Vanco Evolution EVEX2005 Bedienungsanleitung

HDMI

Transmitter

Connect Power Supply

QUICK INSTALL GUIDE

Factory Setting EDID & EQ Dial - From Factory Settings are as Follows:

1. Transmitter Factory Default Setting is Set at EDID = “0” Supporting: HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60)(720p@60) - 24bit 2D video & 7.1ch audio

2. Receiver E.Q. Dial Setting = “4” Supporting: 20M-25Meters (66 ft to 82 ft)

3. Proceed to Connect & Operate with Normal Installation (see reverse side). If there is no handshake or signal, Adjust EQ

Gain Control according to your CAT5e/CAT6 Cabling: from Minimum Dial Setting “0” to Maximum Setting “7”

Manual EDID Learning Mode

1. Set Learning (Copy) EDID Mode on the Transmitter (TX) unit = “7”

2. (SEE DRAWING) FIRST: Connect Transmitter (TX) unit directly to the Flat Panel Display using a HDMI cable. SECOND:

Connect the 5VDC Power Adapter. The “yellow” Status LED light must blink once for Learning (Copy) EDID to be

Successful. Now you can disconnect Transmitter (TX) from Flat Panel Display.

Note - Do not connect Receiver ( RX) unit during Learning (Copy) EDID Mode

If experiencing No Picture, Picture Flashing, or Drop-Signal then proceed to Manual Learning EDID Mode

NOTE - Recommended EDID setting for most cable and satellite set top boxes is

EDID “4” or “5”. If no signal is displayed after manual EDID learning mode, adjust

to another EDID setting by doing the following:

1. Unplug the 5VDC power supply and HDMI cable from the Transmitter (TX)

2. Adjust EDID to desired setting

3. Reconnect HDMI cable from the source into the Transmitter (TX)

4. Reconnect 5VDC power supply to the Transmitter (TX)

3. Change Transmitter back to Factory Default Setting EDID = “0”

4. Proceed to Connect & Operate with Normal Installation (see reverse side). Wait for Sync

Lights (on Transmitter & Receiver) to Stop Flashing

5. If no Picture or Signal is on the Flat Panel Display then Power OFF (both Units) & Power

ON (both Units). Simply remove the 5VDC Power supplies & reconnect

BluRay® Player

HDTV

HDMI HDMI

IR Transmitter IR Receiver

IR Transmitter

Receiver

HDMI over Cat5e/6

Transmitter Receiver

Back

Front

Back

Front

1. Connect a source such as a Blu-Ray Player, game

console, A/V Receiver, Cable or Satellite Receiver, etc.

to the HDMI input on the Transmitting unit.

2. Connect a display such as an HDTV or HD Projector to

the HDMI output on the Receiving unit.

3. Connect a single Category 5e/6 up to 131ft/40m to

the output of the Transmitting unit, and the other end to

the input of the Receiving unit.

4. For power, plug both the Transmitting unit and Receiving

unit with the included power supplies.

CONNECT AND OPERATE

0 - EDID Full-HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60 (720p@60) - 24bit 2D video & 7.1ch audio

1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio

2 - EDID Full-HD(1080p@60) - 24bit 3D video & 7.1ch audio

3 - EDID Full-HD(1080p@60) - 24bit 3D video & 2ch audio

4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 7.1ch audio

5 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 2ch audio

6 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio

7 - Auto EDID learning/ Manual EDID learning mode

EQ ROTARY DIAL

If you see ickering or blinking image on the display, adjust the EQ rotary

switch to improve the cable skew. MAX stands for the strongest HDMI

signal level for the longest possible transmission length while MIN stands

for the weakest HDMI signal level for short transmission length. Adjust the

signal level from MIN to MAX until desired video quality is displayed.

Recommended EQ settings

LENGTH

Position Cable Length

0 (MIN)-2 under 15m (49.5ft)

3-5 15-30m (49.5 ft - 99ft)

6-7 (MAX) 30-40m (99ft - 132ft)

EDID SETTINGS

Andere Handbücher für Evolution EVEX2005

Inhaltsverzeichnis

Andere Vanco Extender Handbücher

Vanco

Vanco Evolution EV4KWHDMI Bedienungsanleitung

Vanco

Vanco HDEX60 Bedienungsanleitung

Vanco

Vanco Evolution EVEXWHDMI Bedienungsanleitung

Vanco

Vanco EVOLUTION EVWP3000 Bedienungsanleitung

Vanco

Vanco Evolution EVEXHDB1 Bedienungsanleitung

Vanco

Vanco HD4KEX30 Bedienungsanleitung

Vanco

Vanco EVEX2006 Bedienungsanleitung

Vanco

Vanco EVOLUTION EVEXUSB2 Bedienungsanleitung

Vanco

Vanco Evolution EVEX4K50 Bedienungsanleitung

Vanco

Vanco 280502 Bedienungsanleitung

Vanco

Vanco Evolution EVEXHDB3 Bedienungsanleitung

Vanco

Vanco EVEXHDARC Bedienungsanleitung

Vanco

Vanco 280547 Bedienungsanleitung

Vanco

Vanco Evolution EVEXKVM3 Bedienungsanleitung

Vanco

Vanco HDMIEX50 Bedienungsanleitung

Vanco

Vanco Evolution EVEX4K70 Bedienungsanleitung

Vanco

Vanco HDWIRKIT Bedienungsanleitung

Vanco

Vanco PulseAudio PAEXARC1 Bedienungsanleitung

Vanco

Vanco Evolution Bedienungsanleitung

Vanco

Vanco 280567 Bedienungsanleitung

Vanco

Vanco Evolution EVEXKVM1 Bedienungsanleitung

Vanco

Vanco Evolution EVMX44VW Bedienungsanleitung

Vanco

Vanco HDEX60 Bedienungsanleitung

Vanco

Vanco EVEX2003 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung