Unitech MS916 Bedienungsanleitung

unitech is a registered trademark of unitech Electronics Co., Ltd.

Wireless(BT) Pocket Laser Scanner

- MS916 -

User's Manual

Version 1.0

unitech is a registered trademark of unitech Electronics Co., Ltd.

Preface

About This Manual

Thank you for purchasing the unitech product.

This manual explains how to install, operate and maintain our product.

No part of this publication may be reproduced or used in any form, or by any

electrical or mechanical means, such as photocopying, recording, or

information storage and retrieval systems, without permission in writing from

the manufacturer. The material in this manual is subject to change without

notice.

Regulatory Compliance Statements

FCC Warning Statement

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference with radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. This Transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

2. This device complies with FCC RF radiation exposure limits set forth for

an uncontrolled environment. To maintain compliance with FCC RF

exposure requirements, avoid direct contact to the transmitting antenna

during transmitting.

3. Any changes or modifications (including the antennas) made to this device

that are not expressly approved by the manufacturer may void the user’s

authority to operate the equipment.

Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use

only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the

potential for harmful interference to co-channel Mobile Satellite Systems.

Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and

5.725–5.850 GHz band when associated with an access point (AP).

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

RF Radiation Exposure Statement

For body contact during operation, this device has been tested and meets FCC

RF exposure guidelines when used with an accessory that contains no metal

and that positions the handset a minimum of 1.5 cm from the body.

Use of other accessories may not ensure compliance with FCC RF exposure

guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement

sur le material broilleur du Canada.

unitech is a registered trademark of unitech Electronics Co., Ltd.

European Conformity Statement

unitech Electronics co., Ltd herewith declares that the unitech product is in

compliance with the essential requirements and all other provisions of the

R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low

Voltage 2006/95/EC directive.

The declaration of conformity is available for download at :

https://portal.unitech.eu/public/Safetyregulatorystatement

RoHS Statement

This device conforms to RoHS (Reduction Of

Hazardous Substances) European Union regulations

that set maximum concentration limits on hazardous

materials used in electrical and electronic

equipment.

Waste electrical and electronic equipment (WEEE)

unitech has set up a policy and process to meet the EU

directive 2002/96/EC and update 2003/108/EC

concerning electronic waste disposal.

For more detailed information of the electronic waste

disposal of the products you have purchased from

unitech directly or via unitech’s resellers, you shall either

contact your local supplier or visit us at :

https://portal.unitech.eu/public/WEEE

unitech is a registered trademark of unitech Electronics Co., Ltd.

Taiwan NCC Warning Statement

交通部電信總局低功率電波輻射性電機管理辦法

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者

均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。

unitech is a registered trademark of unitech Electronics Co., Ltd.

Laser Information

The unitech product is certified in the U.S. to conform to the requirements of

DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.

Class II and Class 2 products are not considered to be hazardous. The unitech

product contains internally a Visible Laser Diode (VLD) whose emissions do

not exceed the maximum limits as set forth in the above regulations. The

scanner is designed so that there is no human access to harmful laser light

during normal operation, user maintenance or prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the unitech

product’s optional laser scanner module is located on the memory

compartment cover, on the back of the unit.

* Laser information only applies to the products with laser components.

CAUTION! Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser

light. Use of optical instruments with the scanner, including

binoculars, microscopes, and magnifying glasses, with will

increase eye damage.This does not include eyeglasses worn by

the user.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Battery Notice

1. To guarantee optimal performance, it is advised that rechargeable

batteries be replaced every year, or when 500 charge/discharge cycles

are achieved. It is normal that the battery balloons or expands beyond one

year or the maximum of 500 cycles. Although it does not cause harm, it

cannot be used again and must be disposed of according to the location's

safe battery disposal procedures.

2. If the performance decrease is greater than 20% in a battery, the battery is

at the end of its life cycle. Do not continue to use, and ensure the battery is

disposed of properly.

3. The length of time that a battery lasts depends on the battery type and

how the device is used. Conserve the battery life by doing the following:

Avoid frequent full discharges because this places additional strain on

the battery. Several partial discharges with frequent recharges are

better than a full discharge. Recharging a partially charged battery

does not cause harm because there is no memory.

Keep the battery cool. Avoid a hot car. For prolonged

storage, keep the battery at a 40% charge level.

Do not leave the battery discharged and unused for an extended

period because the battery will wear out and the longevity of the

battery will be at least half of the one with frequent recharges.

4. To keep your battery life time and performance as good, as long as

possible, please do not over charge or over discharge the battery.

5. Please do not leave battery unused for long time without being recharged.

In spite of safety design in the battery pack from unitech, if you may

observe the battery pack being deformed, you should stop using it

immediately. In case of the temperature has met the safety design of

battery pack, the battery will not be recharged anymore. Please check if

you are using a proper power adapter to recharge the battery or contact

your service provider for service.

6. If you cannot recharge the battery after it has been idle for long time and

you may observe the temperature of the battery is increased abnormally,

please do not attempt to recharge it anymore. You shall stop using it as it

may be over-discharged and not functional anymore.

unitech is a registered trademark of unitech Electronics Co., Ltd.

7. Please only use the original battery from unitech. Using third party battery

can damage our products. When such damage is happened, it is not

covered by your warranty.

RISK OF EXPLOSION IF BATTERY IS REPLACED

BYAN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO

THE INSTRUCTION.

如果更換不正確之電池行事會有爆炸的風險

請依製造商說明書處理用過之電池

CAUTION!

如果更换不正确之电池行事会有爆炸的风险

请依制造商说明书处理用过之电池

Battery charge notice

It is important to consider the environment temperature when the battery pack

is charged. Charging is most efficient at normal room temperature or in a

slightly cooler environment. It is essential that batteries are charged within the

stated range of 0°C to 40°C. Charging batteries outside of the specified range

could damage the batteries and shorten their charging life cycle.

CAUTION! Do not charge batteries at a temperature lower than 0°C. This will

increase the internal resistance to cause heat and make the

batteries unstable and unsafe. Please use a battery temperature

detecting device for a charger to ensure a safe charging

temperature range.

Storage and safety notice

Although charged batteries may be left unused for several months, their

capacity may be depleted due to build up of internal resistance. If this happens,

they will require recharging prior to use. Batteries may be stored at

temperatures between -20°C to 60°C, however they may deplete more rapidly

at higher temperatures. It is recommended to store batteries at room

temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to

the specification of each product.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not

connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter which comes with your unitech product is not

meant to be used outdoors or without proper protection from prevent the

power adapter being dropped by water, raining or very humid environment.

It may cause damage to the power adapter and/or the product.

4. Please only use the bundled power adapter or same specification of

adapter to recharge your unitech product. Using a wrong power adapter

can possibly damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of

each product.

Hearing Damage Warning

unitech is a registered trademark of unitech Electronics Co., Ltd.

Worldwide Support

unitech’s professional support team is available to quickly answer questions or

assist with technical-related issues. Should an equipment problem occur,

please contact the nearest unitech regional service representative.

For complete contact information please visit the Web sites listed below:

Taipei, Taiwan – Headquarters Europe

Tel: +886-2-89121122 Tel: +31-13-4609292

E-mail: [email protected] E-mail: [email protected]

Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian

District, New Taipei City 231, Taiwan (R.O.C.)

Website: http://www.ute.com

Address:

Website:

Kapitein Hatterasstraat 19, 5015 BB,

Tilburg, the Netherlands

http://eu.ute.com

China Japan

Tel: +86-59-2310-9966 Tel: +81-3-35232766

E-mail: [email protected] E-mail: [email protected]

Address:

Website:

Room401C, 4F, RIHUA International Mansion,

Xinfeng 3nd Road, Huoju Hi-tech District,

Xiamen, Fujan , China

http://cn.ute.com

Address:

Website:

Kayabacho Nagaoka Building 8F.,1-5-19

Shinkawa, Chuo-Ku,

Tokyo, 104-0033, Japan

http://jp.ute.com

Asia & Pacific / Middle East Latin America

Tel: +886-2-27911556 Tel: +52-55-5171-0528

E-mail: [email protected]e.com

[email protected]

info@mideast.ute.com

E-mail:

Address:

[email protected]

17171 Park Row, Suite 210

Houston, TX 77084USA (Rep.)

Address: 4F., No. 236, ShinHu 2nd Rd.,

NeiHu Chiu, 114, Taipei,Taiwan Website: http://latin.ute.com

Website: http://apac.ute.com / http://mideast.ute.com

North America

Tel: +1-714-8916400

E-mail:

Address:

Website:

[email protected] / [email protected]

6182 Katella Ave, Cypress, CA 90630, USA

http://us.ute.com / http://can.ute.com

Andere Handbücher für MS916

Inhaltsverzeichnis

Andere Unitech Barcode-Lesegerät Handbücher

Unitech

Unitech MS912+ Bedienungsanleitung

Unitech

Unitech MS860G Bedienungsanleitung

Unitech

Unitech MS916 Bedienungsanleitung

Unitech

Unitech HT660 Wireless edition Betriebsanleitung

Unitech

Unitech MS852B Bedienungsanleitung

Unitech

Unitech MS840P Bedienungsanleitung

Unitech

Unitech MS912BT Bedienungsanleitung

Unitech

Unitech MS912+ Bedienungsanleitung

Unitech

Unitech MS351 Bedienungsanleitung

Unitech

Unitech MS852N Bedienungsanleitung

Unitech

Unitech HT630 Bedienungsanleitung

Unitech

Unitech MS860 Bluetooth Bedienungsanleitung

Unitech

Unitech MS842 Bedienungsanleitung

Unitech

Unitech MS852Plus Auto Switching Bedienungsanleitung

Unitech

Unitech MS250 Bedienungsanleitung

Unitech

Unitech MS910 Bedienungsanleitung

Unitech

Unitech MS100 Bedienungsanleitung

Unitech

Unitech MS840P Bedienungsanleitung

Unitech

Unitech MS852LR Bedienungsanleitung

Unitech

Unitech MS652 Bedienungsanleitung

Unitech

Unitech MS852Plus Auto Switching Bedienungsanleitung

Unitech

Unitech MS84X-2 Bedienungsanleitung

Unitech

Unitech AS10 Bedienungsanleitung

Unitech

Unitech MS652 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung