UWE FS-60 Bedienungsanleitung

FS SERIES

All STAINLESS STEEL ELECTRONIC FLOOR SCALE

OPERATION MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE

ATTEMPTING TO OPERATE THE SCALE

APRIL 1998

Specifications subject to change without prior notice

CONTENTS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYBOARD LAYOUT AND DESCRIPTION

4. INITIAL SETUP

5. INSTRUCTION FOR USE

6. TROUBLE SHOOTING

7. DAILY CARE AND MAINTENANCE

APPENDIX

Installation Diagram

1. INSTALLATION

1.1 Check and make sure that the following

accessories are included:

This operation manual

Indicator x 1

Platform x 1

Pillar x 1

Power adaptor x 1

Screws and tool set x 1

Contact your dealer if any item missed.

1.2 Install the scale very carefully. Refer

to Appendix INSTALLATION DIAGRAM for

installation method and procedures.

Should you encounter any problem in

installation, contact your dealer.

1.3 Power on the scale

a. Before plugging the power adaptor into

electricity outlet, check and make sure

that the input voltage of power adaptor

matches with the output voltage of the

outlet. If not, donot plug in the adaptor,

contact your dealer immediately.

b. Before first time use, plug the main

adaptor into the wall outlet and charge

the scale for at least 8 hours.

c. Retain the packing materials for future

transportation purposes.

Caution:

In most cases, this unit is legal for trade

only when it is sealed and bearing a serial

number. Do not attempt to break the seal or

remove the serial number. Contact your dealer

for more information or after sales service.

2. SPECIFICATIONS

Model No. Capacity Division

FS-60 60kg 0.01kg

FS-150 150kg 0.02kg

FS-300 300kg 0.05kgg

Platform size 425 x 525 mm

Power source Built-in rechargeable

battery or power adaptor

Max. Tare range

Up to 100% of rated capacity

Max. Zero range Up to 2% rated capacity

Weight Units

(Note A) Metric, decimal pound

and pound/ounce

Operation

Environment 0o~40oC (32o~104oF),

Non-condensed. R.H.?85%

Specifications subject to change without notice.

Note A:

To comply with the law of certain countries,

the avoirdupois weight units may be disabled.

Contact your dealer for more information.

3. KEYBOARD LAYOUT AND DESCRIPTION

1. ON/OFF KEY

Press this key to turn scale on or off.

2. MODE KEY

Press this key to switch among metric and

avoirdupois weight units with or without

backlight (optional).

3. M+ KEY

Press this key to enter present weight value

into memory.

4. MR KEY

Press this key to recall the accumulated weight

value in memory.

5. TARE KEY

Press this key to tare off the weight of a

container and get the net weighing result.

6. ZERO KEY

Press this key to reset weight displayed to

zero when unloaded.

7. MC KEY

Press the MR and TARE key simultaneously to

clear all data in memory.

8. ZERO INDICATOR

An arrow will appear and point at this sign

to indicate a zero weight status.

9. TARE INDICATOR

An arrow will appear and point at this sign

when the tare function is being employed.

10. M+ INDICATOR

An arrow will appear and point at this sign

when the memory contains data.

11. WEIGHT UNIT INDICATOR

"kg" indicates the metric unit is being

employed.

"lb" indicates the avoirdupois unit is being

employed.

12. LO-BAT INDICATOR

When this indicator appears, rechargethe scale

immediately. Failure to do so may cause

unrecoverable damages to the rechargeable

battery inside.

13. IN-CHARGE INDICATOR

Red color: Recharging battery

Green color: Charging completed

4. INITIAL SETUP

4.1 Placing the Scale

Placethescaleonahard and strong surface,

where is free from RF interference,

vibration, fire, direct sunlight and

excessive moisture. For accurate weighing,

always place this unit on a level surface.

If required, adjust the adjustable feet

underneath scale to obtain a level

position.

4.2 Internal Setting

4.2.1 Select weight unit

The scale is equipped with metric and

avoirdupois weight units. Follow the below

steps to enable/disable the avoirdupois

units.

a. Turn scale off

b. Press and hold TARE, then press ON/OFF

c. Scale displays F.1

d. Press TARE twice

e. Scale display F.3

f. Press and hold MODE until the kg or lb

sign appears.

g. Press MODE to shift between kg and lb

sign.

h. To enable the avoirdupois units, press

ZERO when the lb sign appears.

i. To disable the avoirdupois units, press

ZERO when the kg sign appears.

j. After ZERO is pressed, the scale will

return to operation status.

4.2.2 Select Auto Power Off Setting

The scale is equipped with Auto Power Off

function. The scale will be turned off

automatically if it is not used for 4 minutes.

Follow the below steps to enable/disable

the Auto Power Off function

a. Turn scale off

b. Press and hold TARE, then press ON/OFF

c. Scale displays F.1

d. Press TARE three times

e. Scale display F.4

f. Press MODE to shift between 0._OFF and

4._OFF.

g. To enable the Auto Power Off function,

press ZERO when 4._OFF appears.

h. To disable the Auto Power Off function,

press ZERO when 0._OFF appears.

i. After the ZERO is pressed, the scale will

return to operation status.

5. INSTRUCTION FOR USE

5.1 Before Weighing

Make sure that:

a. The upper platform cover is inserted firmly

into the platform.

b. The scale is placed on a level and strong

surface.

c. The scale is turned on.

d. The ZERO indicator is on. If not, press ZERO

key to set display to zero.

5.2 Weighing

a. Always place an object onto the platform

gently. Excessive force applied to platform

may cause damages to sensor inside.

b. The weight of the object would be displayed

automatically.

c. It is a good practice to remove all loads

from platform after weighing. It would

prolong the lifetime of scale.

5.3 Select Weight Unit

Press MODE to shift among kg àdecimal àlb/oz.

àkg weight units. Refer to 4.2.1 for internal

setting procedures.

The weight unit used before power off would

be employed when the scale is turned on again.

5.4 Turn Backlight (Optional) On/Off

Press MODE to shift among various weight units

with backlight or without backlight.

Eventhoughthebacklight function isemployed,

backlight will be automatically turned off when

a zero weight is detected and remains stable

for 5 seconds

Backlight will be automatically turned on again

when a weight is detected.

5.5 Set Displayed Value to Zero when Unloaded

A positive or negative value can be eliminated

by pressing the ZERO key. After the ZERO key

is pressed, the ZERO indicator would appear.

RefertoSPECIFICATIONS formaximumzerorange.

5.6 Tare off the Weight of a Container

When a container is used, follow the below steps

to tare off the weight of the container and

get the net weight result.

a. Remove all loads away from platform.

b. Make sure that the ZERO indicator is on.

c. Place the container on the platform.

d. Press TARE key.

After the TARE key is pressed, the TARE

indicator would appear.

Refer to 5.2 for weighing procedures. Weight

displayed under this tare mode is the net weight

of the object. Refer to SPECIFICATIONS for

maximum tare range.

5.7 Clear the TARE Function

Remove all loads from platform then press TARE.

After the TARE key is pressed, the TARE

indicator would disappear.

5.8 Bulky Weighting

The pillar can be extended for bulky weighing.

Refer to Appendix Installation diagram for

pillar extension.

5.9 Weight Memory Function

a. To save a weight to memory and auto weight

accumulation

When weight display is stable, press M+ to

save the weight into memory. Scale displays

P. 1 and the M+ indicator appears indicating

total number of entry and the memory is

containing data.

b. Recall accumulated weight in memory

PressMR.Scale willdisplaythetotalnumber

of entry and the total accumulated weight

of all entries.

c. Clear data in memory

Press and hold MR, then press TARE key after

the accumulated weight is being displayed.

Scale will display P.0 to indicate all data

in memory has been erased.

Caution

All data stored in memory will be erased if:

a. The scale is turned off, or,

b. The weight unit is changed.

5.10 Recharge the Scale

The scale is equipped with a built-in

rechargeable battery. When the LO-BAT

indicator appears, recharge the scale

immediately. Failure to do so may cause

unrecoverable damages to the rechargeable

battery.

The scale can remain in operation when being

recharged.

Charging is completed when the color of the

IN-CHARGE indicator turns green.

Caution:

Insert the rubber cap into the DC inlet of scale

except during battery recharging.

6. TROUBLE SHOOTING

Syndrome Scale cannot be turned on

Check: Is the scale charged?

Action: Recharge the scale for at least 8

hours before first time use or plug

in the power adaptor before power

on the scale.

Check Is the power adaptor inserted

properly into both the electricity

outlet and the DC inlet of scale.

Action: Securebothendsofthepoweradaptor

and try again.

Syndrome Scale turned off automatically

Check Is the Auto Power Off function

employed?

Action Refer to 4.2.2 to disable the Auto

Power Off function.

Check Is the LO-BAT indicator on?

Action Apply the power adaptor.

Syndrome Rated capacity cannot be reached

Check Is the TARE indicator on?

Action: Turn the scale off. Remove all loads

from platform and turn on again.

Check Is there anything obstructing the

platform or pillar?

Action Remove all obstacles.

Syndrome Scale displays 00000

Check Does the load applied to platform

excess the rated capacity of scale?

Action Remove all loads from platform and

try again.

Syndrome Weighing result is not accurate

Check Is the scale placed in a level

condition?

Action Adjust the adjustable feet to a level

condition.

Check Is the scale affected by airflow,

vibration or RFI?

Action: Place the scale away from all

disturbances.

Check Is the scale calibrated correctly?

Action Contact your dealer.

Check Is the correct weight unit employed?

Action Refer to 4.2.1 and 5.3 for weight

unit setting and usage.

7. DAILY CARE AND MAINTENANCE

7.1 Clean the scale with a soft and damp cloth.

If necessary, apply a mild detergent.

7.2 Donotuseanyhigh-pressure water spray,

harsh, abrasive material, acetone,

volatile solvent, thinner or alcohol

for cleaning.

7.3 Verify the accuracy of scale

periodically. Re-calibratethescaleif

necessary.

Note: In some countries, calibration is

restricted to be done by an

authorized/qualified agent only.

Contact your dealer for more

information.

7.4 The scale must be placed horizontally

during transportation or long time

storage.

7.5 Store scale in a dry and clean place.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere UWE Skala Handbücher

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung