Unitech MS100 Bedienungsanleitung

MS100 Bar Code

Pen Reader

AdventureJan

Improper handling, storage, environmental influences and /or

product modification can lead to problems during use.

This is particularly true if repairs and maintenance work are

not performed by trained personnel.

We reserve the right to make technical modifications in accor-

dance with technological advancements as they occur.

General Advisory

FCC Information

This device has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the device is

operated in a commercial environment. This device gener-

ates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference, in which case the user will be

required to correct the interference at his or her own expense.

MS100 Manual

TABLE OF CONTENTS

RS232 31. . . . . . . . . . . . . . . . . . . .

Scanner Port 33. . . . . . . . . . . . . . . . . .

Bar Code Symbologies 35. . . . . . . . . . . . . .

Data Editing 40. . . . . . . . . . . . . . . . . .

Function Codes 45. . . . . . . . . . . . . . . . . .

ASCII Chart 46. . . . . . . . . . . . . . . . . .

SPECIFICATIONS 48. . . . . . . . . . . . . . . . .

TROUBLESHOOTING . . . . . . . . . . . . . . . . 50

WARRANTY 53. . . . . . . . . . . . . . . . . . .

BAR CODE TEST CHART 54. . . . . . . . . . . . . .

Keyboard Wedge 30. . . . . . . . . . . . . . . .

SCANNER CONFIGURATION MANAGER 3. . . . . . . .

Device 6. . . . . . . . . . . . . . . . . . . .

Beeps and Delays 6. . . . . . . . . . . . . . . .

Keyboard Wedge 7. . . . . . . . . . . . . . . .

Scanner Port 11. . . . . . . . . . . . . . . . . .

RS232 9. . . . . . . . . . . . . . . . . . . .

Bar Code Symbologies 14. . . . . . . . . . . . . .

Data Editing 22. . . . . . . . . . . . . . . . . .

PROGRAMMING VIA SCANNER INPUT 25. . . . . . . . .

Quick Setup Bar Codes 26. . . . . . . . . . . . . .

Beeps and Delays 29. . . . . . . . . . . . . . . .

Device Selection and Default 28. . . . . . . . . . . .

INTRODUCTION . . . . . . . . . . . . . . . . . . 1

MS100 Manual

MS100 Manual 1

INTRODUCTION

The MS100 is a family of pen style bar code readers specifically designed

to be a simple, unobtrusive method of scanning bar codes. The operation

is intuitive - simply swipe the MS100 across the bar code you want to read.

The MS100 comes in four interfaces: PS/2, RS232, USB, and TTL Wand,

described below.

Please note that pen bar code scanners might not recognize a given bar

code on the first swipe. All scanners may take several scans to recognize

a particular bar code, but whereas gun type bar code scanners can make

30 scans per second, making even repeated scans seem instantaneous,

pen scanners can only make one scan per swipe.

MS100

MS100A

The Undecoded (or TTL, or Wand) MS100A requires an external decoder

in order to communicate with your computer. Decoders are built into

Wedge devices and many POS (Point of Sale) keyboards, such as the

Unitech KP3700.

The MS100A cannot be configured via Scanner Configuration Manager.

Any modification of the output data must be done in the external decoder.

Normal Operation

MS100-2

The RS232 (Com Port) interface should only be used when your software

is designed to accept com port input. The MS100-2 has a built-in decoder

and outputs the scanned data in ASCII Code. MS100-2 input requires

special software such as HyperTerminal (Bits per second: 9600, Data bits: 8,

Parity: None, Stop bits: 1, Flow control: None) in order to view the output.

The MS100-2 will require an optional power supply unless your computer’s

com port supplies power (unlikely).

MS100 Manual2

MS100-3

The MS100-3 AT keyboard wedge interface has a “Y” interface cable with

an AT male plug on one end and an AT female plug on the other. The

cable end with the male plug is inserted into your computer’s keyboard

port and your keyboard is plugged into the female plug.

The MS100-3 operation should be “plug and play”. The MS100-3 has a

built-in decoder that outputs the scanned data in Scancode keyboard

format. Your computer will treat your MS100-3’s input as it would normal

keyboard input.

Note: If you are using a laptop computer or a USB keyboard (ie. you are

not using an AT keyboard), then your MS100-3 will need to be configured

as a “Keyboardless Wedge” (see “Device” in the “Scanner Configuration

Manager” section.

MS100-3PS2

The PS/2 Keyboard Wedge interface is the most popular and straightfor-

ward. The MS100-3PS2 has a “Y” interface cable with a PS/2 male plug

on one end and a PS/2 female plug on the other. The cable end with the

male plug is inserted into your computer’s keyboard port (not the mouse

port!) and your keyboard is plugged into the female plug.

The MS100-3PS2 operation should be “plug and play”. The MS100-3PS2

has a built-in decoder that outputs the scanned data in Scancode key-

board format. Your computer will treat your MS100-3PS2’s input as it

would normal keyboard input.

Note: If you are using a laptop computer or a USB keyboard (ie. you are

not using a PS/2 keyboard), then your MS100-3PS2 will need to be

configured as a “Keyboardless Wedge” (see “Device” in the “Scanner

Configuration Manager” section.

MS100-4

The USB interface is becoming popular and relatively foolproof. Your

MS100-4 uses the standard USB driver that has been included in the

Windows Operating System since Windows 98 SE.

The MS100-4 operation should be “plug and play”. The MS100-4 has a

built-in decoder that outputs the scanned data in HID keyboard format.

Your computer will treat your MS100-4’s input as it would normal keyboard

input.

Note: Mac OS10 users might need to update their USB driver.

MS100 Manual

The above icons, from left to right, represent download settings

(from computer to scanner), and upload settings (from scanner to

computer). The third icon opens a Test Pad where you can view the

actual scanner output.

Scanner Configuration Manager software is the simplest and most

foolproof way to configure your scanner settings.

SCANNER CONFIGURATION MANAGER

Above, from left to right, are the standard Windows icons for “New

Document”, Open File”, and “Save File”.

Scanner Configuration Manager saves scanner settings in .cfg files,

so you can have access to a variety of different scanner configura-

tions that you’ve set up.

To reset the scanner back to factory default, click on the “New

Document” icon and download the unmanipulated setting to the

scanner (see below).

After loading and starting SCMSetup.exe the icon to the left

will appear on your desktop:

Start it Up

Click on the SCM icon

and the following screen

will appear:

As you can see, you are

presented with a blank

work area and a row of

icons across the top.

Following is an explana-

tion of each of the icons:

MS100 Manual4

The above four icons are used in the “Data Editing” feature of SCM.

From left to right they are the “Add a Formula” icon, the “Remove a

Formula” icon, and the right-hand two are the “Move Formula” icons

that move selected formulas up or down in relation to each other.

For information on data editing, see page 22.

Click this icon to print a series of bar codes that you can scan in

order to configure your scanner to the current SCM settings.

This option is especially useful if downloading to the scanner is not

an option, like when using an interface adaptor or if Windows NT is

your operating system.

If you can produce PDF files via Acrobat, your SCM configuration

can be sent via e-mail to remote locations where they can be

scanned from a printed PDF file (without having to run SCM).

Help is just a click away.

Download to your Scanner

Once you have SCM configured just the way

you want it, click the Download icon (see page

3). The pop-up box to the right should appear:

Select your appropriate interface: USB, RS232,

or PS/2, and then click “OK”.

The green LED on your scanner should blink and you should see the

message “Download completed successfully”. Now your scanner is

ready to use with its new configuration.

If you should get the message “Download to scanner failed”, don’t

dispair. You can still click the “Print” icon (see above) and scan in

the resulting bar codes to configure your scanner.

MS100 Manual

The screen to the left

appears. Click on any of

the selections under

“Current Settings” to view

its “Attributes”.

Click the upload icon (see page 3) and the following pop-up screen

will appear: (alternatively, you can click on the “New Document”

icon, page 3, in which case the second screen will appear)

First Look

Enter the scanner product

number (MS100, for

example).

Make sure the proper

Interface radio button

is selected, and click "OK".

After selecting your config-

uration settings, click on

the Download icon (see

page 3). The LED on the

top of the scanner will

flash during the download

process. Afterwards, you

will be prompted to do an optional “Quick Test”.

Double-click on any of

the “Attributes” to edit

that attribute. This is

done via a drop-down

menu.

6MS100 Manual

Beep Tone

Select a value from “None” to “High” to set the loudness of the tone,

or select “Low to High” or “High to Low” to set the characteristic of

the tone.

Default is “Medium”.

Intercharacter Delay

Intercharacter Delay is the time duration between data characters

sent from the scanner to the computer. Intercharacter delay is

usually inserted when the data flow must be slowed down for the

benefit of a slower computer.

Default is “1 ms”.

Interblock Delay

Interblock delay is the time duration that can be inserted between

one block of data and another. This function is analogous to the

time duration required between dialing a phone number’s country

code and the phone number itself. The interblock delay can be

inserted via SCM’s Data Editing function (see page 22).

Default is “10 ms”.

Following is a detailed discussion of each of the settings, their

attributes, and the effects each of these will have on data output

from your Unitech scanner.

Settings

The only attribute for the “Device” setting is “Device ID”, which

defines the device to which the scanner is connected (usually a

computer or terminal). Select the setting that most closely de-

scribes your device.

The default selection is “01 - IBM PC/AT, PS/2 MOD 40, 60, 80,

USB”, which is appropriate for most PCs.

Device

The three attributes for “Beeps and Delays” are: “Beep Tone”,

“Intercharacter Delay”, and “Interblock Delay”.

Beeps and Delays

Andere Handbücher für MS100

Inhaltsverzeichnis

Andere Unitech Barcode-Lesegerät Handbücher

Unitech

Unitech ES910 Bedienungsanleitung

Unitech

Unitech MS912 Bedienungsanleitung

Unitech

Unitech MS912+ Bedienungsanleitung

Unitech

Unitech MS210 Bedienungsanleitung

Unitech

Unitech MS84XG Bedienungsanleitung

Unitech

Unitech ES700 Bedienungsanleitung

Unitech

Unitech MS926P Bedienungsanleitung

Unitech

Unitech MS838B Bedienungsanleitung

Unitech

Unitech MS852B Plus Bedienungsanleitung

Unitech

Unitech MS840P Bedienungsanleitung

Unitech

Unitech MS280 Bedienungsanleitung

Unitech

Unitech MS146 Bedienungsanleitung

Unitech

Unitech MS842 Bedienungsanleitung

Unitech

Unitech MS860 Bluetooth Bedienungsanleitung

Unitech

Unitech MS926P Bedienungsanleitung

Unitech

Unitech MS840B Bedienungsanleitung

Unitech

Unitech MS842RB Bedienungsanleitung

Unitech

Unitech MS146 Bedienungsanleitung

Unitech

Unitech MS838 Bedienungsanleitung

Unitech

Unitech MS842RP Bedienungsanleitung

Unitech

Unitech HT660 Wireless edition Installations- und Betriebshandbuch

Unitech

Unitech MS838B Bedienungsanleitung

Unitech

Unitech MS338 Bedienungsanleitung

Unitech

Unitech MS282 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung