Unit UTD4000 Series Bedienungsanleitung
Uni-Trend Technology (Chengdu) Ltd
Page1of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
UNI-T
Operating Manual and Installation Instructions
Document No. SYSC-
February 2009
Oscilloscope Communication & Control Software
Operating Manual
Page2of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Copyright Information
1. Uni-Trend Technology (Chengdu) Ltd. All rights reserved.
2. Products of the Company are protected by patents granted and pending in the
People’s Republic of China.
3. Information contained in this manual supercedes all information in previously
published versions.
4. The Company reserves the right to change specifications and prices.
Note : Uni-T is the registered trademark of Uni-Trend Technology (Dongguan) Ltd.
Uni-Trend Technology (Chengdu) Ltd
Page3of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Table of Contents
Chapter 1 Installation of the oscilloscope communication
and control software …………………………………
4
1.1 Hardware requirements ………………………………………….. 4
1.2 Installing the software …………………………………………… 4
1.3 Running the software ……………………………………………. 8
1.4 Installing the USB driver ………………………………………… 9
Chapter 2 Getting to know your oscilloscope communication
and control software …………………………………
12
2.1 The control panel …………………………..……………………... 12
2.2 Main menu ……………………………………………..…………. 13
2.3 Control panel instructions ………………………………...………. 18
2.4 Far Control and explanatory notes ………………...….. 20
Chapter 3 Operation
g
uide for the oscilloscope communication
and control software …………………………………
21
3.1 USB interface controls ……………………………………………. 21
3.2
3.3
Ethernet (LAN) interface controls ………………………………...
GPIB interface controls …………………………………………...
23
24
Chapter 4 System Prompts and Trouble-shooting …………….. 25
4.1 System prompts …………………………………………………... 25
4.2 Troubleshooting ……………………..……………………………. 25
Uni-Trend Technology (Chengdu) Ltd
Page4of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Chapter 1 Installation of the oscilloscope communication and
control software
1.1 Hardware requirements
Equipment requirements Minimal.
Oscilloscope UTD4000 Digital Storage Oscilloscope.
Computer Windows 2000/XP/Vista, 128 MB RAM, 16x CD-ROM or better (Vista
users please refer to its individual hardware requirements), SVGA display
or better.
Connection cable USB A-B connection cable
1.2 Installing the software
Your UTD4000 Series Digital Storage Oscilloscope (“Oscilloscope”) comes with an oscilloscope
communication and control software (contained in the CD-Rom supplied with your oscilloscope)
File name : UTD4000 Digital storage oscilloscope communication control software Operating
Manual and Installation Guide.
Installation :
Step one : Insert the CD-ROM supplied with your oscilloscope into the CD-Rom drive of the
computer. Wait for the system to read and find the oscilloscope communication and control software
contents (Fig. 1-1).
Fig1-1
Note : 1.The installation pack downloaded online must be unzipped before application.
2.The software supports Windows 2000, Windows XP and Vista operating systems. On
Vista only USB2.0 communication protocol is supported.
Step two : Double left click the mouse to run the oscilloscope communication and control
software installation as shown in Fig 1-1.
The installation wizard for the oscilloscope communication and control software will
pop up, as shown in Fig. 1-2.
Uni-Trend Technology (Chengdu) Ltd
Page5of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Fig 1-2
Step three : Read the prompt in Fig 1-2 then click the [NEXT (N)] button to enter the next step, as
shown in Fig 1-3.
Fig 1-3
Step four : In Fig 1-3, enter your user name and company name, then click the [NEXT (N)] button
to enter the next step, as shown in Fig 1-4.
Uni-Trend Technology (Chengdu) Ltd
Page6of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Fig 1-4
Step five : In Fig 1-4, click the [CHANGE (H) …] button to specify the installation path of the
software, then click [NEXT (N)]. You can also click [NEXT (N)] directly to use the
default path. Enter the screen shown in Fig 1-5.
Fig 1-5
Step six : In Fig 1-5, after confirming the message is correct, click [NEXT (N)] to enter the front
page for automatic installation, as shown in Fig 1-6.
Uni-Trend Technology (Chengdu) Ltd
Page7of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
Fig 1-6
Step seven : When automatic installation is complete and the box shown in Fig 1-7 pops up, click
the [FINISH (F)] button. Your oscilloscope communication and control software is
now successfully installed on your computer and ready for use.
Fig 1-7
To return to the previous installation guide interface, click [BACK (B)] on any installation guide
page.
To stop installation, press [CANCEL (C)] on any installation guide page.
Uni-Trend Technology (Chengdu) Ltd
Page8of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
1.3 Running the software
When installation of the oscilloscope communication and control software is complete, you can run it on
your computer in two ways.
1. When installation of the oscilloscope communication and control software is complete, an short-cut
icon is automatically created on the computer desktop, as shown in Fig 1-8. To run the software,
simply double left click the icon in Fig 1-8 with your mouse.
Fig 1-8
2. Alternatively, you can run the software by going through START →Programme →Digital storage
oscilloscope →DSO, as shown in Fig 1-9.
Fig 1-9
Uni-Trend Technology (Chengdu) Ltd
Page9of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
1.4 Installing the USB driver
If you are using the oscilloscope’s USB device port for software communication and control, the USB
driver must be installed after installation of the oscilloscope communication and control software is
complete. Follow the steps below :
1. There is a USB device port on the rear panel of your UTD4000 Series Digital Storage Oscilloscope.
With the supplied USB A-B cable, you can connect the USB device port to the USB Host port of the
computer and obtain power supply for the oscilloscope.
2. After checking that connection and power supply are normal, power on the digital storage
oscilloscope. When the operation status screen appears, a prompt will appear at the right bottom
corner to indicate “New hardware DSO detected”, as shown in Fig 1-10.
Fig 1-10
Next, an icon will be created for the “New hardware DSO detected”, as shown in Fig 1-11.
Fig 1-11
Then a “hardware update wizard” dialog box will pop up on the desktop, as shown in Fig 1-12.
Fig 1-12
Uni-Trend Technology (Chengdu) Ltd
Page10of27
UTD4000 Digital storage oscilloscope communication control software Operating Manual and Installation Guide
3. In the new hardware wizard dialog box in Fig 1-12, select the “automatic software installation
(recommended) (I) option, then click [NEXT (N)] to enter the automatic driver search and
installation page, as shown in Fig 1-13.
Fig 1-13
4. As shown in Fig 1-13, the hardware installation wizard of your digital storage oscilloscope begins
automatic searching and installing the USB driver for the oscilloscope communication and control
software. When installation is complete the dialog box shown in Fig 1-14 pops up.
Fig 1-14
Uni-Trend Technology (Chengdu) Ltd
Andere Handbücher für UTD4000 Series
1
Inhaltsverzeichnis
Andere Unit Messgerät Handbücher
Unit
Unit UT310 Series Bedienungsanleitung
Unit
Unit UTS1000 Series Bedienungsanleitung
Unit
Unit UT241 Bedienungsanleitung
Unit
Unit UTE9800+ Series Bedienungsanleitung
Unit
Unit UT381 Bedienungsanleitung
Unit
Unit MIE0149 Bedienungsanleitung
Unit
Unit UT181A Bedienungsanleitung
Unit
Unit UTE9811+ Bedienungsanleitung
Unit
Unit UTS1000 Series Bedienungsanleitung
Unit
Unit UT219P Bedienungsanleitung
Unit
Unit UTE9806+ Bedienungsanleitung
Unit
Unit UT201+ Bedienungsanleitung
Unit
Unit UT255A Bedienungsanleitung
Unit
Unit UTS1000B Series Bedienungsanleitung
Unit
Unit LM50G Bedienungsanleitung
Unit
Unit UT203+ Bedienungsanleitung
Unit
Unit UT372 Bedienungsanleitung
Unit
Unit UT330+ Series Bedienungsanleitung
Unit
Unit UT620C Bedienungsanleitung
Unit
Unit UTS1000B Series Bedienungsanleitung
