Vermont Castings SB60 Bedienungsanleitung

VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

Installation and service of this replace should be

performed by qualied personnel. Vermont Cast-

ings Group recommends NFI certied profession-

als, or technicians supervised by an

NFI certied professional.

WOODBURNING FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overre and generate

poisonous gases (i.e. carbon monoxide).

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable

materials.

• Keep clothing, furniture, draperies and other ammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

SB60

SB80

NOTICE: DO NOT discard this manual!

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• DO NOT overre. Overring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specied. Failure to comply may

cause house re.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury, or death.

This replace uses SL1100 Series Chimney

2” CLEARANCE TO COMBUSTIBLES AND BUILDING INSULATION FROM CHIMNEY REQUIRED.

2VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the replace or to property.

Table of Contents

1 Product Specic & Important Safety Information

A. Fireplace Certication 4

B. Non-Combustible Materials 4

C. Combustible Materials 4

2 Getting Started

A. Typical Fireplace System 5

B. Design and Installation Considerations 6

1. Selecting Fireplace Locations 6

2. Locating Fireplace & Chimney 7

C. Tools and Supplies Needed 8

D. Inspect Fireplace and Components 8

E. Fireplace System Requirements 8

3 Framing and Clearances

A. Fireplace Dimensions 9

B. Clearances 10

Minimum Clearances to Combustibles 10

C. Construct the Chase 11

D. Unpack the Fireplace (I60 only) 12

E. Unpack the Fireplace (I80 only) 12

F. Frame the Fireplace 13

G. Secure and Level the Fireplace 14

H. Protective Metal Hearth Strips 14

I. Outside Air Kit 15

4 Chimney and Termination Requirements

A. Chimney Requirements 16

B. Offsets/Returns 17

C. Termination Requirements 18

5 Chimney Installation

A. Typical Chimney System 19

B. Assemble Chimney Sections 20

C. Install Chimney Air Kit 20

D. Secure Offset/Return 21

E. Install Ceiling Firestops 21

F. Install Attic Insulation Shield 22

G. Roof Penetration 23

H. Install Chase/Chase Top 23

I. Termination Cap Requirements 24

J. Install Termination Cap 24

6 Shrouds

A. Radiation Shield 26

B. Field Constructed Shrouds 26

1. Open Top Shroud 26

2. Mailbox Style Shroud 27

3. Roofed Style Shroud 27

7 Finishing

A. Finishing Material 28

B. Hearth Extension, Building and Finishing 29

1. Fireplace Installed Flush on the Floor

and Hearth Extension Raised to Bottom

of Firebox Opening 30

2. Raised Hearth Extension and Raised Fireplace 31

3. Fireplace Opening and Hearth Extension Flush

with the Floor 32

C. Non-Combustible Sealant Material 32

D. Sidewalls/Surrounds 33

E. Mantel and Wall Projections 34

8 Fireplace Setup

A. Gas Log/Lighter Provision 35

B. Wood Burning Inserts 35

C. Install the Refractory (I80 only) 36

9 Reference Materials

A. Chimney Components 37

B. Optional Components 40

VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

Customer:

Lot/Address

Model (circle one): SB60 SB80

YES IF NO, WHY?

Protective hearth strips installed per manual requirements. (Pg. 14)

Outside air kit installed. (Pg. 15)

Attic insulation shield installed.

Shroud is installed properly per instructions.

WARNING! Risk of Fire or Explosion! Failure to install fireplace acording to these instructions can lead to a fire or

explosion.

Verified that the chase is insulated and sealed. (Pg. 11)

Verified clearances to combustibles. (Pg. 10)

Fireplace is leveled and secured. (Pg. 14)

Hearth extension size/height decided. (Pg. 29)

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney air kit installed.

Firestops installed.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation

manual.

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Roof flashing installed.

Termination installed.

Fireplace Install

Chimney Section 4 & 5 (Pg. 16)

Shrouds Section 6 (Pg. 26)

Fi i hi

S ti 7 (P 28)

Hearth extension installed per manual requirements.

Comments communicated to party responsible

4013-302 • Rev A • 2-18-15

__________________________ by ______________________on _________

(Builder/Gen. Contractor) (Installer) (Date)

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Manual bag and all of its contents are removed from the fireplace and given to the party

responsible for use and operation.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

• Photographing the installation and copying this checklist for your file.

Combustible materials not installed in non-combustible areas.

Vermont Castings Group recommends the following:

Finishing Section 7 (Pg. 28)

Fireplace Setup Section 8 (Pg. 35)

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

All packaging and protective materials removed.

Optional doors properly installed.

Molded brick panels installed correctly.

Grate is properly installed.

Firescreen installed properly.

4VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

WARNING! Risk of Fire! Vermont Castings Group dis-

claims any responsibility for, and the warranty and agency

listing will be voided by the following actions.

DO NOT:

• installoroperatedamagedreplace

• modifyreplace

• install other than as instructed by Vermont Castings

Group

• operate the fireplace without fully assembling all

components

• overre

• installanycomponentnotapprovedbyVermontCastings

Group

• installpartsorcomponentsnotListedorapproved

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualied

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel - Iron

- Brick - Tile

- Concrete - Slate

- Glass - Plasters

• Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood - Compressed paper

- Plant bers - Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; ame proofed or

not, plastered or un-plastered

1 Product Specic & Important Safety Information

A. Fireplace Certication

This replace may be installed in sleeping rooms. This

replace is not approved for manufactured housing. If in-

stalled with a gas log set, provisions for the National Fuel

Gas Code must be met.

This replace has been tested and listed for use with

the optional components specied in this manual. These

optional components may be purchased separately and

installed at a later date. An outside air kit, gas insert, gas

log set or gas log-lighter should be installed at the time of

replace installation.

This replace system has been tested and listed in accor-

dance with UL 127 and ULC-S610 standards by Under-

writers Laboratories Inc. for installation and operation in

the United States and Canada.

VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

2 Getting Started

A. Typical Fireplace System

Figure 2.1 Typical Fireplace System

)

))

)

Non-combustible

roof flashing maintains

minimum clearance

around chimney

Additional lateral

support for chimney

above roof (or enclosed

in chase) if needed

Ceiling firestop

on floor of attic

Support straps

on rafter support

chimney

Termination cap

Chimney penetrates roof

preferably without affecting

roof rafters

Offset & Return (with hanger straps)

Framing headed off

in ceiling joists

Enclosed space above

and around fireplace

Mantel and surround

Decorative facing

and trim

Hearth extension

Factory-built fireplace

Protective metal

hearth strip(s)

Outside

combustion air

Combustible framing/header

on top of V-shaped standoffs

Chimney system

Attic insulation shield

must be used here to keep

insulation away from chimney

if attic is insulated

Storm Collar

Chimney Air Kit

Required in

Canada. Outlet

must be no

less than 4 ft.

(1.22 m) off

ground level.

6VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

In an exterior

chase or projecting

into a garage

Across a

corner

As a room

divider

Along a wall

B A

48 in.

(1219 mm)

min.

Note: SB60 - 1 in. (25 mm)

SB80 - 1 1/2 in. (38 mm)

minimum distance from sides

& back of fireplace to

combustible materials.

Both - 1/2 in. (13 mm)

minimum at nailing flanges.

1/2 in. (13 mm)

all configurations

*8 in. (203 mm) extra space

included for outside air

connection. If outside air duct has

no bend, this dimension may be

reduced as long as minimum

clearances are met.

A B C D E F G H

inches 45 1/2 53 1/2 85 42 1/2 19 3/8 60 1/8 28

mm 1156 1359 2159 1080 492 1527 711

inches

59 1/2 92 3/4 46 3/8 21 1/2 65 5/8 28 1/2

mm 1308 1511 2356 1178 546 1667 724

Model

SB60

SB80

24 in. (610 mm)

Minimum from FP opening to a

perpendicular wall.

51 1/2

Figure 2.2 Fireplace Locations

NOTICE:

• Illustrationsandphotosreecttypicalinstallationsand

are FORDESIGNPURPOSESONLY.

• Illustrations/diagramsarenotdrawntoscale.

• Actualinstallation/appearancemayvaryduetoindividual

design preference.

• VermontCastingsGroupreservestherighttoalterits

products.

NOTICE: In addition to these framing dimensions, also

reference the following section:

• Clearances (Section 3).

NOTICE:

SB60-Aminimum1in.airclearanceattheback

andaminimum1in.airclearancetothesidesof

thereplaceassemblymustbemaintained.

SB80-Aminimum11/2in.airclearanceatthe

backandaminimum11/2in.airclearancetothe

sidesofthereplaceassemblymustbemain-

tained

Chimney sections at any level require a 2

in. minimum air space clearance between

the framing and chimney sections.

B. Design and Installation Considerations

NOTICE: Checkbuildingcodespriortoinstallation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, re

ofcials or authorities having jurisdiction over restrictions,

installation inspection and permits.

• Before installing, determine the following:

- Where the replace is to be installed.

- The vent system conguration to be used.

- Gas supply piping.

- Electrical wiring.

- Framing and nishing details.

- Whether optional accessories - devices such as a

fan, wall switch or remote control - are desired.

1. Selecting Fireplace Locations

This replace may be used as a room divider, installed

along a wall, across a corner or used in an exterior chase.

See Figure 2.2.

Locating the replace in a basement, near frequently

opened doors, central heat outlets or returns, or other

locations of considerable air movement can affect the

performance.

Consideration should be given to these factors before

deciding on a location.

VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

2. Locating Fireplace & Chimney

Location of the replace and chimney will affect perfor-

mance.

• Install within the warm airspace enclosed by the building

envelope. This helps to produce more draft, especially

during lighting and die-down of the re.

• Installing the replace in a basement is not recommended.

• Penetrate the highest part of the roof. This minimizes

the effects of wind loading.

• Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

• Minimize the use of chimney offsets.

• Consider the replace location relative to oor and ceiling

and attic joists.

• Take into consideration the termination requirements in

Sections 4 and 5.

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Figure 2.3 Recommended Chimney Locations

• Install the outside air kit with the intake facing prevailing

winds during the heating season.

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the replace.

• Avoid installing the replace near doors, walkways or

small isolated spaces.

• Recessed lighting should be a “sealed can” design.

• Attic hatches weather stripped or sealed.

• Attic mounted duct work and air handler joints and seams

taped or sealed.

8VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

C. Tools and Supplies Needed

Before beginning the installation be sure the following

tools and building supplies are available:

Reciprocating saw Framing material

Pliers Non-combustible sealant

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

D. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged

parts could impair safe operation. DO NOT install dam-

aged,incompleteorsubstitutecomponents.Keepre-

place dry.

• Inspect replace for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benet.

E. Fireplace System Requirements

The VCG replace system requirements consist of the

following:

• Fireplace

- Refractory (included with replace)

- Firescreen (included with replace)

- Hearth Extension

• Outside Air System

- Air Inlet Hood (included with replace)

- Flex (required, sold separately)

• Chimney System

- Chimney air kit (required in Canada, sold separately)

- Attic Insulation Shield (included with replace)

- Chimney termination cap (required, sold separately)

- SLA10 adapter (required in Canada, sold separately)

• Non-combustible nish material

VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

3 Framing and Clearances

A. Fireplace Dimensions

Gas

Knockout

8-5/8 in.

(219 mm)

9-5/8 in.

(244 mm)

9-1/2 in.

(241 mm)

Outside Air

9-1/4 in.

(235 mm)

Gas Knockout

18-1/2 in.

(470 mm)

8-5/8 in.

(219 mm)

49-5/8 in.

(1260 mm) 28-1/2 in.

(724 mm)

55-1/2 in.

(1410 mm)

(effective height)

49-1/8 in.

(1248 mm)

59-1/4 in.

(1505 mm)

7-5/8 in.

(194 mm) 36 in.

(914 mm)

28-5/8 in.

(727 mm)

14-3/8 in.

(365 mm)

44-1/2 in.

(1130 mm)

27-1/2 in.

(699 mm)

9-1/2 in.

(241 mm)

Figure 3.1 Fireplace Dimensions

28-1/2 in.

(724 mm)

55-1/2 in.

(1410 mm)

(Efective Height

49-1/8 in.

(1248 mm)

49-5/8 in.

(1260 mm)

59-1/4 in.

(1505 mm)

7-5/8 in.

(194 mm) 42 in.

(1067 mm)

Gas

Knockout

18-1/2 in.

(470 mm)

8-5/8 in.

(219 mm)

Gas

Knockout

8-5/8 in.

(219 mm)

9-5/8 in.

(244 mm)

9-1/2 in.

(241 mm)

9-1/4 in.

(235 mm)

Outside

Air

34-1/2 in.

(876 mm)

9-1/2 in.

(241 mm)

27-1/2 in.

(699 mm)

50-1/2 in.

(1283 mm)

SB60

SB80

10 VCG Biltmore Series • SB60/SB80 • 4013-300 Installers Manual • Rev A • 02/18/15

B. Clearances

WARNING! Risk of Fire!

You must comply with all minimum air space clearances

tocombustiblesasspeciedinFigure3.2.DO NOTpack

required air spaces with insulation or other materials.

Framing or nishing material used on the front of, or in

frontof,thereplacecloserthantheminimumslistedmust

be constucted entirely of non-combustible materials (i.e.,

steel studs, concrete board, etc.). Failure to comply may

causere.

Figure 3.2 Clearances to Combustible Materials

Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA

Fireplace to backwall (I60) 1 in. (25 mm)

Fireplace to backwall (I80) 1 1/2 in. (38 mm)

Fireplace to sidewall (I60) 1 in. (25 mm)

Fireplace to sidewall (I80) 1 1/2 in. (38 mm)

Top standoffs to header 0 in. (0 mm)

Door opening to sidewall 24 in. (610 mm)

MANTEL

Mantel minimum height 12 in. (305 mm)

above opening

Maximum mantel depth 12 in. (305 mm)

(insulation)

0 in. to level

of standoffs

Attic

Insulation

Shield

(ceiling)

(roof)

(attic)

(ceiling)

Ceiling Firestop

Offset/Return (secured

with hanger straps)

Storm Collar

Roof Flashing

Clearance to back &

sides of appliance

I60 - 1 in. (25 mm)

I80 - 1 1/2 in. (38 mm)

(except at nailing flanges

where it is 1/2 in. [13 mm])

Must have 2 in. (51 mm)

minimum clearance

to header

0 in.

to floor

2 in. (51 mm) min.

Shaded areas

represent

2 in. (51 mm) min.

air space clearance

required around pipe

Combustible Object

48 in.

1219 mm

Adapter attached here (not shown)

Note: Chimney air kit and 11-10

in./279-254 mm adapter are

not shown, but are required in

Canada.

Andere Handbücher für SB60

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vermont Castings Holzofen Handbücher

Vermont Castings

Vermont Castings Defiant 1945CE Montageanleitung

Vermont Castings

Vermont Castings Defiant 1610 Montageanleitung

Vermont Castings

Vermont Castings Encore 2040-CAT-C Bedienungsanleitung

Vermont Castings

Vermont Castings Resolute Acclaim 2490 Kurzanleitung

Vermont Castings

Vermont Castings The Aspen 1920 Montageanleitung

Vermont Castings

Vermont Castings 2040ce Bedienungsanleitung

Vermont Castings

Vermont Castings WR1000L02 Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant FlexBurn 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings Madison 1655 Montageanleitung

Vermont Castings

Vermont Castings Defiant 1945 Montageanleitung

Vermont Castings

Vermont Castings Encore 1450 Montageanleitung

Vermont Castings

Vermont Castings Encore 1450 Montageanleitung

Vermont Castings

Vermont Castings Encore 2550CE Montageanleitung

Vermont Castings

Vermont Castings VSW20 Planungshandbuch

Vermont Castings

Vermont Castings SSW30FTAL Montageanleitung

Vermont Castings

Vermont Castings Seville 1636 Montageanleitung

Vermont Castings

Vermont Castings Defiant 1610CE Montageanleitung

Vermont Castings

Vermont Castings Defiant 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings 2115 Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant 1945CE Montageanleitung

Vermont Castings

Vermont Castings Defiant 1945 Montageanleitung

Vermont Castings

Vermont Castings The Aspen 1920 Montageanleitung

Vermont Castings

Vermont Castings 2115 Bedienungsanleitung

Vermont Castings

Vermont Castings Dutchwest Small 2460 Handbuch

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung