Velleman WHADDA MMA8452 Bedienungsanleitung

USER MANUAL

3-axis digital acceleration sensor module –MMA8452

WPSE208

whadda.com

Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its

lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted

municipal waste; it should be taken to a specialized company for recycling. This device

should be returned to your distributor or to a local recycling service. Respect the local

environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Whadda! Please read the manual thoroughly before bringing this

device into service. If the device was damaged in transit, do not install or use it and contact

your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

For indoor use only.

•This device can be used by children aged from 8 years and above, and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning the use of the device in a

safe way and understand the hazards involved. Children shall not play with the device.

Cleaning and user maintenance shall not be made by children without supervision.

General Guidelines

•Refer to the Velleman®Service and Quality Warranty on the last pages of this manual.

•All modifications of the device are forbidden for safety reasons. Damage caused by

user modifications to the device is not covered by the warranty.

•Only use the device for its intended purpose. Using the device in an unauthorized way

will void the warranty.

•Damage caused by disregard of certain guidelines in this manual is not covered by the

warranty and the dealer will not accept responsibility for any ensuing defects or

problems.

•Nor Velleman Group nv nor its dealers can be held responsible for any damage

(extraordinary, incidental or indirect) –of any nature (financial, physical…) arising from

the possession, use or failure of this product.

•Keep this manual for future reference.

What is Arduino®

Arduino®is an open-source prototyping platform based on easy-to-use hardware and

software. Arduino®boards are able to read inputs –light-on sensor, a finger on a button or a

Twitter message –and turn it into an output –activating of a motor, turning on an LED,

publishing something online. You can tell your board what to do by sending a set of

instructions to the microcontroller on the board. To do so, you use the Arduino

programming language (based on Wiring) and the Arduino®software IDE (based on

Processing). Additional shields/modules/components are required for reading a twitter

message or publishing online. Surf to www.arduino.cc for more information.

Product Overview

The MMA8452Q accelerometer module is a smart, low-power, three-axis, capacitive MEMS

accelerometer with 12 bits of resolution. It is packed with embedded functions with flexible

user-programmable options, configurable to two interrupt pins. Embedded interrupt

functions allow for overall power savings relieving the host processor from continuously

polling data. It has user selectable full scales of ± 2 g/± 4 g/± 8 g with high-pass filtered

data, as well as non-filtered data available real-time.

Specifications

•supply voltage: 1.95-3.6 V

•interface voltage: 1.6-3.6 V

•current consumption: 6-165 µA

•± 2 g/± 4 g/± 8 g dynamically selectable full-scale

•output data rates (ODR): 1.56-800 Hz

•12-bit and 8-bit digital output

•I²C digital output interface (operates to 2.25 MHz with 4.7 kΩpullup)

•two programmable interrupt pins for six interrupt sources

•three embedded channels of motion detection

•orientation (portrait/landscape) detection with set hysteresis

•high-pass filter data available real-time

Pin Layout

3.3V

Power output –3.3 V output.

Vcc

Power supply –It should be between 3 and 5 V.

SDA

I²C data signal –Bi-directional data line. Voltage should not exceed power

supply.

SCL

I²C clock signal –Master-controlled clock signal. Voltage should not

exceed power supply.

SA0

I²C address –I2C least significant bit of the device I2C address.

Interrupt 2 –Programmable interrupt. Can indicate data ready,

orientation change, tap, and more.

Interrupt 1 –Programmable interrupt. Can indicate data ready,

orientation change, tap, and more.

GND

Ground –0 V/common voltage.

Example

Installation

whadda.com

Modifications and typographical errors reserved - © Velleman Group nv. WPSE208_v01

Velleman Group nv, Legen Heirweg 33 - 9890 Gavere.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Velleman Steuereinheit Handbücher

Velleman

Velleman Velbus VMB4PD Bedienungsanleitung

Velleman

Velleman VMA326 Bedienungsanleitung

Velleman

Velleman Whadda WPSE358 Bedienungsanleitung

Velleman

Velleman VMA406 Bedienungsanleitung

Velleman

Velleman VMA309 Bedienungsanleitung

Velleman

Velleman Velbus VMB1BL Bedienungsanleitung

Velleman

Velleman VMA325 Bedienungsanleitung

Velleman

Velleman HAA80 Bedienungsanleitung

Velleman

Velleman K2664 Bedienungsanleitung

Velleman

Velleman K8027 Bedienungsanleitung

Velleman

Velleman VMA301 Bedienungsanleitung

Velleman

Velleman Whadda WPI304 Bedienungsanleitung

Velleman

Velleman Whadda WPM456 Bedienungsanleitung

Velleman

Velleman VMA501 Bedienungsanleitung

Velleman

Velleman K8095 Bedienungsanleitung

Velleman

Velleman Whadda WPI474 Bedienungsanleitung

Velleman

Velleman MM111 Bedienungsanleitung

Velleman

Velleman VMA404 Bedienungsanleitung

Velleman

Velleman VMA204 Bedienungsanleitung

Velleman

Velleman VMP502 Bedienungsanleitung

Velleman

Velleman VMA203 Bedienungsanleitung

Velleman

Velleman VMA208 Bedienungsanleitung

Velleman

Velleman VMA436 Bedienungsanleitung

Velleman

Velleman VMA435 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung