USA Technologies EPort G9 Bedienungsanleitung

HSPA ePort G9 Quickstart Guide

USA TECHNOLOGIES

TOOLS REQUIRED FOR INSTALLATION

11/32” Socket

1/4” Socket

12” Extension

Ratchet

Phillips Screwdriver

Wire Cutters

Power Drill*

3/16” & 3/8” Drill Bit*

Multi-diameter Step Drill Bit,

1/4”-3/4”*

#VVXUD0101911

* Required for surface-mount installations

Thank you for your purchase. Before you start, please read these instructions thoroughly,

and then take a few moments to plan your installation.

You must have a signed ePort Connect Services Contract and a bank account assigned to

this device for it to be able to accept credit card transactions. Please call USA Technologies

Customer Care at 1.888.561.4748, if you need activation documents.

G9 Telemeter Card Reader

INSTALLATION PROCEDURES FOR THE G9 EPORT

The G9 ePort® works in vending machines with one or two full bill acceptor openings,

allowing the acceptance of credit/debit transactions by using Card Swipe or RF technol-

ogy payments. The G9 ePort solution works with the MDB vending interface. Addition-

ally, the G9 has interfaces for Coin Pulse systems, along with a serial interface for PC

based systems. In both Coin Pulse and Serial Modes, parameters can be modied to

meet design requirements.

KIT CONTENTS

Your HSPA Wireless G9 ePort kit includes (Shown in Figure 1 unless noted):

• One G9 Telemeter with wireless modem installed (#VVWUT0101902)

• One Card Reader (Bezel) (#V8SUK1235003)

• One Flange Mount Plate (#V6XUE1520259)

• One Bezel Drilling Template

• One Bezel Adapter Cable (#V6SUC1435003)

• One Magnetic Base Antenna (#V8WUP0101278)

• Mounting Hardware: Four, 8-32 x 3/8” screws for mounting reader, and three self-

drilling screws (#DCHZDHH62006)

• NOT PICTURED: Various POS stickers, Troubleshooting Checklist (#V8VUD1101435),

RMA Procedure Sheet (#UXXUD0101552), this install guide (#VVXUD0101911), two

Velcro strips, six Wire Ties for the Card Reader, and additional order items

BEFORE YOU START, read the instructions and take a few moments to plan your instal-

lation. Pick a mounting spot for the G9 Telemeter that will allow for ease of access and

does not interfere with any moving parts in your vending equipment.

FIGURE 1 (items not to scale)

G9 Telemeter

#VVWUT0101902 Card Reader (Bezel)

#V8SUK1235003 Flange Mount Plate

#V6XUE1520259 Bezel Drilling

Template

Mounting Hardware #DCHZDHH62006

Four, 8-32 x 3/8” mounting screws, three self-drilling screws.

Bezel Adapter Cable

#V6SUC1435003

Magnetic Base

Antenna

#V8WUP0101278

1. RSSI SIGNAL STRENGTH TESTING PROCEDURE

Parts Required for RSSI Test: G9 Telemeter and a Magnetic Base Antenna

Optional: A Card Reader and a High Gain Antenna (see note) of 4’or 8’ cable length

(#VXWUP1101284 or #VXWUP3101284, respectively)

An RSSI test is done to determine if there is acceptable signal strength at a location be-

fore installing. The test also helps to place the antenna for the best reception. Where

the antenna receives the best signal will also determine where to mount the Telemeter.

NOTE: A High Gain Antenna should be on hand in the event that the included Mag-

netic Base Antenna is unable to pick up a sucient signal. A High Gain Antenna must

be purchased separately as it is not included with the kit.

1. At the machine location, plug the antenna’s cable into the ANTENNA port found

on the bottom of the G9 Telemeter. If a Card Reader is present, plug the serial

cable from the Card Reader into the Telemeter cable’s 6-pin black connector.

2. Disconnect the MDB connectors in the vending machine between the machine

control board and the bill acceptor and connect the MDB Cable* from the G9 Tele-

meter to the MDB connectors of the vending machine.

3. Place the antenna on top of, or inside the vending machine on a metal surface to

perform the test. Make sure the antenna is not surrounded by signal weakening

metal support brackets or located near the Telemeter or the control board when

the door is shut. This will improve connectivity to the cellular tower.

4. Wait until the Telemeter has initialized, which is indicated by a blinking green LED.

If a Card Reader is present the display will read “Swipe or Tap to Begin.”

5. To begin testing, press the Telemeter’s RSSI buton. The Telemeter’s

LEDs will indicate signal strength. And if present, the Card Reader’s

display will show CSQ: XX, YY; where XX is signal strength and YY is

Bit Error Rate. Use the following table to determine signal quality.

QUALITY TELEMETER LEDs CSQ: XX CSQ: YY

Very poor none 00 to 07

Any value other

than 00 for CSQ:YY

indicates addition-

al signal loss.

Poor RED 08 to 09

Good RED and YELLOW 10 to 14

Very good RED, YELLOW and GREEN 15 to 19

Excellent RED, YELLOW, GREEN and BLUE 20 or greater

6. If signal strength is poor or very poor, move the antenna to another location and

wait 15 seconds until the signal stabilizes and then recheck. If signal strength is

not strong enough with the normal Antenna, try the test with a High Gain An-

tenna.

7. Upon completion of testing, disconnect the G9 Telemeter’s MDB cable and recon-

nect the vending machine MDB connectors.

RSSI Button

*When a Bill Recycler is present, the ePort must be plugged into the MDB bus ahead of the

Bill Recycler to receive enough power to function properly.

2. RF/CARD SWIPE READER INSTALLATION

Install the Card Reader according to the design of the vending machine:

A Machine has a second opening for a bill acceptor - take note of screw sizes.

B Machine does not have a second opening for a bill acceptor.

C Machine has a POS window above the bill acceptor.

D Machine has a situation where a spacer is needed.

Vending machine has a second opening for a bill acceptor

1. Power down the vending machine door and remove

the blank plate that covers the opening.

2. Attach the Card Reader to the mounting plate using

the four, 8-32 x 3/8” mounting screws.

Correct screws must be used or the Card Reader

may be damaged and the warranty will be void.

3. Pass the assembly through the opening from inside

the door of the vending machine and secure the

mounting plate to the door with the original, blank plate screws.

Vending machine does not have a second opening for a bill acceptor

Mount the Card Reader on the outside surface of the vending machine:

1. Power down the vending machine door. If necessary, temporarily remove the bill

acceptor during the drilling and mounting of the Card Reader.

2. Use a small level and tape to secure the included Bezel Drilling template (Figure

1) where you want the Card Reader to be located, and mark the four mounting

screw holes and a hole for the cable.

4. Drill the four 3/16”holes for the mounting screws.

5. Drill the pilot hole for the 5/8”cable hole with a 3/8” bit and nish the hole by

using either a 41/64” Greenlee knockout punch (#7211BB-1/2) or a 1/4”–3/4” step

drill (McMaster-Carr part 8841A23).

6. Mount the Card Reader to the front of the door by using the four, 8-32 x 3/8”

mounting screws.

Vending machine has a POS window above the bill acceptor

If the vending machine (i.e. the Royal 660, Royal 804, or the Dixie 522) has a POS

window just above the bill acceptor (landscape doors), you must install the Card

Reader with the Security Plate (#V6XUE0520260). A Security Plate is not includ-

ed in the kit and can be purchased separately.

OPTIONAL SPACER

FIGURE 2

1. Power down the vending machine.

2. Remove the bill acceptor.

3. Remove the POS window above the bill

acceptor.

4. Route the serial cable attached to the back

of the Card Reader through the security

plate (Figure 3).

5. Secure the security plate to the Card

Reader with four, 8-32 x 3/8” mounting

screws (Figure 3).

6. Pass this assembly through the POS win-

dow opening from inside the vending ma-

chine door, and attach the security plate

to the door using the original hardware.

7. Replace the bill acceptor.

Vending machine has a situation where a spacer is needed

Some machines may require a spacer for the Card Reader to provide proper

clearance for card swipes. If this is the case, a spacer and four, 8-32 x 1” long screws are

available from USA Technologies by contact-

ing Customer Service at 888-561-4748. Re-

quest Spacer (#V6SUF1435002) and the four,

8-32 x 1” screws that are the correct length

for an installation with a spacer. A cost is as-

sociated with this part.

To complete the install, follow either the A,

B or C instructions above depending on the

design of the vending machine, and place

the spacer between the cardreader and plate

specic to the install and use the the four,

8-32 x 1” screws.

8-32 x 1”

screws

Alignment

Pins

SPACER

READER

FIGURE 4

Bezel

Adapter

Cable

8-32 x 3/8”

screws

SECURITY

PLATE

READER

FIGURE 3

Bezel

Adapter

Cable

3. INSTALL THE G9 TELEMETER

Follow these steps to install the G9 Telemeter in a vending machine:

1. Decide whether to mount the Telemeter using

the three supplied self-tapping screws (Figure

5), or with a strip of Velcro attached to the

back of the Telemeter.

2. Select a location in the main cabinet or door

where the Telemeter is accessible for service

and protected from moisture. To prevent any

water intrusion, mount the Telemeter verti-

cally with the cables hanging down. Make

sure it will not interfere with any moving parts

and allow for cable routing.

3. If mounting with screws, screw the self-

tapping screws into the frame of the door or

machine. If using Velcro, attach a strip of Velcro

to the frame of the door or machine and stick

the Telemeter to it.

4. Connect the Magnetic Base Antenna (#V8W-

UP0101278) MCX connector into the ANTENNA

ports found on the bottom of the Telemeter.

5. Place the antenna on top of, or inside the vend-

ing machine on a metal surface. Make sure the

antenna is not surrounded by signal weaken-

ing metal support brackets or located near the

Telemeter or the control board when the door

is shut. This will improve connectivity to the

cellular tower. (Figure 6).

5. Tie the antenna cable to the nearest cable from the Telemeter.

6. Disconnect the MDB connectors in the vending machine between the machine

Control Board and the existing payment devices. Connect the MDB Cable from

the G9 Telemeter to the MDB connectors going to the machine Control Board and

the existing payment devices. Ensure the connectors latch rmly together.*

7. Plug the 6-pin black connector from the Telemeter cable into the serial cable from

the Card Reader. Ensure the connectors latch rmly together.

8. Either connect the DEX cable with the standard jack plug from the Telemeter to

the vending machine DEX port (for remote DEX reporting), or leave the DEX cable

hanging loose if no remote DEX is to be used. Test all connections made.

FIGURE 5

FIGURE 6

*NOTE: When a Bill Recycler is present, the ePort must be plugged into the MDB bus

ahead of the Bill Recycler so that it can communicate properly with the VMC.

4. VERIFY THE INSTALLATION

1. Power up the vending machine and observe the LEDs of the G9 Telemeter. When

the green LED blinks, the Telemeter has initialized.

2. Once the Telemeter has initialized the HSPA Modem and connected to the wire-

less network, the Card Reader’s display should read “Swipe or Tap To Begin. “

3. At this point you can perform a test vend with a USA Technologies Pass Card or

credit card.

4. We recommend recording the ePort G9 Telemeter serial number and vending

machine ID for accounting purposes.

5. Contact USAT Customer Care if you have any questions – 888-561-4748.

You must have a signed ePort Connect Services Contract and bank account as-

signed to this device for it to be able to accept credit card transactions. Please

call USA Technologies Customer Care at 888-561-4748, if you need activation

documents.

DEX Cable Serial Cable MDB Cable

FIGURE 7 G9 C0NTROLLER CABLES

USA TECHNOLOGIES CUSTOMER CARE

Contact USA Technologies Customer Care for technical support and to request

additional parts, information, and pre-authorization forms.

Phone: 888.561.4748

FAX: 610.989.9695

Email: [email protected]

Online Store: http://store.usatech.com

USA TECHNOLOGIES WEBSITE ADDRESSES

3103 Phoenixville Pike

Malvern, PA 19355

#VVXUD0101911 REV D

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference that may cause

undesired operation.

Customer Website Login

https://usalive.usatech.com

Company Site

http://www.usatech.com

Andere Handbücher für ePort G9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere USA Technologies Zahlungsterminal Handbücher

USA Technologies

USA Technologies ePort G10-S Bedienungsanleitung

Beliebte Zahlungsterminal Handbücher anderer Marken

PAX

PAX D180SRF Bedienungsanleitung

LinkPoint

LinkPoint AIO Bedienungsanleitung

Moneris

Moneris hispeed 6200 Bedienungsanleitung

Moneris

Moneris iWL220 Bedienungsanleitung

Ingenico

Ingenico iUC280 Bedienungsanleitung

Ingenico

Ingenico Tetra Move/5000 Bedienungsanleitung

Ingenico

Ingenico iWL250B Bedienungsanleitung

Optimum

Optimum M4230 Bedienungsanleitung

Triton

Triton RL5000 Bedienungsanleitung

Ingenico group

Ingenico group Lane/8000 Bedienungsanleitung

Gilbarco

Gilbarco FlexPay IV CRIND Installations- und Betriebshandbuch

Infinite Peripherals

Infinite Peripherals Infinea Tab Lite Bedienungsanleitung

PAX

PAX S920 Bedienungsanleitung

Ingenico

Ingenico iCT220, iCT250 Bedienungsanleitung

dejavoo

dejavoo Z Series Bedienungsanleitung

VeriFone

VeriFone VX 520 Series Bedienungsanleitung

Optomany

Optomany axept S900 Bedienungsanleitung

Skyzer

Skyzer iWL252 BLUETOOTH Bedienungsanleitung

USA Technologies ePort G9 Bedienungsanleitung

Beliebte Zahlungsterminal Handbücher anderer Marken