V.link CI-RL4-MIB3-E Bedienungsanleitung

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Video-inserter

CI-RL4-MIB3-E

Compatible with

VW vehicles with

MIB3 Entry - Composition with 8.25inch monitor

Seat vehicles with

MIB3 Entry - with 8.25inch monitor

Skoda vehicles with

MIB3 Entry with 8.25inch monitor

Video-inserter for front- and rear-view camera

and two additional video sources

Product features

Video-inserter for factory-infotainment systems

1 CVBS Input for rear-view camera

1 CVBS Input for front camera

2 CVBS video-inputs for after-market devices (e.g. USB-Player, DVB-T2 tuner)

Automatic switching to rear-view camera input on engagement of the reverse gear

Automatic front camera switching after reverse gear for 10 seconds

Activatable parking guide lines for rear-view camera (not available for all vehicles)

Video-in-motion (ONLY for connected video-sources)

Video-inputs NTSC and PAL compatible

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page2

Contents

1. Prior to installation

1.1. Delivery contents

1.2. Checking the interface compatibility of vehicle and accessories

1.3. Connectors - video interface

1.4. Connectors - daughter PCB

1.5. Dip-switch settings

1.5.1. 8 dip –black

1.5.1.1. Activating the front camera input (dip 1)

1.5.1.2. Enabling the interface’s video inputs (dip 2-3)

1.5.1.3. Rear-view camera setting (dip 5)

1.5.2. 4 dip - red

2. Installation

2.1. Place of installation

2.2. Connection scheme

2.3. Installation –Daughter PCB

2.3.1. Head units with DIN housing

2.3.2. Special case: Head units without DIN housing

2.3.3. Warning notes, concerning the installation of ribbon cables

2.4. Connection –20pin picture signal cable

2.5. Connection –10pin Power / CAN cable

2.6. Analogue power supply

2.7. Power supply output

2.8. Connection –video inputs

2.8.1. Audio insertion

2.8.2. After-market front camera

2.8.3. After-market rear-view camera

2.8.3.1. Case 1: Interface receives the reverse gear signal

2.8.3.2. Case 2: Interface does not receive the reverse gear signal

2.9. Connection –external keypad

3. Interface operation by external keypad

4. Picture settings

5. Specifications

6. Frequently asked questions

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page3

Legal Information

By law, watching moving pictures while driving is prohibited, the driver must not be

distracted. We do not accept any liability for material damage or personal injury resulting,

directly or indirectly, from installation or operation of this product. This product should only

be used while standing or to display fixed menus or rear-view-camera video when the

vehicle is moving, for example the MP3 menu for DVD upgrades.

Changes/updates of the vehicle’s software can cause malfunctions of the interface. We

offer free software-updates for our interfaces for one year after purchase. To receive a free

update, the interface must be sent in at own cost. Labour cost for and other expenses

involved with the software-updates will not be refunded.

1. Prior toinstallation

Read the manual prior to installation.

Technical knowledge is necessary for installation. The place of installation has to be free of

moisture and away from heat sources.

1.1. Delivery contents

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page4

Requirements

Brand

Compatiblevehicles

Compatiblesystems

Seat/Cupra

Arona (KJ7) sincemodelyear2022

Ateca (KH7) sincemodelyear2021

Ibiza5 (KJ) sincemodelyear2022

Tarraco (KN2) since12/2018

MIB3 Entry infotainment

with 8.25inch monitor

Skoda

Fabia 4 (PJ) ab 09/2021

Octavia4 (NX) since07/2019

Scala (NW1) since01/2019

MIB3 Entry - Compositioninfotainment

with 8.25inch monitor

Caddy5 (SB) since11/2020

Golf8 (CD) since12/2019

MIB3 Entry –Composition infotainment

with DIN cage behind 8.25inch monitor

or MIB3 Entry - Composition 825 short version

without DIN cage behind 8.25inch monitor

Limitations

Insertedvideopicture In theinsertedvideopicture (front andrearviewcamera, video 1 andvideo 2)

a 5mm wideblackstripremains on bothsidesthatcannotbefaded out.

Video only The interface inserts ONLY video signals into the infotainment.

For inserting Audio signals either the possibly existing factory audio-AUX-input or

a FM-modulator can be used.

In case that 2 AV sources shall be connected, a desired audio switching will

require additional electronic.

Factory rear-view camera Automatically switching-back from inserted video to factory rear-view camera is

only possible while the reverse gear is engaged. To delay the switch-back an

additional electronic part is required.

After market front camera The front camera will automatically be switched for 10 seconds after disengaging

the reverse gear. A manually front camera switching is possible by external

keypad.

Guidelines Displayed guidelines are not available in all vehicles.

1.2. Checking the compatibility of vehicle and accessories

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page5

1.3. connectors - video-interface

The video-interface (daughter PCB) converts the video signals of connected after-market

sources in a factory monitor compatible picture signal which is inserted in the factory

monitor, by using separate trigger options.

1.4. connectors–daughter PCB

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page6

1.5. Dip-switch settings

1.5.1. 8 dip - black

Some settings have to be selected by the dip-switches on the

video interface.

Dip position down is ON and position up is OFF.

*The front camera will automatically be switched for 10 seconds after disengaging the

reverse gear (see following information).

After each Dip-switch-change a power-reset of the Video Interface has to be performed!

1.5.1.1. Activating the front camera input (dip 1)

If set to ON, the interface switches for 10 seconds from the rear-view camera to the front

camera input after having disengaged the reverse gear. In addition, a manual switch-over to

the front camera input is possible via keypad (short press) from any image mode.

Description of the front camera power supply: see chapter “Power supply output”.

1.5.1.2. Enabling the interface’s video inputs (dip 2-3)

Only the enabled video inputs can be accessed when switching through the interface’s video

sources. It is recommended to enable only the required inputs, disabled inputs

will be skipped when switching through the video-interfaces inputs.

Dip

Function

ON (down)

OFF (up)

Front camera

enabled*

disabled

Power supply

output

(red wire)

+12V (max. 3A) when reverse gear

is engaged incl. 10 seconds delay

and +12V by manual switching to

front camera by keypad

+12V (max. 3A) ACC

CVBS AV1-input

enabled

disabled

CVBS AV2-input

enabled

disabled

No function

Set to OFF

Rear-view cam type

after-market

factory or none

No function

Set to OFF

No function

Set to OFF

No function

Set to OFF

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page7

1.5.1.3. Rear-view camera setting (dip 5)

If set to OFF, the interface switches to factory picture while the reverse gear is engaged to

display factory rear-view camera.

If set to ON, the interface switches to its rear-view camera input „V4 Reverse“ while the

reverse gear is engaged.

Note: Dip 4, 6, 7and 8 are out of function and have to be set to OFF.

After each Dip-switch-change a power-reset of the Video Interface has to be performed!

1.5.2. 4 dip - red

By using the Dip-switches, the factory Head-unit or vehicle can be chosenwhich the interface

will be connected to.

Dip position down is ON and position up is OFF.

Set all dip switches to off

Vehicle/Navigation

Dip 1

Dip 2

Dip 3

Dip 4

All vehicles

OFF

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page8

2. Installation

Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent

12V source. If according to factory rules disconnecting the battery is to be avoided, it is

usually sufficient to put the vehicle to“Sleep-Mode”. In case it does not succeed,

disconnect the battery with a resistor lead.

If power source is not taken directly from the battery, the connection has to be checked

for being start-up proven and permanent.

2.1. Place ofinstallation

The video interface is designated to be connected behind the vehicle`s head unit.

The daughter PCB is prepared to be connected inside the factory head unit).

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page9

2.2. Connection scheme

Version 15.07.2022 HW CAM(V100) / (V11.3) CI-RL4-MIB3-E

Page10

2.3. Installation –daughter PCB

2.3.1. Head units with DIN housing

Remove the factory monitor and open it`s housing. The daughter PCB is built to be installed

into the optical lead between the monitor panel and mainboard of the vehicles monitor.

Inhaltsverzeichnis

Andere v.link Autozubehör Handbücher

v.link

v.link VL2-LR14-OPS Bedienungsanleitung

v.link

v.link VL2-N902 Bedienungsanleitung

v.link

v.link VL2-MBN2 Bedienungsanleitung

v.link

v.link VL2-DVD900 Bedienungsanleitung

v.link

v.link VL2-FORD-02 Bedienungsanleitung

v.link

v.link CI-VL2-DVD900 Bedienungsanleitung

v.link

v.link VL2-CIC Bedienungsanleitung

v.link

v.link CI-VL2-MBN45 Bedienungsanleitung

v.link

v.link VL2-PC-HSD Bedienungsanleitung

v.link

v.link VL7-NBT2 Bedienungsanleitung

v.link

v.link CI-VL7-MGU Bedienungsanleitung

v.link

v.link VL2-DVD800 Bedienungsanleitung

v.link

v.link VL2-NG4-HU Bedienungsanleitung

v.link

v.link VL2-GVIF Bedienungsanleitung

v.link

v.link CI-VL2-CONCERT Bedienungsanleitung

v.link

v.link VL3-SC15 Bedienungsanleitung

v.link

v.link VL2-UCON8-SM Bedienungsanleitung

v.link

v.link VL2-MBN2 Bedienungsanleitung

v.link

v.link VL2-CONCERT Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

v.link

v.link VL3-UCON5-F Bedienungsanleitung

v.link

v.link CI-VL2-NG4-HU Bedienungsanleitung

v.link

v.link CI-VL3-R40-E Bedienungsanleitung

v.link

v.link RL3-NBT2 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung

Curt Manufacturing

Curt Manufacturing A25 Bedienungsanleitung

v.link CI-RL4-MIB3-E Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken