VX-925E OPERATING MANUAL ENGLISH
ATTENTION IN CASE OF USE
This transceiver works on frequencies which are not generally permitted. For
frequency allocation, apply for a license at your local spectrum management
authority. For actual usage contact your dealer or sales shop in order to get your
transceiver adjusted to the allocated frequency range.
LIST OF THE PRACTICABLE AREA
AUT BEL BGR CYP CZE DEU DNK ESP EST FIN FRA
GBR GRC HUN IRL ITA LTU LUX LVA MLT NLD POL
PRT ROU SVK SVN SWE CHE ISL LIE NOR
CONTROL & SWITCHES
Microphone
Speaker
MIC/SP Jack
VOL/PWR Knob
CH (Channel) Selector
Battery Pack Latch
Programmable Key
Programmable Key
Push To Talk (PTT) Switch
Antenna Jack
Tone 2 Key LCD (LCD Version)
Tone 1 Key
MONITOR Key TOGGLE Switch
LED Indicator
Glows Green Transmitting
Blinking Red Busy Channel
BAISIC OPERATION
rTurn the top panel’s VOL/PWR knob clockwise to turn on the radio.
rTurn the top panel’s CH selector knob to choose the desired operating
channel.
rRotate the VOL/PWR knob to set the desired audio level.
If no signal is present, press and hold in the MONITOR key; background noise
will now be heard, and you may use this to set the VOL/PWR knob for the
desired audio level. Press and hold in the MONITOR key to quiet the noise and
resume normal (Quiet) monitoring.
rTo transmit, press and hold in the PTT switch. Speak into the microphone area
of the front panel grille in a normal voice level. To return to the Receive mode,
release the PTT switch.
rPress (or press and hold in) the Programmable key (or switch the TOGGLE
switch) to activate the function which is corresponding with that key or switch.
rTurn the top panel’s VOL/PWR knob fully counter clockwise to turn off the
radio.
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD (AUSTRALIA)PTY.,
LTD.
Normanby Business Park, Unit 14/45 Normanby Road
Notting Hill 3168, Victoria, Australia
Copyright 2009
VERTEX STANDARD CO., LTD.
All rights reserved.
No portion of this manual
may be reproduced
without the permission of
VERTEX STANDARD CO., LTD.
Notification of intended purpose of product use: This product is suitable for
use in private mobile radio (PMR) systems. It utilises operating frequencies not
harmonised in intended country of use.
Declaration of Conformity: Vertex Standard Declares this
product complies with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Note: A copy of signed and dated Declaration of Conformity can be obtained via
your local Vertex Standard Sales representatives.
For a copy of the complete Owners Manual go to http://www.vertexstandard.com/
manuals
FOR HAND HELD TRANSCEIVERR
rPlease read this manual carefully to become familiar with the features of this
transceiver.
rDo not transmit the radio without an antenna connected.
rWhen transmitting, hold the radio in a vertical position with its microphone 2.5
to 5 cm away from your mouth and keep the antenna at least 2.5cm away from
your head.
rThe radio must be used with a maximum operating duty cycle not exceeding
50 %, in typical Push-to-Talk (PTT) configurations. DO NOT transmit for more
than 50 % of total radio use time (50 % duty cycle). Transmitting more than
50 % of the time can cause RF exposure compliance requirements to be
exceeded.
The radio is transmitting when the red LED on the top of the radio is illuminated.
You can cause the radio to transmit by pressing the PTT button or by using the
VOX headset, if the radio is supported.
rAlways use the Vertex Standard authorized Battery Pack.
rRisk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
rPerform the battery charging where the ambient temperature range 0 °C to
+45 °C. Charge out of this range could cause damage to the battery pack.
rBattery Pack shall not be exposed to excessive heat such as sunshine, fire or
the like.
rAlways use Vertex Standard authorized accessories.
Vertex Standard shall not be liable for any damage or accidents such as fire,
leakage or explosion of batteries, etc., caused by the malfunction of non-
Vertex Standard accessories.
rThis radio generates RF electromagnetic energy during transmit mode.
This radio is designed for and classified as occupational use only, meaning
it must be used only during the course of employment by individuals aware
of hazardous, and the ways to minimize such hazardous. This radio is not
intended for use by the General Population in an uncontrolled environment.
FOR MOBILE TRANSCEIVER
WARNING: DO NOT operate the radio when any person(s) (bystanders) outside
the vehicle are within the distances shown in the chart at the bottom of this
section.
Safety Training information: Antennas used for this transmitter must not exceed
an antenna gain of 0 dBd. The radio must be used in vehicle-mount configurations
with a maximum operating duty factor not exceeding 50 %, in typical Push-to-Talk
configurations.
This radio is restricted to occupational use, work related operations only where
the radio operator must have the knowledge to control the exposure conditions of
its passengers and bystanders by maintaining the minimum separation distance
shown below.
Antenna Installation: For rear deck trunk installation, the antenna must be
located at least 1 m (VHF model) or 0.8 m (UHF model) away from rear-seat
passengers. For roof top installations, the antenna must be placed in the center
of the roof.
Warning!: The HIGH voltage is applied to the antenna terminal of the
transceiver while transmitting.
Do not touch the TX RF section absolutely while transmitting.
Caution: The radio can become hot.
Do not operate the radio continuously in transmission mode for longer than
7 minutes. Ensure enough standby/reception time for cool-down between
transmission periods. Be sure that TOT timer is correctly installed and
properly working. Avoid touching the rear bottom of the transceiver’s body
while transmission.
Automotive Directive E-Marking: In order to meet the requirements of the
Automotive Directive (72/245/ECC, as amended by 95/54EC) this product must
be installed in a vehicle in accordance with the vehicle manufacturers guide lines
and the installation u\instructions detailed in the product Installation Manual.
COMMON INFORMATION
DISPOSAL OF YOUR ELECTRONIC & ELECTRIC EQUIPMENT
Products with the symbol (crossed-out wheeled bin) cannot
be disposed as household waste. Electronic and Electric Equipment
should be recycled at a facility capable of handling these items and
their waste byproducts. In EU countries, please contact your local
equipment supplier representative or service center for information
about the waste collection system in your country.
VX-925E100219.indd2VX-925E100219.indd2 10.2.194:40:08PM10.2.194:40:08PM
EC075N160
