT (Push-To-Talk) Button

3 Channel/scan up Key

4 Channel/scan down Key

5 Duplex/Transmit Hi/Lo

6 Speaker

7 Power On/Off/Select Key

8 Monitor Key

9 Volume up Key

10 Volume down Key

11 Battery Compartment Door

INCLUDED IN YOUR PACKAGE:

UH039P Radio (2)

Operating Guide

Belt Clip (2)

Charging Cradle with

AC Adaptor

NiMH Battery Pack (2)

12 Channel Indicator

13 Receive Indicator

15 Transmit Indicator

Battery Indicator

16 Scan Indicator

17 Vox on Indicator

18 Key lock setting Indicator

19 Volume setting Indicator

20 Duplex Indicator

21 TX Hi Indicator

22 CTCSS Channel Indicator

RX TX

VOL

DUP

SCAN

VOX

1413 15

volume

channel/

scan

dup mon

VOX Earset

VOX Headset

Carry Case

OPTIONAL ACCESSORIES

RX TX

VOL

DUP

SCAN

VOX

hi/lo

Your UH039P unit uses the included NiMH battery pack for

power. The unit can be powered with optional 4 AAA ALKALINE

batteries.

GETTING STARTED

To avoid damage to the unit do not mix

old and new batteries.

To install the batteries:

1. Make sure your radio is off.

2. Remove the battery compartment

door by pressing the tab at the bottom

of the compartment door, allowing the

door to be removed.

3. Insert NiMH battery pack according to

the orientation on the battery pack.

OR Insert 4 AAA ALKALINE batteries (not

included) according to the polarity

symbols inside the battery

compartment.

4. Replace the battery cover.

BATTERY INSTALLATION

Uniden does not represent this product to be

waterproof. Do not expose this product to Rain

or Moisture.

INSTALLING THE CHARGE CRADLE

!Plug the AC adaptor into the rear of the charge cradle and

into the mains power.

Do not charge alkaline or non

rechargeable batteries.

OLD

NEW

If the battery level becomes low, the battery

indicator icon on the LCD begins flashing.

LOW BATTERY ALERT

When the batteries in the unit are low, the unit will go into a

Battery Low mode. The Transmit mode is disabled. Replace

the alkaline batteries immediately or if you are using the NiMH

battery pack, place the radio on the charge cradle to recharge

to continue using the radio.

To attach the belt clip:

To remove the belt clip:

Slide the belt clip until it snaps into place.

To remove the belt clip, press and hold

belt clip locker, slide the belt clip at the

same time until released.

BELT CLIP

Belt Clip Locker

Place the UH039P into the charge cradle. The charge light will

come on to indicate the unit is charging. Before operating the

UH039P, charge the battery pack for 16 hours.

Power Point

charge 1 charge 2

volume

channel/

scan

dup mon

Do not charge alkaline or non

rechargeable batteries.

OPERATION

volume

channel/

scan

dup mon

VOL

hi/lo

VOLUME

Press volume or to increase or

decrease the volume level.

icon appears on the display while

volume is being adjusted.

There are 8 volume levels. Level 0 (No

Audio) to Level 7 (Maximum Volume).

'VOL'

POWER ON/OFF

Press and hold to turn the radio on. A

channel number will appear on the display.

Press and hold to turn the radio off.

ADJUSTING THE KEY BEEPS

Your radio emits a beep each time one of the keys (except for

the PTT button) is pressed.

Press and hold while turning on

the radio.

Press and hold while turning on the

radio.

To turn this beep:

OFF

dup

ROGER BEEP

Roger Beep is a BEEP that is sent to notify the end of

transmission (both PTT and VOX transmission.) Roger Beep can

be heard through the speaker when Key Beep is on. Roger Beep

is transmitted even if Key Beep is turned off. However, Roger

Beep will not be heard from the speaker.

Press and hold channel/scan

while turning on the radio.

Press and hold channel/scan

while turning on the radio.

To turn Roger Beep:

OFF

SELECTING CHANNEL

Press channel/scan or to select

the desired channel.

TO TRANSMIT AND RECEIVE

The uses the 40 UHF-CB Channels. For your

reference a list of the available channels and corresponding

frequencies is printed on page 10.

UH039P

1. Before you transmit, listen for

activity on the selected channel.

2. When the channel is clear, press

and hold the to transmit.

appears on the LCD.'TX'

PTT

volume

channel/

scan

dup mon

hi/lo

volume

channel/

scan

dup mon

hi/lo

PTT

Switch

3. When you have finished speaking, release the and

listen for a response. then disappears on the LCD.

While receiving, the icon is displayed.'RX'

'TX'

PTT

Hold the radio with microphone approximately 5 cm in

front of your mouth with the antenna at approximately 45°

angle away from your head. Speak in a clear, normal

conversational voice.

AUTOMATIC SQUELCH FEATURE

The is equipped with an Automatic Squelch System

which shuts off weak transmissions and unwanted noise.

UH039P

TRANSMIT Hi/Lo SELECT

Press and hold for 2 seconds when the

unit is in Transmit Lo and it will switch to

Transmit Hi. icon will appear on

display.

Press and hold for 2 seconds again to

return to Transmit Lo setting. icon will

disappear from display.

The RF transmit power of the is

selectable Transmit Power 0.3/0.7 W.

'HI'

UH039P

dup

MONITOR

This feature enables users to listen for weak

signals on the current channel at the press of

a button.

To use monitor:

Press . The icon will flash once.

Release within 1.5 seconds and the unit exits Monitor

mode.

Press and hold for 2 seconds for continuous listening.

The receiver circuit will stay open, letting in both the noise

& weak signals. icon flashes in this status.

To return to normal Receive mode press . icon

disappears or stops flashing in this status.

'RX'

mon

DUP

dup

Press momentarily. The icon

appears.

Press again to deactivate the duplex

operation. will return to normal

operation.

'DUP'

UH039P

If is pressed when the channel is not from

CH01 - CH08, an error tone sounds.

TO OPERATE IN DUPLEX MODE (REPEATERS)

The Duplex function enables you to access local repeater

stations. You can only activate Duplex from CH01-CH08.

UHF CB Repeaters are used to retransmit or relay your signal.

Repeaters will extend the range of your radio and overcome

the shielding effect caused by solid obstructions.

Operation with the aid of a Repeater

Contact your retailer for a list of repeaters

available in your area.

Channels 5 and 35 are used for emergency channels.

CTCSS will not operate on these channels.

CTCSS (Continuous Tone Coded Squelch System)

CTCSS is a feature that allows a group to talk to each other

without hearing other users on the same channel.

Press momentarily in Stand By mode to enter CTCSS

mode.

The current selected CTCSS tone flashes in the CTCSS channel

indicator.

Press channel/scan or to select the required CTCSS

tone (OFF or 1-38).

For channels with a CTCSS tone setting, the CTCSS tone is

displayed in the CTCSS channel indicator. For channels with

the setting of CTCSS OFF, there will be no display in the CTCSS

channel indicator.

Press three times momentarily to confirm the selected

setting and exit to standby.

SCANNING

The scan function scans all channels and stops at an active

channel. When the signal stops, the waits 2 seconds

(Reply Delay) before scanning resumes.

UH039P

To initiate scanning,

1. Assuming the unit is on CH01

when switched on.

2. Press and hold channel/scan

or for 3 seconds and

scanning starts and icon is

displayed.

3. Press or to cancel.

Scan

PTT

If channel/scan or is pressed while the

unit is paused on a channel, scanning is resumed.

SCAN

volume

channel/

scan

dup mon

hi/lo

REPLY DELAY

While scanning, the stops at a busy channel and

receives a transmission. When the received signal is over, the

unit will wait for 2 seconds for the return of the signal,

otherwise, the radio resumes scanning.

The flashes during the Setting mode. Press channel/scan

or to select or is shown on the display

when Keylock on is selected to on.

VOX

KEYLOCK ON/OFF

VOX

'oF'

VOX

is the automatic transmitting function by inputting voice

into the optional headset mic without pressing the

button.

Press two times momentarily in Stand By mode to enter

Sensitivity mode.

The current selected setting will flash on the

display.

Press channel/scan or to adjust the sensitivity. 1

is the highest sensitivity and 4 is the lowest sensitivity.

can be turned off by selecting . The icon is shown on

the display when is selected to on.

The icon blinks when the voice level is of a level where it

is possible to transmit at the current selected sensitivity

level.

Press two times momentarily to confirm the selected

setting and exit to standby.

Press three times momentarily in Stand By mode to enter

Keylock mode.

To exit Keylock on mode, press and hold to turn the unit

off and then turn on again.

VOX

'on' 'oF'.

UH039P

CTCSS

channel indicator

Press to confirm the selected setting.

PTT

While in Keylock on mode, the UH039P will still

receive transmissions.

Inhaltsverzeichnis

Andere Uniden Zwei-Wege-Funkgerät Handbücher

Uniden

Uniden GMR2238-3CKDC Bedienungsanleitung

Uniden

Uniden MHS350 - VHF Benutzerhandbuch

Uniden

Uniden Atlantis 290 Bedienungsanleitung

Uniden

Uniden ecoterra GMR648-2CK Bedienungsanleitung

Uniden

Uniden ecoterra GMR645-2CK Bedienungsanleitung

Uniden

Uniden UH060SX-2 Bedienungsanleitung

Uniden

Uniden UM525 Bedienungsanleitung

Uniden

Uniden GMR1048-2CK Bedienungsanleitung

Uniden

Uniden GMR4040-2CKHS Bedienungsanleitung

Uniden

Uniden GMRS380 Bedienungsanleitung

Uniden

Uniden MHS75 Bedienungsanleitung

Uniden

Uniden ATLANTIS250 BK - ATLANTIS 250 VHF Radio Benutzerhandbuch

Uniden

Uniden GMR3040-3CK Bedienungsanleitung

Uniden

Uniden GMR3799-2CK Bedienungsanleitung

Uniden

Uniden UH038SX-2NB Bedienungsanleitung

Uniden

Uniden SX167 series Bedienungsanleitung

Uniden

Uniden GMRS480 Bedienungsanleitung

Uniden

Uniden GMR855-2 Bedienungsanleitung

Uniden

Uniden VOYAGER - VHF Benutzerhandbuch

Uniden

Uniden GMR2238-2CK Bedienungsanleitung

Uniden

Uniden GMRS540 Bedienungsanleitung

Uniden

Uniden GMR635-2 Bedienungsanleitung

Uniden

Uniden GMR1636-2C Bedienungsanleitung

Uniden

Uniden GMR635-2 Bedienungsanleitung

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

Midland

Midland 70-1526A/B Bedienungsanleitung

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Midland

Midland MXT275J Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung