UWE APM Bedienungsanleitung

CONTENTS

1. INSTALLATION

2. SPECIFICATIONS

3. KEYBOARD LAYOUT AND DESCRIPTION

4. INITIAL SETUP

5. INSTRUCTION FOR USE

6. TROUBLE SHOOTING

7. DAILY CARE AND MAINTENANCE

APPENDIX: ERROR CODES

INSTALLATION

Because of metrological legislation, installation/some

metrological parameter settings are limited to be done

by authorized personnel only. Do not attempt to change

any of the built-in parameters. Contact your dealer for

installation and technical assistance.

CAUTION:

This unit is legal for trade only when it is sealed (and/or

stamped) and bearing a serial number. Do not attempt

to break the seal (or stamp) affixed to this indicator

or remove the serial number. Contact your dealer for

more information and after sales service.

For most accurate weighing result, do not use the

indicator in where or when the environment condition

falls beyond as those listed on SPECIFICATIONS.

Do not attempt to open this unit or conduct any trouble

shootings other than those listed on TROUBLE SHOOTING.

2. SPECIFICATIONS

Model No.

APM INDICATOR

Max.

USER DEFINED

nmax

6000

Tare Range

1/3 Max. –e (NOTE 1)

Power-on Zero Range

±20% Max. (NOTE 1)

Zero Range

±2% Max. (NOTE 1)

Min. Load

20e (NOTE 1)

Max. measuring range

9.0mV

Min. signal voltage per

verification scale interval

0.8 V

Power voltage requirements

6.0 VDC (BY EXTERNAL POWER

ADAPTOR OR RECHARGEABLE

BATTERY)

Minimum battery voltage

5.5 VDC

Load cell Excitation voltage

5 VDC

Minimal load cell impedance

85

Maximal load cell impedance

5000

Load cell connection

4-wire

Operation

Environment

-10o~40oC

Non-condensed. R.H.≦85%

Specifications subject to change without notice.

NOTE 1:

For Multi range or interval, change e to e1.

CAUTION:

To comply with the law of certain countries and certain

approval requirements, the avoirdupois weight unit of

this indicator may be disabled.

3. KEYBOARD LAYOUT AND DESCRIPTION

1. ON/OFF KEY

Press this key to turn indicator on or off.

2. MODE KEY

Press this key to shift among different weight units

and/or turn backlight on/off.

3. TARE KEY

Press this key to tare off the weight of a container.

4. ZERO KEY

Press this key to set weight displayed to zero.

5. M+ KEY

Press this key to accumulate current weight to memory.

6. MR KEY

Press this key to recall the total accumulated weight

from memory.

7. MC KEY

Press MR and ZERO simultaneously to clear weight from

memory.

8. LO BAT INDICATOR

This indicator appears when input voltage is below the

lowest input limit. Check the power supplied to the

indicator.

9. ZERO INDICATOR

This indicator appears to indicate zero weight status.

10. NET INDICATOR

This indicator appears to indicate the tare function

is in operation and weight shown is net weight.

11. M+ INDICATOR

This indicator appears to indicate memory contains of

stored data.

12. MR INDICATOR

This indicator appears to indicate the value shown is

the total accumulated weight stored.

13. WEIGHT UNIT INDICATOR

The current weight unit is displayed here.

4. INITIAL SETUP

4.1 PLACING THE SCALE

In order to obtain an accurate weighing result, the

complete weighing instrument (hereinafter referred as

the scale) must be placed on a strong and level surface.

4.2 INTERNAL SETTING

4.2.1 Select Weight Unit

This indicator is equipped with metric and avoirdupois

weight units. Default setting = metric weight unit only.

Follow the below steps to enable/disable the avoirdupois

units.

a. Turn indicator off

b. Press and hold TARE, then press ON/OFF

c. Indicator displays F.1

d. Press TARE twice

e. Indicator displays F.3

f. Press and hold MODE until the kg or lb sign appears.

g. Press MODE to shift between kg and lb sign.

- To enable the avoirdupois units, press TARE

when the lb sign appears.

- To disable the avoirdupois units, press TARE

when the kg sign appears.

h. After TARE is pressed, the indicator will go to F4

(AUTO POWER OFF setting). Refer to 4.2.2 for AUTO

POWER OFF setting or press ZERO to quit.

NOTE

To comply with the law of certain countries and certain

approval requirements, the avoirdupois weight units may

be disabled. Contact your dealer for more information.

4.2.2 Select Auto Power Off Setting

The indicator is equipped with Auto Power Off Function.

The indicator will be turned off automatically if it

is not used for 4 minutes. Follow the below steps to

enable/disable Auto Power Off Function

a. Turn indicator off

b. Press and hold TARE, then press ON/OFF

c. Indicator displays F.1

d. Press TARE three times

e. Indicator displays F.4

f. Press MODE to shift between 0._OFF and 4._OFF.

-To enable Auto Power Off Function, press TARE then

ZERO when 4._OFF appears.

-To disable Auto Power Off Function, press TARE

then ZERO when 0._OFF appears.

g. After TARE then ZERO are pressed, the indicator will

return to operation status.

5. INSTRUCTION FOR USE

5.1 BEFORE WEIGHING

Make sure that:

a. Connect the load cell signal and power to the

indicator properly.

b. Place the scale on a level and strong surface.

c. The indicator is turned on.

d. The ZERO INDICATOR is on. If not, press ZERO to set

display to zero.

5.2 WEIGHING

a. Always place an object onto the scale gently.

Excessive force applied to platter may cause damages

to weight sensor.

b. The weight of the object is displayed on the indicator

automatically.

c. It is a good practice to remove all loads from scale

after weighing. It would prolong the lifetime of

weight sensor.

5.3 SELECT WEIGHT UNIT

Press MODE to shift among kg decimal lb/oz. kg

weight units. Refer to 4.2.1 for internal setting

procedures.

The weight unit used before power off would be employed

when the indicator is turned on again.

5.4 TURN BACKLIGHT (OPTIONAL) ON/OFF

Press MODE to shift among various weight units with or

without backlight.

Even though the backlight function is employed,

backlight will be automatically turned off when a stable

weight remained for 25 seconds or a zero weight is

detected and remains stable for 10 seconds

Backlight will be automatically turned on again when

a new weight is detected or when any key is pressed.

5.5 SET DISPLAYED VALUE TO ZERO WHEN UNLOADED

By pressing ZERO, weight displayed will be set to zero

and ZERO INDICATOR appears.

Refer to SPECIFICATIONS for maximum zero range.

5.6 TARE OFF THE WEIGHT OF A CONTAINER

When a container is used, follow the below steps to tare

off the weight of the container and get the net weight.

Inhaltsverzeichnis

Andere UWE Skala Handbücher

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung