Vertiv Liebert ITA2 Bedienungsanleitung

Vertiv | Liebert®ITA2™Battery Cabinet Quick-Start Guide | Rev. 0 | 01/18 | 1

LIEBERT®ITA2™BATTERY CABINET

Quick-Start Guide

The complete Liebert ITA2 Battery Cabinet user manual is available at Vertiv’s Web site,

www.vertivco.com/en-us/products-catalog/critical-power/uninterruptible-power-supplies-ups/ or by

using the QR code, below right.

Unpacking and Inspection

Unpack and inspect the Liebert ITA2 Battery Cabinet.

1. If any problem is found, file a damage claim with the carrier immediately and send a copy to Vertiv at:

Vertiv

1050 Dearborn Drive

P.O. Box 29186

Columbus, Ohio 43085 USA

2. Check the contents against the delivery list. If any problem is found, notify your local Vertiv

representative immediately.

Connecting One Battery Cabinet

Do not reverse the polarity of the battery cables. Before replacing the battery cabinet and connecting the battery

cables, ensure the battery breaker on the rear of the battery cabinet is open (Off).

Installing Battery Insulating Plates

The battery terminals need insulating plates to guarantee the sufficient

insulation distance between the battery external cables connection to

protect against faults such as arcing and short circuits.

To install the insulating plates:

1. Crimp the user external cable on the battery terminals.

2. Crimp the battery insulating plates, and use the screws to fasten the OT terminals

and insulating plates together onto the terminal block.

Installing the Battery Cabinet—Connecting Battery Cabinet Cables

When more than one string is installed, use the factory-provided cable to connect the battery cabinets, use the

factory-provided cable shown in Figure 1, Terminals A of the first string connects to the UPS. Terminal B of the

first string will connect to Terminal A of the second string.

Figure 1 Cables between Liebert ITA2 and battery cabinets

NOTE

The installation sequence of the OT terminals and insulating plates must be strictly observed, otherwise the

user external cables connection will be separated.

CABLES FOR UPS TO ONE BATTERY STRING

CABLES FOR ADDITIONAL BATTERY STRINGS

1. Communication Cable

2. Power Cable (UPS to

Battery String 1)

3. Terminal A of Battery

Module 1

4. Terminal A of Battery

Module 1

5. Terminal A of Battery

Module 1;

6. Battery String 2

7. Terminal B of Battery

Module 2;

8. Battery String 2

Vertiv | Liebert®ITA2™Battery Cabinet Quick-Start Guide | Rev. 0 | 01/18 | 2

The cable connections between the battery cabinet and the UPS are shown in Figure 2.

Figure 2 Cable the UPS to two battery strings in parallel

1. PE (Battery Ground) on UPS 2. BAT - on UPS 3. BAT N on UPS 4. BAT + on UPS

5. Extension Cable 6. Terminal A, Battery Cabinet 1 7. Terminal B, Battery Cabinet 1 8. Terminal A, Battery Cabinet 2

9. Terminal B, Battery Cabinet 2 10. Terminal A, Battery Cabinet 3 11. Terminal A, Battery Cabinet 4 12. Communication Port 1

of Battery Cabinet 3

13. RJ-45 Communication Cables 14. Communication Port 2

of Battery Cabinet 1

15. Communication Port 1

of Battery Cabinet 1

REPO

Vertiv | Liebert®ITA2™Battery Cabinet Quick-Start Guide | Rev. 0 | 01/18 | 3

Connecting Additional Battery Cabinets

The factory-provided extension cable has a PP45 connector on each end, as shown in Figure 3. It connects the

battery strings in parallel to extend the backup time of the UPS. The factory-provided communication cable has

an RJ-45 terminal on each end for communicating with the battery cabinets.

Figure 3 Battery extension cable

To connect power cables:

1. Verify that the battery breakers are in the open (Off) position before connecting or disconnecting battery cables.

2. If the Liebert ITA2 UPS has been connected to a battery cabinet, remove the connection cables.

3. Connect the extension cable to the corresponding battery ports on the two battery cabinets. Verify that the connector colors

align and press the cable in firmly to fully seat the connectors

4. Tighten the captive screws on the extension cable to prevent the extension cable from loosening.

5. Connect the communication cable to the RJ-45 port on the battery cabinet to the UPS as shown in Figure 2.

Figure 2 shows two battery strings connected in parallel.

To connect the battery cabinets to the Liebert ITA2 UPS, refer to the UPS user manual, SL-00030, which

shipped with the UPS and is available at Vertiv’s Web site:

www.vertivco.com/en-us/products-catalog/critical-power/uninterruptible-power-supplies-ups/

and logos referred to are trade names, trademarks or registered trademarks of their respective owners.

While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and

disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to

change without notice.

1. Port B 2. Communication Cable

3. Port A 4. Power Cable

Technical Support Three-Phase UPS & Power Systems

800-543-2378

Outside North America: 614-841-6598

United States

SL-26257QS_REV0_01-18

1050 Dearborn Drive

P.O. Box 29186

Columbus, OH 43085

www.vertivco.com

Andere Handbücher für Liebert ITA2

Inhaltsverzeichnis

Andere Vertiv Stromversorgung Handbücher

Vertiv

Vertiv Liebert APM 400 Bedienungsanleitung

Vertiv

Vertiv NetSure 801DB NVGB Benutzerhandbuch

Vertiv

Vertiv NetSure 2100 Series Bedienungsanleitung

Vertiv

Vertiv NetSure 5000 Series Bedienungsanleitung

Vertiv

Vertiv NetSure 512NGBB Bedienungsanleitung

Vertiv

Vertiv NetSure 531 AC1 Bedienungsanleitung

Vertiv

Vertiv NetSure 731 A91 Bedienungsanleitung

Vertiv

Vertiv NetSure-48 VDC Power System 502NGFB Bedienungsanleitung

Vertiv

Vertiv NetSure ITS Series Bedienungsanleitung

Vertiv

Vertiv NetSure PLM80142 Bedienungsanleitung

Vertiv

Vertiv NetSure 588820200SK001 Bedienungsanleitung

Vertiv

Vertiv NetSure 5100 Series Bedienungsanleitung

Vertiv

Vertiv PSP500MT3-230U Bedienungsanleitung

Vertiv

Vertiv NetSure 710 Series Bedienungsanleitung

Vertiv

Vertiv NetSure7100 Series Bedienungsanleitung

Vertiv

Vertiv NetSure 502NGFB Series Bedienungsanleitung

Vertiv

Vertiv NetSure 2100 Series Bedienungsanleitung

Vertiv

Vertiv NetSure 211 Series Bedienungsanleitung

Vertiv

Vertiv NetSure HVT F02 CK1 Bedienungsanleitung

Vertiv

Vertiv NetSure 8200 Series Bedienungsanleitung

Vertiv

Vertiv NetSure-48 VDC Power System 502NGFB Bedienungsanleitung

Vertiv

Vertiv NetSure 8200 Series Bedienungsanleitung

Vertiv

Vertiv NetSure7100 Series Bedienungsanleitung

Vertiv

Vertiv NetSure 700NVBA Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung