Vanco EVEXFBRK1 Bedienungsanleitung

Vanco Part Number

EVEXFBRK1

HDMI® Extender over

Fiber with KVM USB

Pass-through

www.vanco1.com • 800.626.6445

HDMI® EXTENDER

over Fiber with KVM USB Pass-through

www.vanco1.com 800.626.6445

1. Do not expose this unit to water, moisture, or

excessive humidity.

2. Do not install or place this unit in a built-in

cabinet, or other conned space without

adequate ventilation.

3. To prevent risk of electrical shock or re

hazard, due to overheating do not obstruct

unit’s ventilation openings.

4. Do not install near any source of heat,

including other units that may produce heat.

5. Do not place unit near ames.

6. Only clean unit with a dry cloth.

7. Unplug unit during lightening storms or when

not used for an extended period of time. A

surge protector is strongly recommended.

8. Protect the power cord from being walked on

or pinched, particularly at the plugs.

9. Use unit only with accessories specied by

the manufacturer.

10. Refer all servicing to qualied personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same

video resolution and audio settings on all electronic equipment in the system. When there are multiple

sources and displays, the video resolution and audio setting on all connected units must be adjusted

to correspond with that of the display having the lowest video and audio capability.

WARNING

DEAR CUSTOMER

Thank you for purchasing this product.

For optimum performance and safety, please

read these instructions carefully before connecting, operating or

adjusting this product. Please keep this manual for future reference.

This product is 100% inspected and tested in the United States to verify

HDMI performance parameters.

www.vanco1.com 800.626.6445 3

INTRODUCTION

The Evolution by Vanco EVEXFBRK1 HDMI Extender with KVM, bi-directional IR, and RS-232, extends 4K HDR video and

audio signals up to 984ft/300M over multi-mode ber optic cables, and 6.2mi/10km over single mode ber optic cables

and modules! USB 2.0 KVM allows for controlling a security NVR/DVR, computer, NAS system, or any other component

that is controlled by USB with this extender. No need to run a separate line or extender just for KVM control! Bi-directional

IR pass-through allows for source and/or display control. Also features RS-232 pass-through for additional control. For

extending HDMI with 4K HDR resolution at an extreme distance, the EVEXFBRK1 is a great solution for any application.

The EVEXFBRK1 includes two units: transmitting unit (EVEXFBRK1-TX) and receiving unit (EVEXFBRK1-RX). The

transmitting unit is used to capture the HDMI input with control signals and carries the signals via ber optic cables. The

receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals. Both units require

power.

FEATURES

• Transmits audio and video via HDMI as well as complete KVM (Keyboard, Video, Mouse) functionality via

USB 2.0 ports over ber optic cables

• Transmission range: 984ft/300m over multi-mode ber optic cables; 6.2mi/10km over single mode ber

optic cables

• Supports 4K@60Hz, 4:2:0 chroma sampling and HDR; 4K@60Hz and 4:4:4 chroma sampling

• Supports HDR10 and Dolby Vision

• USB 2.0 pass-through

• Includes (2) USB ports on receiving end for keyboard/mouse connectivity

• Features bi-directional IR (20kHz to 60kHz) pass-through for source and/or display control

• RS-232 pass-through

• Supports HDCP2.2

• Multi-mode SFP modules included

• Dimensions: 4.9” W x 4.4” H x 1.1” D

HDMI® Extender over Fiber with KVM USB Pass-through

Part # EVEXFBRK1

PACKAGE CONTENTS

• EVEXFBRK1 (TX & RX)

• (1) IR Transmitter

• (1) IR Receiver

• (2) DC 12V Power Supply

• (1) USB 2.0 Male A Male-to-Male Cable

• (2) Multi-mode SFP Modules

• Product Manual

www.vanco1.com 800.626.6445

SPECIFICATIONS

HDMI Compliance ...................................................... HDMI 2.0a

HDCP Compliance ..................................................... HDCP 2.2

Video Bandwidth ........................................................ Single-link 594MHz [18Gbps]

Video Support ........................................................... HDR 4K@60Hz (4:2:0 10-bit color) / 4K@60Hz

(4:4:4 8-bit color)

HDMI over UTP.......................................................... Yes

Audio Support ........................................................... Surround sound [up to 7.1ch) or stereo digital audio

Input TMDS Signal .................................................... 1.2 Volts [peak-to-peak]

Input DDC Signal ....................................................... 5 Volts [peak-to-peak, TTL]

ESD Protection .......................................................... Human body model — ±15kV [air-gap discharge] &

±8kV [contact discharge]

PCB Stack-up ............................................................ 4-layer board [impedance control — differential

100Ω; single 50Ω]

IR Pass-thru.............................................................. Bi-directional

RS-232 Support ........................................................ Yes

HDMI Source Control ............................................... Controllable via IR pass-through from RX to TX with

IR extenders

HDMI Connector ........................................................ Type A [19-pin female]

3.5mm Connector...................................................... IR receiver / IR blaster

Operation Temperature............................................... 0~40°C [32~104°F]

Storage Temperature ................................................. -20~60°C [-4~140°F]

Relative Humidity....................................................... 20~90% RH [no condensation]

Power Supply ............................................................ 12V, 2A

Power Consumption ................................................... Max 10W

www.vanco1.com 800.626.6445 5

1. USB 2.0 Type A Port: Connect the included male to male USB 2.0 cable to the source for KVM control

2. RS-232: Connect for control via PC or third party control system

3. Firmware Update Port: Any available f/w updates will be available under the EVEXFBRK1 product page on

www.vanco1.com

4. DIP Switch for Control Type Pass-through: See “Control Type” section below; important to note that this

extender will only pass USB signals OR IR/RS-232, not all simultaneously

5. Power and Link Lights: Both LEDs should be illuminated for proper functionality, link indicates that both the

TX and RX are communicating

6. SFP OUT: Connect ber optical cables from this unit to the RX

7. HDMI IN: Connect an HDMI source

8. IR IN: Connect the included IR Receiver (RX) to control the display

9. IR OUT: Connect the included IR Transmitter (TX) to control the source

10. DC 12V: Connect the included 12V Power Supply (both TX and RX need to be plugged into power)

PANEL DESCRIPTIONS

Transmitting Unit

21 345 6

78 9 10

www.vanco1.com 800.626.6445

PANEL DESCRIPTIONS

Receiving Unit

1345

789

1. (2) USB 2.0 Type A Ports: Connect male to male USB 2.0 cable(s) to a keyboard and/or mouse for KVM

control; wireless keyboard and mouse can be used, however it must follow the manufacturers’ wireless

range from this unit

2. RS-232: Connect for control via PC or third party control system

3. Firmware Update Port: Any available f/w updates will be available under the EVEXFBRK1 product page on

www.vanco1.com

4. DIP Switch for Control Type Pass-through: See “Control Type” section below; important to note that this

extender will only pass USB signals OR IR/RS-232, not all simultaneously

5. Power and Link Lights: Both LEDs should be illuminated for proper functionality, link indicates that both

the TX and RX are communicating

6. SFP IN: Connect ber optical cables from this unit to the TX

7. HDMI OUT: Connect an HDMI display

8. IR IN: Connect the included IR Receiver (RX) to control the source

9. IR OUT: Connect the included IR Transmitter (TX) to control the display

10. DC 12V: Connect the included 12V Power Supply (both TX and RX need to be plugged into power)

www.vanco1.com 800.626.6445 7

Passing through USB or IR/RS-232 Signals

CONTROL TYPE SET UP

While the EVEXFBRK1 can pass-through USB 2.0, bi-directional IR, and RS-232, it cannot do all three signals

simultaneously. If USB is activated, bi-directional IR and RS-232 pass-through will be inactive, and vice versa.

See the below table (PIN #2). The dip switches allow for rmware updates (PIN #1) and to either activate or

de-activate IR as well (PIN #3).

See below for dip switch settings, note that DOWN is ON and both TX and RX need to be set to

the same dip switch settings.

DIP Switch Position

Description

TX & RX

PIN #1

ON For system rmware update

OFF Default and normal setting

PIN #2

ON USB Function ON

OFF RS-232/IR function ON

PIN #3

ON Disable IR function

OFF Enable IR function

www.vanco1.com 800.626.6445

CONNECT AND OPERATE

1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc.

to the HDMI input on the Transmitting unit

2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit

3. Connect ber optical cables with modules and insert into the output of the Transmitting unit, and the other

end to the SFP input of the Receiving unit

4. For power, plug in both the Transmitting unit and Receiving unit with the included power supplies

5. Power on each device in the same sequence

6. Optional: Connect the single mode modules for longer distance ber optical cable run (not included)

At this point the display connected should display the source signal connected to the extender set. If no signal

is being displayed, connect a ber optical cable to rule out cabling. If a display is having difculty receiving a

signal, access the display’s menu and adjust the resolution (lowest to highest until signal is displayed). A 24

Hz vertical refresh rate may work better than 60 Hz or higher. Use the source remote at the receiver emitter

to test IR functionality. If the IR remote function is not responding, check the emitters to ensure they are

placed correctly and are plugged into the correct IR jacks on the Extender set receiving and transmitting units.

CONNECTION DIAGRAM

IR Transmitter

Source

HDTV

ansmitter

Receiv

HDMI HDMI

IR Receiver

IR Transmitter

IR Receiver

Fiber Cable

USB

Keyboard and Mouse

Computer

www.vanco1.com 800.626.6445 9

IR PASS-THRU

IR PASS-THROUGH

The bi-directional IR system allows you to control the source that is connected to the extender unit, from

the display; or the display from the source, not simultaneously. There are two important things to note when

setting up the IR system:

1. The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed

at the display for controlling the source; or at the source for controlling the display.

2. The IR Blaster (IR TX) is what sends the IR signal to what you are intending to control, whether it’s the

source or the display. This pigtail is placed at the source; either pointed at the source, or placed on the

front panel of the source, see below for placement tips. Or placed at the display to control the display

from the source.

3. Use only the IR accessories that are incnluded with this extender, using third party IR blasters and/or

receivers may not work

IR Receiver IR Blaster

IR Blaster (TX)

• To control the source: Plug IR Blaster into IR Blaster Port of transmitter unit (EVEXFBRK1-TX); place

blaster in front of the IR eye of the source

• To control the display: Plug IR Blaster into IR Receiver Port of receiver unit (EVEXFBRK1-RX); place

blaster in front of the IR eye of the display

Note: Placement of the IR Blaster is important and can result in the IR system not working if improperly

placed.

• First, locate the IR eye or window on the source

• If placing the IR Blaster right on the front panel of the source, do not stick right on top of the IR eye or

IR window. The IR signal cannot travel through the double-sided tape on the blaster. Instead place the

blaster on either side, or on the top or bottom of the IR eye or window, with the tip of the blaster facing

the IR eye or window. See below for illustration of where IR signal shoots from on IR Blaster:

www.vanco1.com 800.626.6445

IR RECEIVER (RX)

• To control the source: Plug IR Receiver into IR RX port of receiver unit (EVEXFBRK1-RX); place receiver

at or near display

• To control the display: Plug IR Receiver into IR RX port of transmitter unit (EVEXFBRK1-TX); place

receiver in position where it is able to receive remote signals

Inhaltsverzeichnis

Andere Vanco Extender Handbücher

Vanco

Vanco Evolution EVEX2005 Bedienungsanleitung

Vanco

Vanco Evolution EVEXKVM1 Bedienungsanleitung

Vanco

Vanco EVEX2006 Bedienungsanleitung

Vanco

Vanco Evolution EVEXKVM3 Bedienungsanleitung

Vanco

Vanco EVEXHDB2 Bedienungsanleitung

Vanco

Vanco Evolution EVEX4K50 Bedienungsanleitung

Vanco

Vanco HDWIRKIT Bedienungsanleitung

Vanco

Vanco 280332 Bedienungsanleitung

Vanco

Vanco 280547 Bedienungsanleitung

Vanco

Vanco EVEXHDARC Bedienungsanleitung

Vanco

Vanco 280567 Bedienungsanleitung

Vanco

Vanco VPW-280572 Bedienungsanleitung

Vanco

Vanco Evolution EVWP2006 Bedienungsanleitung

Vanco

Vanco Evolution EVEXWHDMI Bedienungsanleitung

Vanco

Vanco 280544 Bedienungsanleitung

Vanco

Vanco Evolution EV4KWHDMI Bedienungsanleitung

Vanco

Vanco EVEX2003 Bedienungsanleitung

Vanco

Vanco VPW-280577 Bedienungsanleitung

Vanco

Vanco 280502 Bedienungsanleitung

Vanco

Vanco Evolution EVMX44VW Bedienungsanleitung

Vanco

Vanco 280501 Bedienungsanleitung

Vanco

Vanco EVOLUTION EVEXARC1 Bedienungsanleitung

Vanco

Vanco HDMIEX50 Bedienungsanleitung

Vanco

Vanco EVOLUTION EVEXUSB2 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung