Unitech PT-500 Bedienungsanleitung
0
USER’S GUIDE
PORTABLE DATA COLLECTION
TERMINAL
PT-500
DOCUMENT NUMBER: 350500-0010
1
NOTICE
The unit is equipped with a NiMH
battery pack. It is possible that the
customer might receive the battery pack
in a discharged (dead) state due to
product storage. This is normal.
In the above situation, plug the
9V/500mA AC-DC adapter into the PT500
and an available 110V electrical outlet,
switch on the PT500, and fully charge the
NiMH battery pack for 14-16 hours. Or
place the PT500 into the optional charging
cradle for 3 hours before using the unit.
During the initial charging, switching
on the PT500 is highly recommended. In
addition to charging the main NiMH
battery pack, this will also simultaneously
charge up the backup lithium battery.
2
Table of Content Page
Chapter 1 Overview…...………………………… 1
1.1 Technical Specification……………… 2
1.2 Software System…………………….. 2
1.3 Application Development……………. 2
Chapter 2 Installation
2.1 Power On and Off the PT-500……… 3
2.2 Batteries………………………………. 3
Main Battery………………………….. 3
Backup Battery………………………. 4
2.3 Using the Keypad…………………… 5
2.4 Triggering the Scanner Module……. 6
2.5 Interface Port………………………… 6
2.6 Optional Charging Cradle………….. 8
Chapter 3 Operation………………………..…… 11
3.1 Ready Mode…………………………. 12
3.2 System Mode………………………… 14
1. Run Menu…………………………. 14
2. Set Menu………………………….. 15
3. Dir Menu…………………………… 20
4. Del Menu………………………….. 20
5. Diag Menu………………………… 21
6. Init Menu…………………………... 22
3.3 Easy Job Mode………………………. 23
3.4 Application Mode…………………….. 28
3
Chapter 1 Overview
The PT-500 Portable Data Terminal with built-in barcode
scanner is a rugged, compact and lightweight hand-held
terminal designed for data collection. It offers many features
for efficient barcode reading, keyboard data entry, and data
processing. It is ideal for a wide range of Automatic Data
Collection situations such as transportation, warehouse
distribution, retail management, asset tracking, and many
other applications.
1A2
B 3C
6F
5E
4D
0K
.
L
9I
=J
8H
7G
+M
F3YF4Z
#U
Ins
R
,
?
Del
Q
F2X
$T
?
?
F1
W
%S
/P
*O
-N
Exit Menu
Enter
(YES)
Bksp
SP
(NO)
Caps
EditV
Unitech
Alpha
PT- 500 V1.0
1024KB Total
996KB Free
>
CAUTION
LaserLight-Do
NotStareIntoBeam
670nmLaserDiode
1.0MilliwattMaxOutput
ClassIILaserProduct
MadeinTaiwan
S/N:500PES0001
Front Side Back
Bottom
4
1.1 Technical Specification
?? 8-bit microprocessor CPU.
?? 64KB ROM.
?? 256KB, 512KB, or 1024KB RAM memory.
?? 32x122 dots graphic LCD, 4 lines x 20 characters.
?? Low power consumption.
Standby 25mA
Active 160mA
?? Rechargeable NiMH or 3 disposable AA size
alkaline batteries.
?? Rechargeable Lithium backup battery.
?? Real time clock.
?? 36 keys alphanumeric rubber keypad.
?? Optional integrated laser/CCD scanner.
?? One good read LED indicator to scanner input.
?? One standard RS-232 port.
?? One infrared port communicates to optional cradle.
?? Optional Cradle for Battery charging and Data
Communication via Local Connection or Modem.
Software System
?? Menu driven user interface
?? Built-in Data Collection Application. (EzJob)
?? Built-in System Management and Data Exchange
Program.
?? Build in diagnostic program
?? Barcode Symbologies:
UPC, EAN, CODE39, I 2 OF 5, CODBAR,
MSI, CODE128 and CODE93.
1.3 Application Development
?? Replaceable EPROM.
?? Application Development Tools Kit for C
programming.
5
Chapter 2 Installation
2.1 Power On and Off the PT-500
Press the Power Key ?located near the bottom left corner
to turn the terminal on and off. As a safeguard, the unit can
only be turned off by pressing the power key ?for at least 3
seconds.
2.2 Batteries
Main Battery
The PT-500 operates with either a rechargeable nickel
metal-hydride (NiMH) battery pack or three standard AA size
alkaline batteries. When the main battery is running low, the
LCD display will start blinking. If the unit is switched off and
on again, a warning message stating “MAIN BATTERY
LOW” will appear on the LCD display.
NiMH Battery Pack
Battery Installation Procedure:
1. Turn off the terminal and placeit face down.
2. Move the battery compartment latch to the left to
open. Remove the battery cover.
3. Insert the main batteries:
?NiMH battery:
Place the battery with label facing up; firmly
push the whole pack inside the compartment.
?Alkaline batteries:
6
Insert the batteries in the positions as shown
by the polarity symbols inside compartment
4. Replace the battery cover and move the latch back to
the locked (centered) position.
5. If you are using NiMH battery pack, please charge
the NiMH batteries continuously for 14 to 16 hours
with AC-DC power adapter, or 3 hours with the
optional charging and communication cradle.
Note: The AC-DC power adapter is only for NiMH battery
pack recharging. It won’t recharge alkaline batteries.
Do not incinerate, crush, or puncture batteries.
Do not dispose of alkaline batteries in fire.
Do not attempt to recharge alkaline batteries.
Backup Battery
The PT-500 also has a built-in rechargeable Lithium backup
battery that temporarily protects data stored in RAM. The
power of the Lithium battery is only consumed when the
main power source is not available, such as when the main
battery is removed or discharged. When a functional NiMH
battery pack or 3 AA-size batteries are in the main battery
compartment, power is provided to backup the RAM
memory and system clock, which effectively puts the Lithium
battery in a standby state.
The power circuitry of the PT-500 monitors the voltage level
from the main power source and automatically connects the
Lithium battery for backup once it has detected that
inadequate power is being provided by the main power
source. Under these conditions, the life of theLithium
battery would be up to10 hours. Therefore it is highly
recommended that the main battery always be kept
adequately charged inside the unit.
7
When the PT-500 is switched on and the Lithium battery is
discharged, the following low backup battery warning
message will be displayed on the PT-500 LCD:
In this situation you should upload your data from the PT-
500 to a PC and have the Lithium battery replaced. Contact
your local sales or service representative for replacement of
the Lithium battery.
Note: Data may not be backed up and data loss may occur
if both the main battery and the Lithium battery are
discharged.
2.3 Using the Keypad
The Keypad of the PT-500 consists of 36 rubber keys and
one large scanner trigger button. The keypad layout is
shown in the following picture.
BACKUP BATTERY LOW!
8
1A2
B 3C
6F
5E
4D
0K
.
L
9I
=J
8H
7G
+M
F3
YF4
Z
#U
Ins
R
,
?
Del
Q
F2
X
$T
?
?
F1
W
%S
/P
*O
-N
Exit Menu
Enter
(YES)
Bksp
SP
(NO)
Caps
EditV
Unitech
Alpha
?Turn on and off of the terminal.
Press ?for 3 seconds to turn off terminal.
Alpha Toggle the keypad input between Alpha mode
and Numerical mode. When changed to Alpha
mode, the cursor will change from a “?” to a
“_” prompt on the display.
Menu Go to the System Main Menu and System
Setting.
Exit Exit the current program to the previous
program or menu.
Trigger Activate the integrated scanner module to
scan barcode.
F1~F4 Function keys F1 to F4 can be used under the
normal numerical mode.
Power key to
turn On & Off.
Switch between Alpha
& Numerical keys
Go to system menu
and select setting
Exit key to
previous menu
Integrated scanner
trigger button
Switch to upper &
lower case letter input
9
2.4 Triggering the Scanner Module
The PT-500 can be used with a built-in integrated
laser or CCD scanner module. To use the scanner, just
point the scanner window at a barcode and press the trigger
that activates the scanner. A short beep from the buzzer
and flashing red LED indicator on top of the LCD display
indicates when the scanning is successful.
2.5 Interface Port
The PT-500 includes a DSUB-9 pin male connector, located
at the base of the terminal, for serial communication with a
PC. Infra red LEDs and charging contacts for the optional
cradle are located on the bottom right below the DB 9
connector. The pin out assignment is shown as follows:
15
69
The following diagram shows the way to connect
input/output devices to the PT-500.
Pin
Signal Direction
Description
1
2RXD Input Receive
3TXD Output Transmitted
4
5GND Reference
Ground
6
7RTS Output Ready to send
8CTS Input Clear to send
9
Inhaltsverzeichnis
Andere Unitech Scanner Handbücher
Unitech
Unitech MS336 Bedienungsanleitung
Unitech
Unitech MS852Plus Auto Switching Bedienungsanleitung
Unitech
Unitech MS926 Bedienungsanleitung
Unitech
Unitech MS926 Bedienungsanleitung
Unitech
Unitech MS 230 Bedienungsanleitung
Unitech
Unitech MS380 Bedienungsanleitung
Unitech
Unitech FC75 Bedienungsanleitung
Unitech
Unitech MS337 Bedienungsanleitung
Unitech
Unitech MS140 Bedienungsanleitung
Unitech
Unitech MS910 Bedienungsanleitung
Unitech
Unitech MS916 Bedienungsanleitung
Unitech
Unitech MS916 Bedienungsanleitung
Unitech
Unitech MS912 Bedienungsanleitung
Unitech
Unitech MS912 Bedienungsanleitung
Unitech
Unitech MS912+ Bedienungsanleitung
Unitech
Unitech MS920 Bedienungsanleitung
Unitech
Unitech MS100 Bedienungsanleitung
Unitech
Unitech MS851 Bedienungsanleitung
Unitech
Unitech SL220 Bedienungsanleitung
Unitech
Unitech MS920 Bedienungsanleitung
