Vertex Standard VX-2R Bedienungsanleitung

FCC ID: K66VX-2R

Alignment

Vertex Standard Co., Ltd.

VX-2R Alignment

Introduction

The VX-2R is carefully aligned at the factory for the specified performance across

the amateur band. Realignment should therefore not be necessary except in the

event of a component failure. Only an authorized Yaesu representative should

perform all component replacement and service, or the warranty policy may be

void. The following procedures cover the adjustments that are not normally

required once the transceiver has left the factory. However, if damage occurs and

some parts subsequently are replaced, realignment may be required. If a sudden

problem occurs during normal operation, it is likely due to component failure;

realignment should not be done until after the faulty component has been

replaced.

We recommend that servicing be performed only by authorized Yaesu service

technicians who are experienced with the circuitry and fully equipped for repair

and alignment. If a fault is suspected, contact the dealer from whom the

transceiver was purchased for instructions regarding repair. Authorized Yaesu

service technicians realign all circuits and make complete performance checks to

ensure compliance with factory specifications after replacing any faulty

components. Those who do undertake any of the following alignments are

cautioned to proceed at their own risk. Problems caused by unauthorized attempts

at realignment are not covered by the warranty policy. Also, Yaesu reserves the

right to change circuits and alignment procedures in the interest of improved

performance, without notifying owners.

Under no circumstances should any alignment be attempted unless the normal

function and operation of the transceiver are clearly understood, the cause of the

malfunction has been clearly pinpointed and any faulty components replaced, and

realignment determined to be absolutely necessary.

The following test equipment (and familiarity with its use) is necessary for

complete realignment. Correction of problems caused by misalignment resulting

from use of improper test equipment is not covered under the warranty policy.

While most steps do not require all of the equipment listed, the interactions of

some adjustments may require that more complex adjustments be performed

afterwards.

Do not attempt to perform only a single step unless it is clearly isolated

FCC ID: K66VX-2R

Alignment

Vertex Standard Co., Ltd.

electrically from all other steps. Have all test equipment ready before beginning

and, follow all of the steps in a section in the order presented.

Required Test Equipment

□RF Signal Generator with calibrated output level at 500 MHz

□Deviation Meter (linear detector)

□In-line Wattmeter with 5% accuracy at 500 MHz

□50-Ω, 10-W RF Dummy Load

□8-ΩAF Dummy Load

□Regulated DC Power Supply adjustable from 3 to 15 VDC, 2A

□Frequency Counter: 0.2-ppm accuracy at 500 MHz

□AF Signal Generator

□AC Voltmeter

□DC Voltmeter: high impedance

□VHF Sampling Coupler

□SINAD Meter

Alignment Preparation & Precautions

A 10-W RF load and in-line wattmeter must be connected to the main antenna

jack in all procedures that call for transmission, alignment is not possible with an

antenna. After completing one step, read the next step to see if the same test

equipment is required. If not, remove the test equipment (except dummy load and

wattmeter, if connected) before proceeding.

Correct alignment requires that the ambient temperature be the same as that of

the transceiver and test equipment, and that this temperature be held constant

between 20~30°C (68~86°F). When the transceiver is brought into the shop from hot

or cold air, it should be allowed some time to come to room temperature before

alignment. Whenever possible, alignments should be made with oscillator shields

and circuit boards firmly affixed in place. Also, the test equipment must be

thoroughly warmed up before beginning.

Note:

Signal levels in dB referred to in the alignment procedure are based on 0dBm=0.5

FCC ID: K66VX-2R

Alignment

Vertex Standard Co., Ltd.

Test Setup

Set up the test equipment as shown below for transceiver alignment, apply 6 V

DC power to the transceiver. Refer to the drawings for Alignment Points.

Internal System Alignment Routine

This uses a programmed routine in the transceiver which simplifies many

previously complex discrete component settings and adjustments with digitally-

controlled settings via front panel buttons and LCD indications.

To begin, set the transceiver to the center of the 50MHz, 144MHz, 220MHz and

430MHz bands. Next, select the 430MHz band, then turn the transceiver off.

Now, press and hold the [BAND], [H/L] and [V/M] button together while

powering the radio on again. The display will show the first setting.

Note that the first few settings are not adjustable and are left as set from the

factory.

In the alignment process, each adjustment is selected by rotating the DIAL.

Alignment is performed by:

○ Pressing the [V/M] button;

○ Injecting a signal of the required frequency and level; then

○ Pressing the [V/M] button after a level setting or adjustment is made. This

second pressing of the [V/M] button store the entry.

To exit the alignment routine, press the [HM/RV] button. After performing the

system alignment in its entirety, individual settings can be returned to and adjust

should the need arise

In the section to follow, typical default values (as set at the factory) are shown in

brackets (e.g. [119]), to serve as a general guideline. As each transceiver is

individually optimized at the factory, the precise settings for the transceiver on

your bench may be slightly different.

FCC ID: K66VX-2R

Alignment

Vertex Standard Co., Ltd.

PLL Reference Frequency (PLL REF)

Transmit and adjust the counter frequency for within ±300Hz by rotating the

DIAL, then press the [V/M] button. Rotate the DIAL to select the next setting.

430MHz band Alignment

○

Squelch Hysteresis Adjust (HIS)

Rotate the DIAL for minimum squelch hysteresis, then press the [V/M] button.

Rotate the DIAL to select the next setting.

○

Squelch Preset Threshold (tHL)

Inject a -15dBµ RF signal (1 kHz tone @ ±3.5kHz deviation), then press the [V/M]

button. Rotate the DIAL to select the next setting.

○

Squelch Preset Tight (tIg)

Adjust the generator level for a -4dBµ signal, then press the [V/M] button. Rotate

the DIAL to select the next setting.

○

Low-Scale S-1 Adjustment (S1)

Adjust the generator level to -7dBµ (1 kHz tone @ ±3.5kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

S-Meter Full-Scale Adjust (S9)

Adjust the generator level to +20dBµ (1 kHz tone @ ±3.5kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

Wide Low-Scale S-1 Adjustment (S1)

Adjust the generator level to 0dBµ (1 kHz tone @ ±20kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

Wide S-Meter Full-Scale Adjust (S9)

Adjust the generator level to +20dBµ (1 kHz tone @ ±20kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

High TX Power Adjust (HPo)

Transmit and adjust the output power level for 2W ±0.3W by rotating DIAL, then

press the [V/M] button. Rotate the DIAL to select the next setting.

○

Low TX Power Adjust (LPo)

Transmit and adjust the output power level for 50 mW ±30 mW by rotating DIAL,

then press the [V/M] button. Rotate the DIAL to select the next setting.

○

TX Deviation Adjustment (dEV)

Transmit and adjust the deviation for 4.2KHz ±0.2KHz by rotating DIAL, then

press the [V/M] button. Rotate the DIAL to select the next setting.

This completes the UHF band internal alignment routine, to save all settings and

exit, press [BAND] button.

FCC ID: K66VX-2R

Alignment

Vertex Standard Co., Ltd.

144MHz band Alignment

○

Squelch Hysteresis Adjust (HIS)

Rotate the DIAL for minimum squelch hysteresis, then press the [V/M] button.

Rotate the DIAL to select the next setting.

○

Squelch Preset Threshold (tHL)

Inject a -15dBµ RF signal (1 kHz tone @ ±3.5kHz deviation), then press the [V/M]

button. Rotate the DIAL to select the next setting.

○

Squelch Preset Tight (tIg)

Adjust the generator level for a -4dBµ signal, then press the [V/M] button. Rotate

the DIAL to select the next setting.

○

Low-Scale S-1 Adjustment (S1)

Adjust the generator level to -7dBµ (1 kHz tone @ ±3.5kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

S-Meter Full-Scale Adjust (S9)

Adjust the generator level to +20dBµ (1 kHz tone @ ±3.5kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

Wide Low-Scale S-1 Adjustment (S1)

Adjust the generator level to 0dBµ (1 kHz tone @ ±20kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

Wide S-Meter Full-Scale Adjust (S9)

Adjust the generator level to +20dBµ (1 kHz tone @ ±20kHz deviation), then press

the [V/M] button. Rotate the DIAL to select the next setting.

○

High TX Power Adjust (HPo)

Transmit and adjust the output power level for 3W ±0.3W by rotating DIAL, then

press the [V/M] button. Rotate the DIAL to select the next setting.

○

Low TX Power Adjust (LPo)

Transmit and adjust the output power level for 50mW ±30mW by rotating DIAL,

then press the [V/M] button. Rotate the DIAL to select the next setting.

○

TX Deviation Adjustment (dEV)

Transmit and adjust the deviation for 4.2KHz ±0.2KHz by rotating DIAL, then

press the [V/M] button. Rotate the DIAL to select the next setting.

This completes the UHF band internal alignment routine, to save all settings and

exit, press [BAND] button.

Inhaltsverzeichnis

Andere Vertex Standard Transceiver Handbücher

Vertex Standard

Vertex Standard EVX-531 Bedienungsanleitung

Vertex Standard

Vertex Standard VX-5500V Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1400 Bedienungsanleitung

Vertex Standard

Vertex Standard VXA-300 Pilot III Bedienungsanleitung

Vertex Standard

Vertex Standard VXA-710 SPIRIT Bedienungsanleitung

Vertex Standard

Vertex Standard VX-820 series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-410 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1210 Bedienungsanleitung

Vertex Standard

Vertex Standard VX-2100 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-925E Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1210 Bedienungsanleitung

Vertex Standard

Vertex Standard VX-800 Bedienungsanleitung

Vertex Standard

Vertex Standard VXA-300 Pilot III Bedienungsanleitung

Vertex Standard

Vertex Standard VX-230 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-3R Handbuch

Vertex Standard

Vertex Standard VX-160U Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1700 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1700 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-351PMR446 Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1210 Bedienungsanleitung

Vertex Standard

Vertex Standard VX-450 series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-1700 Series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-420E series Bedienungsanleitung

Vertex Standard

Vertex Standard VX-6000L Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung