Unitronics Samba OPLC SM43-J-R20 Bedienungsanleitung

Unitronics 1

Samba™ OPLC™

SM43-J-R20

Installation Guide

The Unitronics SM43-J-R20 offers the following onboard I/Os:

12 Digital Inputs, configurable via wiring to include:

1 HSC/Shaft-encoder Input, 2 Analog inputs (only when the digital inputs are set to pnp)

8 Relay Outputs

General Description

The SAMBA SM43-J-R20 OPLC is an All-in-One Programmable Logic Controller that

Comprises a built-in 4.3" Color Touchscreen.

Communications

USB device programming port (Mini-B)

Optional: the user may install -

RS232/RS485 port (V100-17-RS4/V100-17-RS4X) or Ethernet (V100-17-ET2)

& CANbus (V100-17-CAN)

Standard

it Contents

Samba controller Mounting brackets (x2)

I/O connectors (x2) Rubber seal

Battery (installed)

Alert Symbols and General Restrictions

When any of the following symbols appear, read the associated information carefully.

Symbol Meaning Description

Danger The identified danger causes physical and property damage.

Warning The identified danger could cause physical and property damage.

Caution Caution Use caution.

Before using this product, the user must read and understand this document.

All examples and diagrams are intended to aid understanding, and do not guarantee operation.

Unitronics accepts no responsibility for actual use of this product based on these examples.

Please dispose of this product according to local and national standards and regulations.

Only qualified service personnel should open this device or carry out repairs.

Failure to comply with appropriate safety guidelines can cause severe injury or property damage.

Do not attempt to use this device with parameters that exceed permissible levels.

To avoid damaging the system, do not connect/disconnect the device when power is on.

Environmental Considerations

Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration, in accordance with

the standards given in the product’s technical specification sheet.

Do not place in water or let water leak onto the unit.

Do not allow debris to fall inside the unit during installation.

Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.

Install at maximum distance from high-voltage cables and power equipment.

SM43-J-R20 Installation Guide

2 Unitronics

Mou

nting

Dimensions

Panel Mounting

Before you begin, note that the mounting panel cannot be more than 5 mm thick.

1. Make a panel cut-out

measuring 122.5x91.5 mm

(4.82”x3.6”).

2.Slide the controller into the cut-

out, ensuring that the rubber

seal is in place.

3.Push the mounting brackets into

their slots on the sides of the

panel as shown in the figure to

the right.

4.Tighten the bracket’s screws

against the panel. Hold the

bracket securely against the unit

while tightening the screw.

5.When properly mounted, the

controller is squarely situated in

the panel cut-out as shown in

the figure to the right.

Samba™ OPLC™

Unitronics 3

Wiring

Do not touch live wires.

Install an external circuit breaker. Guard against short-circuiting in external wiring.

Use appropriate circuit protection devices.

Unused pins should not be connected. Ignoring this directive may damage the device.

Double-check all wiring before turning on the power supply.

Caution

To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).

Do not use tin, solder, or any substance on stripped wire that might cause the wire

strand to break.

Install at maximum distance from high-voltage cables and power equipment.

Wiring Procedure

Use crimp terminals for wiring; use 3.31 mm ² –0.13 mm² wire (12-16 AWG):

1.Strip the wire to a length of 7±0.5mm (0.270–0.300“).

2.Unscrew the terminal to its widest position before inserting a wire.

3.Insert the wire completely into the terminal to ensure a proper connection.

4.Tighten enough to keep the wire from pulling free.

Input or output cables should not be run through the same multi-core cable or share the same wire.

Allow for voltage drop and noise interference with I/O lines used over an extended distance.

Use wire that is properly sized for the load.

The controller and I/O signals must be connected to the same 0V signal.

I/Os

This model comprises a total of 12 inputs and 8 relays. Input functionality can be adapted as follows:

1.All 12 inputs may be used as digital inputs. They may be wired in a group via a single jumper

as either npn or pnp.

In addition, according to jumper settings and appropriate wiring:

- Inputs 5 and 6 can function as either digital or analog inputs.

•If the digital inputs function as npn, analog option is not available.

- Input 0 can function as a high-speed counter, as part of a shaft-encoder, or as a normal

digital input.

- Input 1 can function as either a counter reset, normal digital input, or as part of a

shaft-encoder.

- If input 0 is set as a high-speed counter (without reset), input 1 can function

as a normal digital input.

SM43-J-R20 Installation Guide

4 Unitronics

Input and Output Jumper Settings

The tables below show how to set a specific jumper to change input functionality. To access the I/O

jumpers, you must open the controller according to the instructions beginning on page 7.

Incompatible jumper settings and wiring connections may seriously damage the controller.

Digital Inputs 0-11: Set Type

Set to JP12 (all Inputs)

npn (sink) A

pnp (source)* B

Input 5: Set Type - Digital or Analog #1

Set to JP4 JP10

Digital* A A

Voltage B A

Current B B

Input 6: Set Type - Digital or Analog #0

Set to JP8 JP9

Digital* A A

Voltage B A

Current B B

*Default settings

I/O Wiring

] npn Input Wiring

Input wiring, npn (sink) HSC input wiring, npn (sink)

pnp Input Wiring

Input wiring, pnp (source) HSC input wiring, pnp (source)

Samba™ OPLC™

Unitronics 5

Shaft-encoder

Analog Input W

iring

Analog input wiring, current (2/3 wire) Analog input wiring, current/voltage (4-wire)

Shields should be connected at the signal’s source.

The 0V signal of the analog input must be connected to the controller’s 0V.

Relay Outputs

Increasing Contact Life Span

To increase the life span of the

relay output contacts and protect

the device from potential damage

by reverse EMF, connect:

A clamping diode in parallel with each

inductive DC load

An RC snubber circuit in parallel with

each inductive AC load

SM43-J-R20 Installation Guide

6 Unitronics

Power Supply

The controller requires an external 24VDC power supply.

1. The power supply must include double insulation. Outputs must be rated as

SELV/PELV/Class 2/Limited Power.

2. Use separate wires to connect the functional

earth line (pin 3) and the 0V line (pin 2) to the

system earth ground.

3. Install an external circuit breaker. Guard

against short-circuiting in external wiring.

4. Double-check all wiring before turning

on the power supply.

5. Do not connect either the ‘Neutral’ or ‘Line’

signal of the 110/220VAC to device’s 0V pin.

6. In the event of voltage fluctuations or non-

conformity to voltage power supply

specifications, connect the device to

a regulated power supply.

Earthing the OPLC

To maximize system performance, avoid electromagnetic interference by:

Mounting the controller on a metal panel.

Connect each common and ground connection directly to the earth ground of your system.

For ground wiring use the shortest and thickest possible wire.

Communication Port

This series comprises a USB port and a CANbus port

Turn off power before making communications connections.

Caution

Always use the appropriate port adapters.

The USB port is not isolated. Make sure that the PC and the controller are grounded to

same potential.

The USB port may be used for programming, OS download, and PC access.

Samba™ OPLC™

Unitronics 7

Opening the Controller

Before performing these actions, touch a grounded object to discharge any electrostatic charge.

Avoid touching the PCB board directly. Hold the PCB board by its connectors.

1.Turn off the power supply, disconnect, and dismount the controller.

2.The back cover of the controller comprises 4 screws, located in the corners. Remove the

screws, and pull off the back cover.

Changing I/O Settings

1.The I/O board of the controller is now exposed, enabling you to change

I/O settings according to the jumpers shown on page 4.

Closing the Controller

1.Replace the back cover of the controller and fasten the corner screws.

Note that you must replace the back cover securely before powering up the controller.

SM43-J-R20 Installation Guide

8 Unitronics

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole

discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or

temporarily withdraw any of the forgoing from the market.

All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of

merchantability, fitness for a particular purpose, or non infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in

this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising

out of or in connection with the use or performance of this information.

The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other

third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them

DOC17009-A9 09/14

Andere Handbücher für Samba OPLC SM43-J-R20

Inhaltsverzeichnis

Andere Unitronics Controller Handbücher

Unitronics

Unitronics Jazz OPLC JZ20-T40 Bedienungsanleitung

Unitronics

Unitronics US5-B5-RA28 Bedienungsanleitung

Unitronics

Unitronics UniStream USC-B5-R38 Bedienungsanleitung

Unitronics

Unitronics Vision V130-J-TA24 Bedienungsanleitung

Unitronics

Unitronics Jazz JZ20-UA24 Bedienungsanleitung

Unitronics

Unitronics Vision V350-35-TU24 Bedienungsanleitung

Unitronics

Unitronics V120-22-R34 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V560-T25B Bedienungsanleitung

Unitronics

Unitronics Vision 230 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V1040-T20B Bedienungsanleitung

Unitronics

Unitronics US5-B10-RA28 Bedienungsanleitung

Unitronics

Unitronics Jazz JZ20-J-UN20 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V350-35-TA24 Bedienungsanleitung

Unitronics

Unitronics UniStream USC-B10-RA28 Bedienungsanleitung

Unitronics

Unitronics Vision V130-J Series Bedienungsanleitung

Unitronics

Unitronics M90 OPLC Bedienungsanleitung

Unitronics

Unitronics Vision120 Bedienungsanleitung

Unitronics

Unitronics Vision130 Bedienungsanleitung

Unitronics

Unitronics Jazz OPLC JZ20-R10 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V570-57-T34 Bedienungsanleitung

Unitronics

Unitronics Vision V570-57-T40B Bedienungsanleitung

Unitronics

Unitronics UniStream US5-B5-B1 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V130 Bedienungsanleitung

Unitronics

Unitronics Vision OPLC V1040-T20B Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung