UWE AM-3000 Bedienungsanleitung

AM SERIES

ELECTRONIC WEIGHING SCALE

OPERATION MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPT TO OPERATE THE SCALE

DECEMBER 1999

Specifications subject to change without prior notice

CONTENTS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYBOARD LAYOUT AND DESCRIPTION

4. INITIAL SETUP

5. INSTRUCTION FOR USE

6. TROUBLE SHOOTING

7. DAILY CARE AND MAINTENANCE

1. INSTALLATION

1.1 Check and make sure that the following

accessories are included:

This operation manual

Scale x 1

Platter x 1

Power adaptor x 1

Dust cover x 1

Contact your dealer if any item missed.

1.2 Inserttheplatterintothescalecarefully.

No excessive force is required.

1.3 Power on the scale

a. Before plugging the power adaptor into

electricity outlet, check and make sure

that the input voltage of power adaptor

matches with the output voltage of the

outlet. If not, do not plug in the adaptor,

contact your dealer immediately.

b. Before first time use, plug the main

adaptor into the wall outlet and charge

the scale for at least 8 hours.

c. Retain the packing materials for future

transportation purposes.

Caution:

This unit is legal for trade only when it is

sealed (and/or stamped) and bearing a serial

number. Do not attempt to break the seal (or

stamp) affixed to this scale or remove the

serial number. Contact your dealer for more

information and after sales service.

For most accurate weighing result, do not use

this scale in where or when the environment

condition falls beyond as those listed on

SPECIFICATIONS.

Do not attempt to open this unit or conduct

any trouble shootings other than those listed

on TROUBLE SHOOTING.

2. SPECIFICATIONS

Model No. AM-3000

AM-6000

AM-15K AM-30K

Capacity 3000g 6000g 15kg 30kg

Division 1g 2g 0.005kg

0.01kg

Tare Range 999g 1998g 4.995kg

9.990kg

Power-

on Zero

Range ¡Ó300g

¡Ó600g

¡Ó1.5kg

¡Ó3.0kg

Zero Range ¡Ó60g

¡Ó120g

¡Ó0.3kg

¡Ó0.6kg

Min. Load 20g 40g 0.1kg 0.2kg

Operation

Environment 0o~40oC (32o~104oF),

Non-condensed. R.H.¡Ø85%

Power source By Built-

in rechargeable battery or

power adaptor

Specifications subject to change without notice.

NOTE

To comply with the law of certain countries

and certain approval requirements, the

avoirdupois weight units may be disabled.

Contact your dealer for more information.

3. KEYBOARD LAYOUT AND DESCRIPTION

1. ON/ZERO KEY

Press this key to turn scale on or reset

display value to zero.

2. TARE KEY

Press this key to tare off the weight of

a container.

3. MODE KEY

Press this key to shift among different

weight units and/or turn backlight on/off.

4. OFF KEY

Press this key to turn scale off.

5. IN-CHARGE INDICATOR

Red color: Recharging battery

Green color: Charging completed

6. ZERO INDICATOR

An arrow will appear and point at this sign

to indicate a zero weight status.

7. TARE INDICATOR

An arrow will appear and point at this sign

to indicate the tare function is in

operation and weight displayed is net

weight.

8. LO-BAT INDICATOR

When this indicator appears, recharge the

scale immediately. Failure to do so may

cause unrecoverable damage to the

rechargeable battery inside scale.

4. INITIAL SETUP

4.1 Placing the Scale

In order to obtain an accurate weighing

result, the scale must be placed on a strong

and level surface.

If required, adjust the adjustable feet

underneath scale to obtain a level position.

Refer to the bubble indicator for leveling

condition.

4.2 Internal Setting

4.2.1 Select weight unit

The scale is equipped with metric and

avoirdupois weight units. Default setting

= metric weight unit only. Follow the below

steps to enable/disable the avoirdupois

units.

a. Turn scale off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE twice

e. Scale displays F.3

f. Press and hold MODE until the kg or lb

sign appears.

g. Press MODE to shift between kg and lb

sign.

-To enable the avoirdupois units,

press ON/ZERO when the lb sign

appears.

-To disable the avoirdupois units,

press ON/ZERO when the kg sign

appears.

h. After ON/ZERO is pressed, the scale will

return to operation status.

NOTE

To comply with the law of certain countries

and certain approval requirements, the

avoirdupois weight units may be disabled.

Contact your dealer for more information.

4.2.2 Select Auto Power Off Setting

The scale is equipped with Auto Power Off

Function. The scale will be turned off

automatically if it is not used for 4 minutes.

Follow the below steps to enable/disable

Auto Power Off Function

a. Turn scale off

b. Press and hold TARE, then press ON/ZERO

c. Scale displays F.1

d. Press TARE three times

e. Scale displays F.4

f. Press MODE to shift between 0._OFF and

4._OFF.

g. To enable Auto Power Off Function, press

ON/ZERO when 4._OFF appears.

h. To disable AutoPowerOffFunction, press

ON/ZERO when 0._OFF appears.

i. After ON/ZERO is pressed, the scale will

return to operation status.

5. INSTRUCTION FOR USE

5.1 Before Weighing

Make sure that:

a. The platter is inserted firmly into the

scale

b. The scale is placed on a level and strong

surface.

c. The scale is turned on.

d. The ZERO INDICATOR is on. If not, press

ZERO/ON to set display to zero.

5.2 Weighing

a. Always place an object onto the platter

gently. Excessive force applied to platter

may cause damages to sensor inside scale.

b. The weight of the object would be displayed

automatically.

c. It is a good practice to remove all loads

from platter after weighing. It would

prolong the lifetime of scale.

5.3 Select Weight Unit

Press MODE to shift among kg àdecimal àlb/oz.

àkg weight units. Refer to 4.2.1 for internal

setting procedures.

The weight unit used before power off would

be employed when the scale is turned on again.

5.4 Turn Backlight (Optional) On/Off

Press MODE to shift among various weight units

with backlight or without backlight.

Even though the backlight function is employed,

backlight will be automatically turned off when

a zero weight is detected and remains stable

for 2 seconds

Backlight will be automatically turned on again

when a weight is detected.

5.5 Set Displayed Value to Zero when Unloaded

Pressing the ON/ZERO can eliminate a positive

or negative value. After the ON/ZERO is pressed,

the ZERO INDICATOR appears.

Refer to SPECIFICATIONSfor maximum zero range.

5.6 Tare off the Weight of a Container

When a container is used, follow the below steps

to tare off the weight of the container and

get the net weight.

a. Remove all loads away from platter

b. Make sure that the ZERO INDICATOR is on.

c. Place the container on the platter.

d. Press TARE.

After TARE is pressed, the TARE INDICATOR would

appear.

Refer to 5.2 for weighing procedures. Weight

displayed under is the net weight of the subject

matter. Refer to SPECIFICATIONS for maximum

tare range.

5.7 Clear the TARE Function

Remove all loads from platter then press TARE.

After TARE is pressed, the TARE INDICATOR would

disappear.

5.8 Recharge the Scale

The scale is equipped with a built-in

rechargeable battery. When the LO-BAT

INDICATOR appears, recharge the scale

immediately. Failure to do so may cause

unrecoverable damage to the rechargeable

battery.

The scale can remain in operation when being

recharged.

Charging is completed when the color of the

IN-CHARGE INDICATOR turns green.

6. TROUBLE SHOOTING

Syndrome Scale cannot be turned on

Check: Is the scale charged?

Action: Recharge the scale for at least 8

hours before first time use or plug

in the power adaptor before power

on the scale.

Check Is the power adaptor inserted

properly into both the electricity

outlet and the DC inlet of scale.

Action: Secure both ends of the power adaptor

and try again.

Syndrome Scale turned off automatically

Check Is Auto Power Off Function employed?

Action Refer to 4.2.2 to disable Auto Power

Off Function.

Check Is the LO-BAT INDICATOR on?

Action Apply the power adaptor.

Syndrome Rated capacity cannot be reached

Check Is the TARE INDICATOR on?

Action: Turn the scale off. Remove all loads

from platter and turn on again.

Check Is there anything obstructing the

platter?

Action Remove all obstacles.

Syndrome Blank display with only "kg" or "lb"

Check Is the load applied to platter excess

the rated capacity of scale?

Action Remove all loads from platter and

try again.

Syndrome Scale displays -----

Check Is the platter inserted to the scale

correctly?

Action Insert the platter to scale

correctly.

Check Is the stainless steel platter cover

placed on the platter?

Action Place the stainless steel platter

cover onto the platter.

Syndrome Weighing result is not accurate

Check Is the scale placed in a level

condition?

Action Adjust the adjustable feet to a level

condition.

Check Is the scale affected by airflow,

vibration or RFI?

Action: Place the scale away from all

disturbances.

Check Is the scale calibrated correctly?

Action Contact your dealer.

Check Is the correct weight unit employed?

Action Refer to 4.2.1 and 5.3 for weight

unit setting and usage.

7. DAILY CARE AND MAINTENANCE

7.1 Cleanthescalewithasoftanddampcloth.

If necessary, apply a mild detergent.

7.2 Do not use any harsh, abrasive material,

acetone, volatile solvent, thinner or

alcohol for cleaning.

7.3 Verify the accuracy of scale

periodically.Re-calibratethescaleif

necessary.

Note: In some countries, calibration is

restricted to be done by an

authorized/qualified agent only.

Contact your dealer for more

information.

7.4 It is a good practice to apply the dust

cover when operating the scale.

7.5 The scale must be placed horizontally

during transportation or long time

storage.

7.6 Remove platter from scale before

transportation or long time storage.

7.7 Store scale in a dry and clean place.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere UWE Skala Handbücher

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung