Vaillant 0020180635 Benutzerhandbuch

en System installation instructions

cs Systém návod k instalaci

de System Installationsanleitung

fi Järjestelmän asennusohjeet

fr Notice d’installation du système

hr Upute za instaliranje sustava

nl Systeem installatiehandleiding

no Installasjonsveiledning for

system

sk Návod na inštaláciu systému

sl Navodila za namestitev sistema

sv System installationsanvisning

Heat pump system

0020180635

geoTHERM 3kW mono, gas-fired boiler, 2-zone

module, VRC 700, VR 91

Publisher/manufacturer

Vaillant GmbH

Berghauser Str. 40 D-42859 Remscheid

Tel. +49 21 91 18‑0Fax +49 21 91 18‑2810

[email protected] www.vaillant.de

en System installation instructions ........................ 1

cs Systém návod k instalaci...................................... 8

de System Installationsanleitung.......................... 15

fi Järjestelmän asennusohjeet ............................ 22

fr Notice d’installation du système...................... 29

hr Upute za instaliranje sustava ............................. 36

nl Systeem installatiehandleiding ........................ 43

no Installasjonsveiledning for system.................. 50

sk Návod na inštaláciu systému ............................. 57

sl Navodila za namestitev sistema......................... 64

sv System installationsanvisning ......................... 71

System 0020180635 1

0020251826_01 System installation instructions 1

System installation instructions

1 System 0020180635

VWS 36/4.1 230V with gas-fired boiler, 2-zone module, VRC 700 and VR 91

Caution.

Risk of material damage caused by incomplete installation.

This drawing is a basic representation and does not replace complete planning. This drawing does not

contain all of the required valves and safety fittings for a complete installation.

▶Observe the applicable national and international laws, standards and guidelines.

▶When planning, installing and subsequently operating this system, you must observe all the install-

ation and operating instructions available for the product, the relevant accessories and for any other

component.

▶The responsibility for design lies with the responsible company.

1.1 Basic hydraulic diagram 0020180635

1 Heat generator

2 Heat pump

3e Circulation pump

5 Monovalent domestic hot water cylinder

7i 2-zone module

8a Expansion relief valve

8b Potable water expansion relief valve

8c Safety group –drinking water connection

8e Heating diaphragm expansion vessel

8f Diaphragm expansion vessel –potable water

9a Single-room temperature control valve (thermo-

static/motorised)

9b Zone valve

9c Flow regulator valve

9d Bypass valve

9h Filling/draining cock

9j Tamper-proof capped valve

9k 3-port mixing valve

10c Non-return valve

12 System control

12a Remote control unit

2 Installation checklist

2System installation instructions 0020251826_01

12d Expansion/wiring centre

12g eBUS bus coupler

12k Limit thermostat

12m Outdoor temperature sensor

1.2 Wiring diagram 0020180635

1 Heat generator

2 Heat pump

3e Circulation pump

5 Monovalent domestic hot water cylinder

7i 2-zone module

9b Zone valve

9k 3-port mixing valve

12 System control

12a Remote control unit

12d Expansion/wiring centre

12g eBUS bus coupler

12k Limit thermostat

12m Outdoor temperature sensor

FS Flow temperature sensor/swimming pool sensor

2 Installation checklist

You must observe all the operating and installation instructions included with the system components.

Work Comments/settings

1 Comply with the conditions for the installation environment 1. Minimum volume of the installation room 1.60 m³

2. Environmental temperature 7 °C –40 °C

3. Frost-proof

4. Dry

2 Install the heat pump on a wall that has sufficient load-bearing capa-

city

Weight of the heat pump: 59 kg

3 Comply with the specified minimum clearances For free spaces for maintenance work, see the installa-

tion instructions for the relevant system components

4 Observe the position of the VRC 700 in the living room or main control room

5 Check the brine circuit for leak-tightness

Commissioning checklist 3

0020251826_01 System installation instructions 3

Work Comments/settings

6 Insulate the brine pipes in the house so that they are vapour-diffu-

sion-tight

Prevent condensation.

7 Use cold pipe clips to install the brine pipes in the house Prevent thermal bridges.

8 Use the correct brine fluid Monoethylene glycol, essential for fault-free operation.

9 Use the correct mixing ratio of monoethylene glycol to water 3:7, efficient operation only when the defined mixing ratio

is used

10 Use a refractometer to check the mixing ratio Efficient operation only when the defined mixing ratio is

used

11 Choke the output of the filling pump Reduce the penetration of air in the brine circuit.

12 Sufficiently dimension the gas-fired boiler's expansion vessel for the

heating circuit

No expansion vessel present in the heat pump.

13 Connect the heat pump via a separately fused plug socket Observe the connection conditions in accordance with

the data plate.

14 Use connection terminals when connecting multiple conductors Prevent communication faults.

15 Install a bus coupler in the VR 32 in the gas-fired boiler The gas-fired boiler is the second participant in the

eBUS.

17 Check all cable connections for tensile strength

16 Visually check all cable connections for damage

3 Commissioning checklist

3.1 VC 146/5-5, VC 206/5-5, VC 266/5-5

Work Comments/settings

1 Start the installation assistant If it is not started automatically

2Language Select

3Filling mode: 3-way valve is in mid-position Filling mode, fill the installation to at least 0.1 MPa (1.0

bar) via the return line

4Purge program: Select circ. using +/- Heating circuit the programme ends automatically

5Purge program: Select circ. using +/- DHW circuit the programme ends automatically

6Target flow temp. 75 °C, setting for the maximum target flow temperature

in heating mode

7DHW temperature 65 °C, setting for the maximum domestic hot water

temperature

8Comfort mode Off

9Heating partial load Auto

10 Auxiliary relay External pump, if present

11 Accessory relay 1 Circulation pump

12 Accessory relay 2 External pump, if present

13 Contact details Enter on the VRC 700

14 End the installation assistant? Yes

15 Menu →Installer level →Test programs →Check programs

16 P.01 and P.02 Check the gas connection pressure in accordance with

the installation instructions

17 P.01 and P.02 Check the CO₂content in accordance with the installa-

tion instructions

3 Commissioning checklist

4System installation instructions 0020251826_01

3.2 VWS 36/4.1 230V

Work Comments/settings

18 Start the installation assistant OK

19 Language Select

20 Freeze protection −10 °C

21 Purge environment and building circuit No

22 Purge building circuit No

23 Check program: Purge environment circuit Yes, test active, end after approx. 30 minutes

24 Contact details Enter on the VRC 700

25 End the installation assistant? Yes

26 Menu →Installer level →Test menu →Sensor/actuator test

27 T.82 Building circuit pressure Check, at least 1500-2000 mbar

28 T.101 Environment circuit pressure Check, at least 1500-2000 mbar

29 T.146 Outside temperature Check, actual temperature display

3.3 VRC 700

Work Comments/settings

30 Language Select

31 System diagram 7

32 Config.: VR70 addr. 1 1

33 System configuration OK

34 Fault status No fault present

35 Water pressure Check, at least 1500-2000 mbar

36 System status Display of current operating mode

37 Frost protect. delay 4 hours

38 OT constant heating 0 °C (min. -2 °C)

39 Control modules Display Display (VRC 700), heat pump 1 (VWS 36/4.1 230V),

heat generator 2 (VC ...), VR91, check of the eBUS con-

nections

40 Adaptive heat. curve No

41 Configure heat. circ. All

42 Automatic cooling No

Function can be activated for underfloor heating

43 Start OT cooling 21 °C/flexible

Depends on the end customer and the type of brine

source. For compact and flat collectors, you should not

use passive cooling

44 Source regeneration No

Observe legal requirements, which may depend on the

countries

45 Curr. room air hum. Current value display

46 Auxiliary heater type condens.

47 Buff. cyl. offs. 10 K

48 System diagram configuration

49 System diagram 7

50 Config.: VR70 addr. 1 1

Commissioning checklist 3

0020251826_01 System installation instructions 5

Work Comments/settings

51 MA VR70, addr. 1 No funct.

52 Heat pump 1

53 Status Current value display (standby, heating, cooling, do-

mestic hot water)

54 Current flow temp. Current value display

55 Heat generator 2

56 Status Current value display (standby, heating, cooling, do-

mestic hot water)

57 Current flow temp. Current value display

58 HEATING 1

59 Type of circuit Heating

60 Status Current value display (off, heating mode, cooling, do-

mestic hot water)

61 Target flow temp. Current value display

62 Max limit outs.temp. 21 °C, change in consultation with the customer, if re-

quired

63 Heating curve 0.4 to 0.6 for underfloor heating

64 Minimum temperature 15 °C

65 Maximum temperature 45 °C for underfloor heating

66 Auto Off mode Set-back

67 Cooling possible Yes for underfloor heating

No; you should not use passive cooling for compact col-

lectors and flat collectors

68 Dew point monitoring Yes

69 Min. cool. fl. tgt temp. 18 °C

70 End OT cooling 15 °C

71 Offset dew point 2 K

72 Pump status Current value display: off /On

73 HEATING 2

74 Type of circuit Heating

75 Status Current value display (off, heating mode, cooling, do-

mestic hot water)

76 Target flow temp. Current value display

77 Current temperature Current value display

78 Excessive temp.

79 Max limit outs.temp. 21 °C, change in consultation with the customer, if re-

quired

80 Heating curve –0.4 to 0.6 for underfloor heating

–max. 1.0 radiator heating

81 Minimum temperature 15 °C

82 Maximum temperature –45 °C for underfloor heating

–55 °C for radiator heating

83 Auto Off mode Set-back

84 Cooling possible No, with high-temperature heating circuit

85 Pump status Current value display: off /On

86 Mixer status Current value display: Opening,Closing,Stationary

87 ZONE1

88 Zone activated Current value display: No /Yes

89 Day temperature 20 °C

90 Set-back temp. 15 °C

91 Room temperature Current value display

92 Zone assignment VRC 700

3 Commissioning checklist

6System installation instructions 0020251826_01

Work Comments/settings

93 Zone valve status Current value display (closed/open)

94 ZONE2

95 Zone activated Current value display: No /Yes

96 Day temperature 20 °C

97 Set-back temp. 15 °C

98 Room temperature Current value display

99 Zone assignment VR91 ad.1

100 Zone valve status Current value display (closed/open)

101 Domestic hot water

102 Cylinder active Condition: Domestic hot water cylinder in the system

103 Target flow temp. Current value display

104 Domestic hot water 60 °C

Inform the end user about the anti-legionella function

105 Current cyl. temp. Current value display

106 Cyl. charging pump Current value display: off /On

107 Circulation pump Current value display: off /On

108 Anti-legionella day –Select: off,Monday,Tuesday,Wednesday,

Thursday,Friday,Saturday,Sunday,Monday -

Sunday

–Factory setting: off

109 Anti-legionella time 04:00

110 Cyl. boost hysteresis 5 K

111 Cylinder boost offset 25 K

112 Max. cyl. charg. time 45 min.

113 DHW req. anti-cy time 30 min.

114 Ch. pump overrun time 5 minutes

115 Parallel cyl. charging off

116 Menu →Installer level →Service information

117 Enter contact details Telephone number/company

118 Service date Next service on Maintenance interval: 1 year

→End user menu Implement the settings for the end user/inform the end

user

119 Menu →Basic settings →Enter zone name →ZONE1 →Change Enter a suitable name for the zone, e.g. Flat 1

(In consultation with the customer)

120 Menu →Basic settings →Enter zone name →ZONE2 →Change Enter a suitable name for the zone, e.g. Flat 2

(In consultation with the customer)

121 Menu →Desired temperatures →ZONE1 Zone1 (name after being renamed)

122 Day temp. heating 20 °C

123 Day temp. cooling 24 °C

124 Set-back temp. heat. 15 °C

125 Room temperature Current value display

126 Menu →Time programmes →ZONE1 Changed the time schedule for Zone 1 (name after being

renamed) following consultation with the customer

Zone 1 = heating circuit 1

127 HEATING 1: Cooling change following consultation with the customer

128 Domestic hot water change following consultation with the customer

129 Circulation change following consultation with the customer

Commissioning checklist 3

3.4 VR 91

Work Comments/settings

130 Basic settings

131 Language Select

132 Menu →Installer level →System configuration

133 Fault status No fault

134 Control modules Display of the control unit's software version

135 Remote control address 1, depending on the setting on the VRC 700: Zone as-

signment

136 Menu →Desired temperatures →ZONE2

137 Day temp. heating 20 °C

138 Set-back temp. heat. 15 °C

139 Menu →Time programmes →ZONE2

140 Heating change following consultation with the customer

141 Cooling change following consultation with the customer

1 Systém 0020180635

8Systém návod k instalaci 0020251826_01

Systém návod k instalaci

1 Systém 0020180635

VWS 36/4.1 230V s plynovým kotlem, dvouzónovým modulem, VRC 700 a VR 91

Pozor!

Riziko věcných škod způsobených neúplnou instalací!

Tento výkres je principiální zobrazení a nenahrazuje úplný plán. Tento výkres neobsahuje všechny

potřebné ventily a bezpečnostní armatury pro úplnou instalaci.

▶Dodržujte příslušné předpisy, normy a směrnice.

▶Při plánování a instalaci i pozdější obsluze bezpodmínečně dodržujte všechny návody k instalaci

a obsluze, které byly vytvořeny pro výrobek, dotyčné příslušenství nebo pro případnou jinou sou-

část.

▶Za provedení odpovídá příslušný podnikatel.

1.1 Schéma hydraulického systému 0020180635

1 Zdroj tepla

2 Tepelné čerpadlo

3e Cirkulační čerpadlo

5 Zásobník teplé vody monovalentní

7i 2zónový modul

8a Pojistný ventil

8b Pojistný ventil pitná voda

8c Bezpečnostní skupina - přípoj pitné vody

8e Membránová expanzní nádoba topení

8f Membránová expanzní nádoba pitné vody

9a Ventil regulace samostatné místnosti (termosta-

tický/motorický)

9b Ventil zóny

9c Ventil k regulaci větvě

9d Přepouštěcí ventil

9h Napouštěcí a vypouštěcí ventil

9j Ventil s krytkou

9k 3cestný směšovač

10c Zpětný ventil

12 Systémový regulátor

12a Zařízení dálkového ovládání

Inhaltsverzeichnis

Sprachen:

Andere Vaillant Wärmepumpe Handbücher

Vaillant

Vaillant VWL 35/5 AS 230V S2 Bedienungsanleitung

Vaillant

Vaillant AROTHERM VWL ../2 A series Bedienungsanleitung

Vaillant

Vaillant aroTHERM VWL 55/3 A 230 V Bedienungsanleitung

Vaillant

Vaillant uniTOWER plus Bedienungsanleitung

Vaillant

Vaillant aroTHERM VWL Series Bedienungsanleitung

Vaillant

Vaillant geoTHERM VWS Bedienungsanleitung

Vaillant

Vaillant climaVAIR VAI 2-025 WN Bedienungsanleitung

Vaillant

Vaillant geoTHERM VWS Series Bedienungsanleitung

Vaillant

Vaillant flexoTHERM exclusive VWF 57/4 Bedienungsanleitung

Vaillant

Vaillant 0020235577 Benutzerhandbuch

Vaillant

Vaillant aroSTOR VWL BM 270/5 Bedienungsanleitung

Vaillant

Vaillant aroTHERM VWL 85/2 Bedienungsanleitung

Vaillant

Vaillant aroTHERM plus Bedienungsanleitung

Vaillant

Vaillant aroSTOR VWL B 270/5 Bedienungsanleitung

Vaillant

Vaillant aroTHERM VWL 55/3 A 230 V Bedienungsanleitung

Vaillant

Vaillant VWZ MEH 97/6 Bedienungsanleitung

Vaillant

Vaillant flexoTHERM exclusive VWF 117/4 Bedienungsanleitung

Vaillant

Vaillant aroCOLLECT VWL 11/4 SA Bedienungsanleitung

Vaillant

Vaillant geoTHERM SERIES Bedienungsanleitung

Vaillant

Vaillant geoTHERM VWS Bedienungsanleitung

Vaillant

Vaillant geoTHERM VWS Bedienungsanleitung

Vaillant

Vaillant aroSTOR VWL B 200/5 UK Bedienungsanleitung

Vaillant

Vaillant VWZ MPS 40 Bedienungsanleitung

Vaillant

Vaillant aroTHERM plus VWL 35/6 A 230V S2 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung