Vanguard Instruments Auto-Ohm 10 Bedienungsanleitung

Auto-Ohm 10

Low Resistance Micro-Ohmmeter

USER’S MANUAL

Vanguard Instruments Company, Inc.

1520 S. Hellman Ave.

Ontario, California 91761, USA

TEL: (909) 923-9390

FAX: (909) 923-9391

May 16, 2017

Revision 1.0

Auto-Ohm 10 USER’S MANUAL REV 1.0

SAFETY SUMMARY

FOLLOW EXACT OPERATING PROCEDURES

Any deviation from the procedures described in this user’s manual may create one or more safety hazards,

damage the Auto-Ohm 10, or cause errors in the test results. Vanguard Instruments Co., Inc. assumes no liability

for unsafe or improper use of the Auto-Ohm 10. The following safety precautions must be observed during all

phases of test setup, test hookups, testing, and test lead disconnection.

SAFETY WARNINGS AND CAUTIONS

The Auto-Ohm 10 shall be used only by trained operators. All circuit breakers under test shall be off-line and fully

isolated.

SERVICE AND REPAIR

• Do not install substitute parts or perform any unauthorized modification to any Auto-Ohm 10 test unit.

• Repairs must be performed only by Vanguard Instruments Company factory personnel or by an authorized

repair service provider. Unauthorized modifications can cause safety hazards and will void the manufacturer’s

warranty.

EQUIPMENT RATINGS

IP Rating: The enclosure for the Auto-Ohm 10 has an IP rating of 67.

Pollution Degree: The Auto-Ohm 10 has a pollution rating of 2.

Operating Voltage: The Auto-Ohm 10 is rated for use with an operating voltage of 120V or 240V, auto-ranging

±10% of selected voltage.

Power Cord: The Auto-Ohm 10 is supplied with a 16 AWG, 16A power cord with a NEMA 5-15P plug. Replacement

cable shall have the same or better rating and is available through the manufacturer.

VENTILATION REQUIREMENTS

The Auto-Ohm 10 must be operated with the enclosure lid open.

SAFETY SYMBOLS

Indicates that caution should be exercised

CLEANING

To clean the Auto-Ohm 10:

• Disconnect all cables and turn the unit off.

• Use a soft, lint-free cloth to wipe all surfaces clean.

• Avoid getting moisture in openings and connectors.

• Don't use any cleaning products or compressed air.

REV 1.0 Auto-Ohm 10 USER’S MANUAL

TABLE OF CONTENTS

CONVENTIONS USED IN THIS DOCUMENT ....................................................................... 1

1.0 INTRODUCTION .................................................................................................................... 2

1.1 Product Overview ............................................................................................................ 2

1.2 Technical Specifications ................................................................................................... 5

1.3 Auto-Ohm 10 Controls and Indicators ............................................................................. 6

1.4 PRE-TEST SETUP ................................................................................................................... 7

1.4.1. Operating Voltages ................................................................................................... 7

1.4.2. Installing the Battery Fuse ........................................................................................ 7

1.4.3. Replacement Rechargeable Batteries ...................................................................... 8

1.4.4. Charging and Turning the Unit On and Off .............................................................. 8

1.4.5. Adjusting LCD Screen Contrast ................................................................................. 9

1.4.6. Configuring Power Saving Options ......................................................................... 10

1.4.7. Viewing Previous Test Results ................................................................................ 13

2.0 OPERATING PROCEDURES ................................................................................................. 14

2.1 Connection Diagram ...................................................................................................... 14

2.2 Contact Resistance Tests ............................................................................................... 15

2.2.1. Configuring Contact Resistance Tests .................................................................... 15

2.2.2. Performing a Contact Resistance Test ................................................................... 18

2.3 Performing a Transformer Winding Resistance Test ..................................................... 20

3.0 Upgrading Firmware .......................................................................................................... 22

4.0 Troubleshooting Guide ...................................................................................................... 26

LIST OF TABLES

Table 1. Auto-Ohm 10 Technical Specifications ............................................................................. 5

LIST OF FIGURES

Figure 1. Included Cable Set with Alligator Clamps (P/N 8000-0231) ............................................ 3

Figure 2. Optional 10A Rated Pistol Grip Probe (P/N 8000-0201) .................................................. 3

Figure 3. Optional 10A Rated Hand Probe (P/N 8000-0225) .......................................................... 4

Figure 4. Optional 5A Rated Hand Probe (P/N 8000-0226) ............................................................ 4

Figure 5. Auto-Ohm 10 Controls and Indicators ............................................................................. 6

Figure 6. Battery Fuse in Protective Plastic Box ............................................................................. 7

Figure 7. Panasonic Orbtronic 18650 Protected Li-ion Battery ...................................................... 8

Figure 8. Typical Auto-Ohm 10 Connection Diagram ................................................................... 14

REV 1.0

This doc

•

A ke

•

Men

• Auto

• Whe

recta

• War

• Imp

OPT

Auto-Oh

ment uses

, switch, or

names ar

Ohm 10 sc

instructio

ngle as sho

ing messag

RNING

rtant notes

OTE

ION 1

ION 2

ION 3

TION 4

TION 5

ONT

FMR

ETUP

10 USER’S

ONVEN

he followi

knob on th

referenced

een output

s are provi

n below (o

s are indic

rning mes

are indicat

te details

MANUAL

IONS U

g conventi

Auto-Ohm

as “MENU

is shown as

ed, the me

ption 3 sho

ted as:

age

d as:

100%

ED IN T

ns:

10 is indica

AME”

u item tha

ld be selec

IS DOC

ed as

[KE

should be

ed):

MENT

], [SWIT

elected is

H], [KNO

utlined wit

]

Auto-Ohm 10 USER’S MANUAL REV 1.0

1.0 INTRODUCTION

1.1 Product Overview

The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for

low-resistance-measuring applications such as the measurement of resistance in circuit breaker

contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh,

3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per

charge (10A/2 second duration) can be performed in the field. The Auto-Ohm 10 features a

built-in charger that can charge the batteries when the unit is not in use.

The Auto-Ohm 10 features a rotary knob that is used to select either the “Contact Resistance”

or “Transformer Resistance” test mode. The unit's back-lit LCD screen (128 x 64 pixels) is

viewable in both direct sunlight and low light level. Resistance readings are displayed on the

LCD screen in micro-ohms, milliohms, or ohms.

Contact Resistance Mode

The “Contact Resistance” mode can measure resistance values from 1 micro-ohm to 5,000

Ohms. The user can select from 6 different test currents: 1mA, 10mA, 100mA, 1A, 5A, 10A. The

user can also choose from 6 test times: 1 sec, 2 sec, 3 sec, 5 sec, 10 sec, 60 sec. Up to three

tests can be pre-configured with any combination of these parameters and executed with a

single push of the control switch.

The Auto-Ohm 10 also offers a “Bi-directional” test mode. In this mode, the test current is

applied in both directions to the device under test and the readings are recorded. The final test

result is the average reading of the bi-directional resistance values. An "Auto" test mode is also

available that will start a test once a user applies the test leads to the device under test. The

last three readings are displayed on the LCD screen.

Transformer Resistance Mode

In “Transformer Resistance” test mode, the Auto-Ohm 10 can measure the winding resistance

of transformers, electric motors, and generators. It provides 4 test currents (100mA, 1A, 5A,

10A) and can measure the winding resistance of a 3-phase 500KVA/12,000V transformer within

1 minute. At the end of a winding resistance test, the Auto-Ohm 10 automatically dissipates the

stored energy in the transformer.

REV 1.0 Auto-Ohm 10 USER’S MANUAL

Cables and Accessories

The Auto-Ohm 10 is furnished with a 15 ft (4.57m) cable set with alligator clamps (P/N 8000-

0231). The test current and voltage sense cables are isolated on the alligator clamps. With this

feature, only a single connection is needed to the device under test. Optional 10A rated pistol

grip probe (P/N 8000-0201), 10A rated hand probe (P/N 8000-0226), and 5A rated hand probe

(P/N 8000-0225) are also available.

Figure 1. Included Cable Set with Alligator Clamps (P/N 8000-0231)

Figure 2. Optional 10A Rated Pistol Grip Probe (P/N 8000-0233)

Auto-Ohm 10 USER’S MANUAL REV 1.0

Figure 3. Optional 10A Rated Hand Probe (P/N 8000-0225)

Figure 4. Optional 5A Rated Hand Probe (P/N 8000-0226)

REV 1.0

1.2

SPE

REA

AND

ALT

Auto-Oh

echnical

TYPE

PHYSICAL

IFICATION

UT POWER

ESISTANCE

ING RANGE

ACCURACY

BATTERIES

TO POWER

DOWN

DISPLAY

VIRONMENT

IDITY (MAX)

TUDE (MAX)

CABLES

OPTIONS

WARRANTY

The

tem

10 USER’S

pecificati

Table 1

Low Resista

14" W x 8" H

Weight: 7.8 l

100-240 Vac

Test

Current

10A

100mA

10mA

1mA

NOTE: State

Rechargeabl

Charge time:

Programmab

Backlit LCD (

Operating: -1

Storage: -30˚

Charging:0˚

90% RH @ 4

2,000m (6,5

15 ft (4.57 m

)

30 ft (9.14 m

)

probe (10A,

One year on

bove specif

erature of

MANUAL

. Auto-Ohm

ce Micro-Oh

x 12" D (36 c

s (3.54 Kg)

50/60Hz

isplay

Min

Dis

000.0 99

1.0000 9.9

10.000 99.

100.00 25

000.0 99

1.0000 9.9

10.000 99.

100.00 99

00.000 99.

100.00 99

,000.0 5,0

000.0 99

,000.0 9,9

10,000 50,

000.0 9.9

10.000 99.

100.00 50

00.000 99.

100.00 99

,000.0 5,0

accuracy for

Li-Ion, 3.7Vd

4 hours

le: 1 min, 2 mi

128 x 64 pixel

0˚C to 50˚C (+

C to 70˚C (-22

to 45˚C (+32˚

0˚ C (104˚ F)

2 ft) to full saf

)

cable set wit

)

cable set, 10

/N 8000-022

parts and labo

ications are

5°C (77°F).

10 Technic

meter

x 19.4 m x 3

lay

Displa

Unit

.9 µΩ

99 mΩ

.00 mΩ

.9 µΩ

99 mΩ

.99 mΩ

99 mΩ

.99 mΩ

0.0 mΩ

.9 mΩ

9.9 mΩ

00 mΩ

99 Ω

.00 Ω

99 Ω

.99 Ω

0.0 Ω

bi-directional

c, 3400 mAh,

, 5 min, 10 mi

), viewable in

15˚F to +122˚

˚F to +158˚F)

F to +113˚F)

on-condensin

ty specificatio

alligator clam

ft (3m) hand p

), pistol grip p

valid at no

Specificatio

l Specificati

.4 cm);

Resolutio

0.1µΩ

1µΩ

10µΩ

0.1µΩ

1µΩ

10µΩ

1µΩ

10µΩ

100µΩ

10µΩ

100µΩ

1mΩ

100µΩ

1mΩ

10mΩ

1mΩ

10mΩ

100mΩ

urrent mode

rotected (Qty

direct sunlight

)

s, power cabl

obe (5A, P/N

obe (10A, P/N

inal opera

s may cha

Accura

±0.2%±0.

±0.2%±2

±0.2%±0.

±0.2%±4

±0.2%±2

±0.2%±20

±0.2%±2

±0.2%±20

±0.2%±2

±0.2%±20

±0.2%±2

±0.2%±20

±0.2%±2

±0.2%±20

and low light l

e, cable bag

000-0226), 1

8000-0201),

ing voltage

ge without

µΩ

Ω

µΩ

Ω

µΩ

Ω

µΩ

Ω

µΩ

Ω

mΩ

Ω

mΩ

vels

ft (3m) hand

hipping case

nd at a

prior notice.

Auto-Ohm 10 USER’S MANUAL REV 1.0

1.3 Auto-Ohm 10 Controls and Indicators

The Auto-Ohm 10’s controls and indicators are shown in Figure 5. The purpose of the controls

and indicators may seem obvious, but users should familiarize themselves with them before

using the Auto-Ohm 10. Accidental misuse of the controls will usually cause no serious harm.

Users should also familiarize themselves with the safety summary information found on the

front page of this User’s Manual.

Figure 5. Auto-Ohm 10 Controls and Indicators

Inhaltsverzeichnis

Andere Vanguard Instruments Messgerät Handbücher

Vanguard Instruments

Vanguard Instruments LTCA-10 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments II Series Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments TRF-250 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments LTCA-10 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments ATRT-03 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments CT-7500 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments ATRT-03 Montageanleitung

Vanguard Instruments

Vanguard Instruments ATRT-01 S3 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments CT-8000 S3 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments TRM-20 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments IRM-5000P Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments DigiTMR S2 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments TRM-40 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments Auto-Ohm 200 S3 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments ATRT-01 S3 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments CT-7000 S3 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments WRM-10P Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung