Vermont Castings Dutchwest Small 2460 Handbuch

Damper Rod Replacement

For 8 months prior to February of 1994, the ’93 series was made with a threaded rod

installed in a threaded hole in the inner top as per earlier models made from 1990 - 1993. In

February of 1994, the thread system that had a tendency to jam was updated to the current

system with no threads. These instructions show you how to replace the old damper with the

new system.

Models affected: Small 2460 & 2181; Large 2461 & 2183; Extra-Large 2462 & 2184

Please read these instructions carefully before beginning the installation.

PARTS NEEDED:

•Damper Rod; (Small – 7001154, Large - 7001131, or Extra-Large – 7001160)

•5/8” i.d. washer (1202561)

•5/8” retaining ring (1203058)

TOOLS:

•7/16” socket or open-end wrench

•Needle nose pliers

•1/8” Allen wrench

Fig. 3 Remove the top

PROCEDURE:

1. Evenly loosen and then remove all four bolts that secure

the top plate to the sides of the stove (Fig. 3).

2. Remove the top plate. Carefully remove the refractory package from within the inner top.

Leave the catalytic element in place, but take care not to damage it (Fig.4).

3. Remove both the nut and bolt (a) that secure the damper adjuster to the damper using a

7/16” socket or open-end wrench. The nut must be reached from inside the stove.

Also, remove the two damper tab bolts and damper tabs

(b), Fig 5. Remove the damper.

Fig. 3 Remove the Top

Fig. 4 Remove Refractory

Dutchwest Convection 90 - 94 Service Procedure

Fig. 5 Remove Damper

WoodmansPartsPlus.com

4. Rotate the damper crank forward and flip

the adjuster plate upside-down, (you will

see #950 cast into the plate) (Fig. 6). Slide

the adjuster plate over to the left end of the

crank.

5. Disconnect the old damper rod from the crank by

rotating both the crank and the adjuster as a unit in a

counter-clockwise direction (facing the left end of

the stove). As you rotate the crank and adjuster

plate through the high point of the arc, you will

need to maneuver the adjuster plate somewhat to

clear the back plate of the stove (Fig. 7). Unscrew

the damper rod from the stove.

6. Loosen the set screw with the Allen wrench to remove the faucet handle from the old rod and

re-install the handle on the new damper operating rod.

7. Install the new operating rod. Place the 5/8” washer onto the rod between the outer and

inner walls (Fig. 8), then insert the end of the rod into the crank. Properly oriented, both

the handle and the crank should be pointing downward.

Fig. 6

Fig.

Figure 8

Figure

WoodmansPartsPlus.com

8. Push the washer against the stove wall and use needle nose pliers to insert the retaining clip

onto the groove in the rod to lock the rod in place (Fig. 9 previous page).

NOTE: This is a good time to check the condition of the damper gasket and replace it, if

necessary.

9. Re-position the damper adjuster plate right side up and secure it to the damper using

the 7/16” bolt and nut.

10. Check the damper rod/damper plate action to be sure that the damper seals tightly in the

closed position. Rotate the adjustment bolt (a in Fig. 10), clockwise to improve the seal

against the gasket.

11. Inspect the catalytic element and carefully clean any debris from it using a vacuum. Be sure

the interam gasket (b in Fig 10) is properly positioned around the element. Replace the

refractory package.

12. Replace the top plate and secure it with the bolts and washers used previously. Gradually

tighten the bolts evenly, alternating from side to side.

Figure

WoodmansPartsPlus.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vermont Castings Holzofen Handbücher

Vermont Castings

Vermont Castings Defiant Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant FlexBurn Montageanleitung

Vermont Castings

Vermont Castings Defiant FlexBurn 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings Aspen C3 Bedienungsanleitung

Vermont Castings

Vermont Castings Resolute Acclaim 2490CE Montageanleitung

Vermont Castings

Vermont Castings Defiant 1610 Bedienungsanleitung

Vermont Castings

Vermont Castings MONTPELIER II Bedienungsanleitung

Vermont Castings

Vermont Castings 2115 Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant 1610 Bedienungsanleitung

Vermont Castings

Vermont Castings The Intrepid 2 1990CE Montageanleitung

Vermont Castings

Vermont Castings Defiant 1945 Montageanleitung

Vermont Castings

Vermont Castings Encore Flexburn 2040 Montageanleitung

Vermont Castings

Vermont Castings Defiant 1945CE Montageanleitung

Vermont Castings

Vermont Castings Encore 1450 Bedienungsanleitung

Vermont Castings

Vermont Castings 2040ce Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant FlexBurn 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings Encore 1450 Montageanleitung

Vermont Castings

Vermont Castings Defiant 1945 Montageanleitung

Vermont Castings

Vermont Castings Windsor WR270007 Bedienungsanleitung

Vermont Castings

Vermont Castings Concord 1660 Bedienungsanleitung

Vermont Castings

Vermont Castings Defiant 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid II Bedienungsanleitung

Vermont Castings

Vermont Castings WR1000L02 Bedienungsanleitung

Vermont Castings

Vermont Castings 410 Montageanleitung

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung