Uplift Desk Crestview MON031 Bedienungsanleitung

Crestview Single Monitor Arm

MON031

For assembly assistance,

visit upliftdesk.com/contact,

call 800-349-3839,

or email [email protected]

Scan QR code for

product webpage

Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from

improper use of this product. Please provide these instructions to any new user or owner of the product.

CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result

in damage or personal injury. Retain manual for future reference.

Warning: This product contains a spring mechanism that can cause injury. Be careful when

removing monitors as the arm can spring up when the weight of the monitor is removed.

Safety and Warnings

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Upper Clamp

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Lower Clamp

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Upper Arm

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

Lower Arm

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Upper Base Plate

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Lower Base Plate

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Adhesive Pad

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

VESA Plate

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

Wire Cover

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Allen Wrenches

Set of three: 3mm, 4mm, 6mm M6 x 12 Flathead Screw

qty 4

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

M4 x 12 Scew (M-A)

qty 4

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

M5 x 12 Scew (M-B)

qty 4

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

M5 Washer (M-C)

qty 4

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

Package Contents

Hardware Components

Assembly Instructions

WARNING: This product contains a spring mechanism that can cause injury. Be careful when removing monitors as the arm can

spring up when the weight of the monitor is removed.

Note: There are two ways to attach to your desktop: Clamp and Bolt-through mount. Determine if you need to attach it around the

back side of your desk or through a hole from 0.4’’ to 3.15’’ in diameter.

Acceptable monitor weight range: 2.2 to 33 lb

Desktop thickness compatibility: Clamp Method: 0.4”-3.3” thick | Bolt-through Method: 0.4”-1.8” thick

Step 1 - Clamp

If you purchased the Crestview Monitor Arm Wiring Kit,

assemble that FIRST, before proceeding. Refer to the

separate instructions contained in the Crestview Monitor

Arm Wiring Kit (ACC076) package for complete details.

Step 2

Determine your mounting method. There are two ways to

attach the Crestview Single Monitor Arm to your desktop:

Clamp Method: If you would like attach the monitor arm

along the back edge of your desktop, follow the Clamp

Method instructions (Steps 3 - 5) and ensure your desk is

between 0.4” and 3.3” thick.

Bolt-Through Method: If you prefer to attach the monitor

arm through your desktop, skip steps 3 - 5 and follow

the Bolt-Through Method Instructions (Steps 6 - 9) and

ensure your desk is between 0.4” and 1.8” thick.

Step 3 (Clamp Method)

A. Align the Upper Clamp with the Base in the orientation

shown. Attach using four M6 x 12 Flathead Screws and

the 4mm Allen Wrench.

B. Then peel the adhesive backing off of the Adhesive

Pad and attach it to the bottom of the Base and Upper

Clamp as shown. Align the pad with the front edge of

the Base rst, then work to the back.

Clamp Method Bolt-Through Method

Base

Lower arm

Upper arm

Vesa mount (x1)

Lower base plate

Upper base plate

Bar Handle

Adhesive Pad

Wire Cover

Upper Clamp

Lower Clamp

Base screw (x4)

3mm Allen wrench

4mm Allen wrench

6mm Allen wrench

D5 Washers (x4)

M5x12 bolt (x4)

M4x12 bolt (x4)

O Bolt (x4)

N Bolt (x4)

0.25”

Step 4 (Clamp Method)

A. Use the 4mm Allen Wrench to adjust the four pre-

installed screws on the back of the Lower Clamp so

that there are about 0.25” of thread between the plate

and screw heads.

B. Insert the four screws of the Lower Clamp through four

of the key slot holes in the back of the Upper Clamp as

shown. There are two sets of key slot holes to choose

from for different desktop thicknesses.

• For Desks 0.4” to 2.25” use the top four key slot holes

(g. 1)

• For Desks 2” to 3.3” use the bottom four key slot

holes (g. 2)

C. Slide the Lower Clamp assembly down so that the

screws are at the bottom of the key slot holes then

tighten screws with 4mm Allen Wrench.

g. 2

.25”

g. 1

0.25”

Step 6 (Bolt-Through Method)

Ensure the desktop has a hole between 0.4’’ and 3.1’’ in

diameter to use this option. Using a grommet hole that

is already in your desktop is acceptable, or you can drill a

0.5” hole anywhere on your desktop.

Step 5 (Clamp Method)

A. Using the 6mm Allen Wrench, adjust both bolts on the

bottom of the Lower Clamp so that the opening is wide

enough to accommodate the thickness of the desktop

and Lower Base Plate.

B. Place the outer holes of the Lower Base Plate onto the

tips of the bolts as shown.

C. Slide the assembly onto the back of the desktop,

then tighten the bolts using the 6mm Allen Wrench.

Alternate from one bolt to the other, to allow the Lower

Base Plate to rise evenly before nally tightening to the

desktop.

D. If you chose the Clamp Method for mounting, please

skip the Bolt-Through Method Steps 6-9 and proceed

with Step 10.

Step 7 (Bolt-Through Method)

A. Align the Upper Base Plate with the Base in the

orientation shown and attach it using the four M6 x 12

Flathead Screws and the 4mm Allen Wrench.

B. Then peel the adhesive backing off of the Adhesive Pad

and attach it to the bottom of the Base and Upper Base

Plate as shown. Align the pad with the front edge of the

Base rst, then work to the back.

.4” 3.1”

180°

Step 8 (Bolt-Through Method)

A. Remove one of the bolts from the bottom of the Lower

Clamp using the 6mm Allen Wrench. Slip it through

the Lower Base Plate’s center hole as shown.

B. If assembling on an adjustable height desk, raise the

desk so the desktop hole is easier to see. Then insert

the bolt through the desktop hole from below, and hold

them in place.

Step 9 (Bolt-Through Method)

A. While holding the Lower Base Plate and bolt in place

from below, line up the hole of the Base assembly

(from Step 7) with the top of the bolt.

B. Make sure the front of the Base assembly is facing

towards the front of yoHold the Base assembly in

place on top as you hand tighten the bolt from below

to get the threads started. Once the bolt is started,

you can let go of the Lower Base Plate. Use the 6mm

Allen Wrench to nish tightening the assembly to the

desktop.

C. Proceed with the Arm Assembly, Step 10.

Step 10

A. Slide the Lower Arm onto the post of the Base until it

is fully seated and tighten the lower set screw with the

at-head end of the 3mm Allen Wrench (or a small at

head screwdriver). This will secure the Lower Arm to

the Base and keep it from becoming separated during

adjustment.

B. The Lower Arm can swivel a full 360° or can be set to

allow only a range of 180°.

• To allow 360° of rotation, leave the upper set screw

alone, and the Lower Arm will rotate a full 360°

around past the back of the desk.

• To limit the Lower Arm to only 180° of rotation,

tighten the upper set screw. This setting is helpful

when your desk is located against a wall or you are

installing a privacy panel to the back of the desk. Do

not over-tighten this set screw, doing so may hinder

arm movement.

Step 12

Reminder: Acceptable monitor weight range for the

Crestview Single Monitor Arm is 2.2 lb to 33 lb.

A. Lay your monitor face down on a clean surface or a

towel to prevent damage to your screen.

B. Test the M4 x 12 and M5 x 12 Screws in your monitor’s

screw holes to determine which is the right size for

your monitor.

C. Line up the holes of the VESA Plate with the holes on

your monitor. Make sure the word “TOP” is facing the

top of the monitor.

D. Attach the VESA Plate to the monitor using the

selected screws with the M5 Washers.

Step 13

A. Pull the tab on the Upper Arm back and slide the VESA

Plate in (as shown in the illustration) until the tab on

the Upper Arm clicks into place

B. Pull up slightly on your monitor to make sure it is

locked securely in place.

Step 11

A. Slide the Upper Arm into the hole on the Lower Arm

until it is fully seated

B. Tighten the set screw on the Lower Arm with the

at-head end of the provided 3mm Allen Wrench (or

a small at head screwdriver). This will prevent the

Upper Arm from becoming separated from the Lower

Arm during adjustment.

Step 14

A. Move the monitor to any position and release it. If the

monitor does not drift up or down, the Arm is properly

counterbalanced.

B. If the Arm does not remain where you positioned it,

you will need to adjust the tension of the gas spring to

properly support the weight of your monitor.

• If the monitor drifts down when you let it go, hold

the Arm in a horizontal position as shown and use

the 6mm Allen Wrench to turn the adjustment

screw toward the “+” until the monitor remains in

place when you let go.

• If the monitor drifts upward when you let go, turn

the adjustment screw towards the “-” until the

monitor remains in place when you let go.

Step 15

A. To adjust the front and back tilt of your monitor, loosen

the socket head screw on the side of the VESA Mount

with the 6mm Allen Wrench.

B. Once the monitor is at your preferred viewing angle,

re-tighten the screw with the Allen Wrench to hold the

monitor in place.

Step 16

A. To use the Arm’s wire management, rst remove the

built-in wire covers.

B. The Upper Wire Cover is located on the bottom side of

the Arm and is held in place by a screw at the top end

and a clip at the bottom end. Remove the screw with a

Phillips head screwdriver and slide the cover slightly

toward the Worksurface to disengage the clip and

remove the cover.

C. The Lower Wire Cover is located on the Lower Arm and

is removed by hooking a nger through the bottom

opening in the cover, then holding it rm while pulling

it forward to unlock.

D. Run your cables under the Arms where the wire covers

were located and then replace the covers. Your cables

should run through each end of both the Upper and

Lower Wire Covers.

E. Reinstall the screw to secure the Upper Wire Cover.

Step 17

A. If you have selected the Clamp Method, you can now

snap the Wire Cover onto the back of the Upper Clamp

as shown and insert your monitor cables through the

two integrated clips.

B. The Wire Cover adds 0.8” to the back of the Clamp

assembly. If your desk is close to a wall or cubicle

or has a privacy panel attached to the back of the

desktop, there may not be enough space available to

attach the Wire Cover.

Height Adjustment

The center of the VESA mount can go as high as 23” and

as low as 10’’ from the desktop.

Monitor Tilt

The Monitor can tilt at the VESA mount forward or

backward within a range of 90° (+/-45°).

Monitor Swivel

The Monitor can swivel 180° (+/-90°) at the hinge at the

top of the Upper Arm.

Monitor Rotation

The Monitor can rotate at the VESA mount 180° (+/-90°)

allowing landscape or portrait viewing.

23”

10”

Upper Arm Swivel

The Upper Arm can swivel a full 360°. However, we do not

recommend swiveling the monitor past the back of the

desk as this may cause instability.

Lower Arm Swivel

The Lower Arm can swivel a full 360° or can be set to allow

only a range of 180°.

See Step 10 in the “Arm Assembly & Monitor Mounting”

section for adjustment details.

Notes

Inhaltsverzeichnis

Andere Uplift Desk Rack & Stand Handbücher

Uplift Desk

Uplift Desk MON042 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC095 Bedienungsanleitung

Uplift Desk

Uplift Desk Crestview MON032 Bedienungsanleitung

Uplift Desk

Uplift Desk Motion-X 6-Pack Rack ACC052 Bedienungsanleitung

Uplift Desk

Uplift Desk CPU001 Bedienungsanleitung

Uplift Desk

Uplift Desk Zilker Single Monitor Arm Bedienungsanleitung

Uplift Desk

Uplift Desk STR045 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC092 Bedienungsanleitung

Uplift Desk

Uplift Desk MON041 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC301 Bedienungsanleitung

Uplift Desk

Uplift Desk STR017-SHT Bedienungsanleitung

Uplift Desk

Uplift Desk Zilker MON002 Bedienungsanleitung

Uplift Desk

Uplift Desk MON021 Bedienungsanleitung

Uplift Desk

Uplift Desk Crestview MON033 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC055 Bedienungsanleitung

Uplift Desk

Uplift Desk MON001 Bedienungsanleitung

Uplift Desk

Uplift Desk MON051 Bedienungsanleitung

Uplift Desk

Uplift Desk MON021 Bedienungsanleitung

Uplift Desk

Uplift Desk Zilker Dual Monitor Arm Bedienungsanleitung

Uplift Desk

Uplift Desk Crestview MON033 Bedienungsanleitung

Uplift Desk

Uplift Desk UPL021 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC304 Bedienungsanleitung

Uplift Desk

Uplift Desk ACC303 Bedienungsanleitung

Uplift Desk

Uplift Desk MON041 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung