Vanco Evolution EVMX4008 Bedienungsanleitung
Vanco Part Number
EVMX4008
HDBaseT 8x8 Matrix
Selector Switch
(230ft/70m)
www.vanco1.com • 800.626.6445
HDBaseT™ 8x8
MATRIX SELECTOR SWITCH
(230ft/70m)
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water,
moisture, or excessive humidity.
2. Do not install or place this unit
in a built-in cabinet, or other
conned space without adequate
ventilation.
3. To prevent risk of electrical shock
or re hazard, due to overheating
do not obstruct unit’s ventilation
openings.
4. Do not install near any source of
heat, including other units that
may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening
storms or when not used for
an extended period of time.
A surge protector is strongly
recommended.
8. Protect the power cord from
being walked on or pinched,
particularly at the plugs.
9. Use unit only with accessories
specied by the manufacturer.
10. Refer all servicing to qualied
personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal
and the same video resolution and audio settings on all electronic equipment in the
system. When there are multiple sources and displays, the video resolution and
audio setting on all connected units must be adjusted to correspond with that of the
display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting,
operating or adjusting this product. Please keep this
manual for future reference.
This product is 100% inspected and tested in the United
States to verify HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The Evolution by Vanco EVMX4008 8X8 Matrix with HDBaseT Technology, Wide-band IR, and PoE is
an HD switching and extension system that comprises of an 8 input/8 output matrix unit. Have 8
sources displayed simultaneously on any display or have a single source duplicated on multiple displays,
exibility for the perfect solution. Features HDBaseT (70m/230ft) technology, which allows for audio,
1080p video, IR, and Power over Cable to be transferred over a single Cat5e/6/7 cable up to 230
feet. Also features Power over Ethernet (PoE) Technology which transmits power over Cat5e/6, allowing
for Receiver unit to be powered without the use of a power supply. The result is an easy and plug and
play solution that allows each output with the ability to extend HDMI over long distances in conjunction
with the Evolution by Vanco HDBaseT (70m/230ft) receiver EVRX3000 (sold separately). Features
additional HDMI output per HDBaseT output for exibility or mirroring capability, able to handle up to 16
displays. With an output bandwidth of 6.75 Gbps, the EVMX4008 is capable of high denition video and
multi-channel audio distribution with simple control using the front panel or remotely via IR Receivers at
display locations. Includes RS-232 connectivity for third party integration for control and switching, as
well as IP control along with LAN connectivity for control and switching remotely, using a smartphone or
tablet. Also features EDID management system, which allows and encourages device communication
compatibility for seamless integration. For longer length applications with full exibility for control, the
EVMX4008 is a great solution.
FEATURES
www.vanco1.com 800.626.6445
4
HDBaseT 8x8 Matrix Selector Switch (230ft/70m)
Part # EVMX4008
• Allows up to 8 HDMI sources to be distributed simultaneously to up to 8 displays
• 8 additional HDMI outputs for exibility or mirroring capability; allows for connection of
up to 16 displays or the ability to create a larger distribution system by cascading or
daisy chaining
• HDBaseT Technology that supports HDMI Deep Color, 3D, and up to 1080p High
Denition resolution
• Supports Power Over Ethernet (PoE) which integrates power into the Cat5e/Cat6
cable, requiring no power supply for receiving unit
• Transmission Range: Extends 1080p resolutions up to 230ft (70m)
• Features EDID management which supports default HDMI EDID and has the ability to
learn the EDID of display equipment for any “handshake” issues via RS-232 connectivity
• Receivers (sold separately) feature LED indicators for clear power and video signal
selection
• HDCP Compliant
• Supports HDMI Deep Color and 3D
• Supports 7.1 channel digital audio
• Wideband IR pass-through (20kHz to 60 kHz)
• Choose from 5 switching modes – front panel buttons, Local remote control, RS-232
control, IR call-back (dedicated IR extension cable connected to IR extension port, and
IR emitters on sources required), and IP control utilizing smartphone or tablet via LAN
• 24V 8.3A DC, UL Listed Power supply for 8X8 matrix
• 8X8 Matrix Dimensions: 17.26” (438.4 mm) W x 3.4” (86.4 mm) H x 12.56” (318.9
mm) D
www.vanco1.com 800.626.6445 5
SPECIFICATIONS
TECHNICAL SPECS
HDCP Compliance...................................................... Yes
Video Bandwidth ........................................................ Single-link 340Mhz [10.2 Gbps]
Video Support ........................................................... 480i/480p/720p/1080i/1080p @60 36-bit color
Audio Support ........................................................... Surround Sound (up to 7.1 ch) or stereo digital audio
ESD Protection .......................................................... [1] Human body model — ±19kV [air-gap discharge]
& ±12kV [contact discharge] [2] Core chipset — ±8kV
PCB stack-up ............................................................ 4-layer board [impedance control — differential
100Ω; single 50Ω]
Input ........................................................................ 8x HDMI / 1x RS-232 / 1x RJ-45 for IP Control / 9x
IR for IR receivers
Output...................................................................... 8x RJ-45 (HDBaseT) / 8x HDMI / 9x IR for IR
blasters
HDMI connector ........................................................ Type A 19 pin female
RJ-45 connector........................................................ WE/SS 8P8C with 2 LED indicators
RS-232 connector ..................................................... DE-9 [9-pin D-sub female]
3.5mm connector ...................................................... Earphone jack for IR blaster; [All IR Out] IR signal
from all outputs; [IR1~IR8] IR control on individual source device; Earphone jack for IR receiver; [System IR]
Receives IR commands from remote control; [IR1~IR8] Receives IR commands from individual remote control
MECHANICAL SPECS
Housing .................................................................... Metal enclosure
Power supply............................................................. 24V 8.3A DC
Power consumption.................................................... 120 Watts [max]
Operation temperature............................................... 32-104 degrees F
Storage temperature.................................................. -4 - 140 degrees F
Relative humidity ....................................................... 20-90% RH (no condensation)
PACKAGE CONTENTS
• (1) EVMX4008 HDBaseT 8X8 Matrix Selector Switch
• (9) IR Receiver (RX)
• (8) IR Blaster (TX)
• (1) DC 24V 8.3A power supply
• (1) Rack-mounting ear set
• (1) Installation software CD
• (1) IR remote control
• (1) User Manual
www.vanco1.com 800.626.6445
6
1. Power Switch
2. Source Status: Input source indicator LED
3. 7-segment LED: for output 1-8 status
4. IR SENSOR: IR sensor for receiving the IR commands from IR remote
5. Push Button: Select the output and input
6. Push Button: Enter Button
7. RS-232: RS-232 control port
8. +24V DC: 24V DC power jack
9. Ethernet: Ethernet control port
10. IR Receiver 1-8: Infrared 3.5mm socket for plugging in the extension cable of IR
receiver
11. LED Link
12. Output Port 1-8: RJ-45 outputs for each output channel
13. HDMI Local Loopout Port 1-8: Local loopout HDMI outputs for each output channel
14. IR Blaster 1-8: 3.5mm IR blaster socket for individual HDMI source control
15. System IR Receiver: Ext. IR receiver
16. All IR Output: 3.5mm IR blaster socket for HDMI source control on all 8 inputs
17. INPUT 1-8: HDMI inputs
PANEL DESCRIPTIONS
1
2
34
56
7
9
10
11
13
8
12
10
13
11
12
14
17
15
16
www.vanco1.com 800.626.6445 7
1 2 3 4 5 6
7 8
PANEL DESCRIPTIONS RECEIVER -
Part#EVRX3000 (Sold Separately)
1. 24V DC: Connect to 24V DC power supply (optional)
2. LED: Power indicator
3. HDMI OUT: Connects to an HDMI display with an HDMI male-male cable
4. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
5. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
6. Mini-USB: For rmware updates
7. LED: TX/RX link indicator
8. RJ-45: Plug in for Cat5e or Cat6 Cable
www.vanco1.com 800.626.6445
8
1. Full-HD(1080p@60)-24bit 2D & 2ch & Dolby 5.1ch
2. Full-HD(1080p@60)-24bit 2D & 7.1ch
3. Full-HD(1080p@60)-24bit 3D & 2ch
4. Full-HD(1080p@60)-24bit 3D & 7.1ch
5. HD(1080i@60)(720p@60)-24bit 2D & 2ch
6. HD(1080i@60)(720p@60)-24bit 2D & 7.1ch
7. Full-HD(1080p@60)-36bit 2D & 2ch
8. Full-HD(1080p@60)-36bit 2D & 7.1ch
9. Full-HD(1080p@60)-24bit 2D & 2ch
EDID
EDID Settings:
There are nine embedded default EDID settings as shown below:
EDID
EDID management allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the
display and source.
The EDID learning function is only necessary whenever any display on the HDMI output port is not outputting
audio and video properly. Because the HDMI source devices and displays may have various level of capability in
playing audio and video, the general principle is that the source device will output the lowest standards in audio
format and video resolutions to be acceptable among all HDMI displays connected. In this case, a 720p stereo
HDMI signal output would be probably the safest choice. The EDID function can also force the matrix to learn
the EDID of the lowest capable HDMI display among others to make sure all displays are capable to play the
HDMI signals normally.
There are 3 methods for EDID Learning as shown below:
1. IR Remote Control: Please refer to the Operation Control - IR Remote Control
2. Software Control: Please refer to the Operation Control - Software Control through RS-232 and LAN port
3. Web Interface Control: Please refer to the Operation Control – Web Interface Control
www.vanco1.com 800.626.6445 9
OPERATION CONTROL - FRONT
PANEL
1. INPUT/OUTPUT MAPPING
• Use the “LEFT” or “RIGHT“ push button to select the output desired to switch sources
to.
• Use the “UP” or “DOWN“ push button to select the specic source.
• Press “SET” to conrm
www.vanco1.com 800.626.6445
10
OPERATION CONTROL - IR
REMOTE CONTROL
1. INPUT/OUTPUT Switch - Push the corresponding button on the remote to select Input & Output port.
2. Function Key
Button Function
OFF Standby mode
ON Power on the matrix switcher
MUTE Turn off output’s video and audio
STATUS Preset output status
SAVE Save current mapping mode
PRESET Preset mapping mode
DEFAULT EDID Begin default EDID selection
LEARN EDID Begin EDID learning from one output
CLEAR Clear the previous IR operation procedure
TAKE Trigger the previous setting
F1 Reserved
F2 Reserved
Operation Procedure 7-Segment LED
IN/OUT Switch Output Number (1~8) + Input Number (1~8)
Ex: Input 2 To Output 3 1. Press output number key “3” to select Output 3
2. Press input number key “2” twice to select Input 2
3
-
3
2
Inhaltsverzeichnis
Andere Vanco Matrix-Umschalter Handbücher
Vanco
Vanco Evolution EVMX4K42 Bedienungsanleitung
Vanco
Vanco 280564 Montageanleitung
Vanco
Vanco EVOLUTION EVMX42MV Bedienungsanleitung
Vanco
Vanco 4x3 HDBaseT Montageanleitung
Vanco
Vanco VPW-280781 Bedienungsanleitung
Vanco
Vanco Evolution EVMX4044 Gebrauchsanweisung
Vanco
Vanco HDBaseT Lite Bedienungsanleitung
Vanco
Vanco VPW-280799 Bedienungsanleitung
Vanco
Vanco Evolution EVMX4K44 Bedienungsanleitung
Vanco
Vanco 281442 Bedienungsanleitung
Vanco
Vanco 280568 Bedienungsanleitung
Vanco
Vanco Evolution EVMX44SL Bedienungsanleitung
Vanco
Vanco VPW-280795 Bedienungsanleitung
Vanco
Vanco Evolution EVMX4K16 Bedienungsanleitung
Vanco
Vanco EVMX4X3 Bedienungsanleitung
Vanco
Vanco 280719 Bedienungsanleitung
Vanco
Vanco Evolution EVMX4442 Bedienungsanleitung
Vanco
Vanco Evolution EVMX4K08 Bedienungsanleitung
Vanco
Vanco 280688 Bedienungsanleitung
