VIA Technologies CM35-SC Bedienungsanleitung

CM35-SC

CM30-SC

Rev. A+

System Board

Users Manual

44400031

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98 and

Windows®2000 are registered trademarks of Microsoft

Corporation. Intel®, Pentium®III and CeleronTM are registered

trademarks of Intel Corporation. VIA CyrixIII is a registered

trademark of VIA Technologies, Inc. Award is a registered trademark

of Award Software, Inc. Other trademarks and registered

trademarks of products appearing in this manual are the properties

of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Read Me First..........................................................

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .............................................................................................

2.2 System Memory.............................................................................................................

2.3 Frequency Ratio Settings for Processors................................................

2.4 Jumper Settings for Selecting the CPUs Front Side Bus...............

2.5 Jumper Settings for Clearing CMOS Data..........................................

2.6 Jumper Settings for the Onboard Audio Codec...........................

2.7 Ports and Connectors.............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 VIA Hardware Monitor............................................................................................

4.3 VIA Service Pack..........................................................................................................

4.4 Audio Drivers and Software Application...............................................

4.5 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................

Introduction

Read Me First

This page contains a summary of the important notes that must be

given special attention to prior to using the system board.

Processor

 The frequency ratio of some processors may have been locked

by the manufacturer. If you are using this kind of processor,

setting an extended ratio for the processor will have no effect.

The system will instead use its factory default ratio.

 The frequency ratio of processors greater than 8x has been

locked by the manufacturer and will no longer have the flexibility

of using extended ratios. Therefore, the system will use the

processors factory default ratio.

 Selecting an external bus clock other than 66MHz, 100MHz or

133MHz may result to the processors or systems instability and

are not guaranteed to provide better system performance.

System Memory

The system board supports both VCM and PC SDRAM DIMMs. If

you are using more than one DIMM, make sure you insert the same

type of DIMMs into the DIMM sockets. Using different types (VCM

or PC SDRAM) of DIMMs may cause problems.

5VSB Power

 If you are using the (1) Wake-On-LAN and/or (2) Wake-On-

Ring (internal modem) functions, the 5VSB power source of your

power supply must support ≥720mA.

 If you are using the Suspend to RAM function, the 5VSB power

source of your power supply must support ≥1A.

Drivers

Make sure to reboot the system after each driver installation.

Problems will occur if you reboot only after installing all the drivers.

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA®8604/82C686A AGPset (PL133) - CM30-SC

 VIA®8605/82C686A AGPset (PM133) - CM35-SC

Processor

The system board is equipped with Socket 370. It is also equipped

with a switching voltage regulator that automatically detects 1.30V

to 3.5V.

 Pentium®III FCPGA 133MHz FSB (533EB-933EB) or 100MHz

FSB (500E-850E) processor

 CeleronTM 66MHz FSB: FCPGA (566MHz-700MHz) or PPGA

(300A-533MHz) processor

 VIA CyrixIII processor

System Memory

 Up to 1GB using VCM (Virtual Channel Memory) or PC

SDRAM DIMM (unbuffered or registered)

 Two 168-pin DIMM sockets

 Uses x64 PC SDRAM, 3.3V

- PC-66 SDRAM DIMM for 66MHz FSB processors

- PC-100 SDRAM DIMM for 100/66MHz FSB processors

- PC-133 SDRAM DIMM for 133MHz FSB processors

Chapter 1 - Introduction

Note:

If you are using more than one DIMM, make sure you insert

the same type of DIMMs into the DIMM sockets. Using

different types (VCM or PC SDRAM) of DIMMs may cause

problems.

Introduction

Expansion Slots

The CM35-SC system board is equipped with 1 shared AGP / DFP

(Digital Flat Panel) slot while CM30-SC is only equipped with the

DFP slot.

The AGP slot on the CM35-SC system board is a universal AGP

slot. AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 2x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

Both system boards are also equipped with 2 dedicated PCI slots

and 1 shared AMR/ISA slot. AMR (Audio/Modem Riser) is an

interface designed for installing an audio riser card, modem riser card

or audio/modem riser card that is compliant to the AMR

specification.

Onboard Graphics Features

 Integrated Savage4 2D/3D/Video accelerator

- Shares 1MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- Full AGP 4x, including sideband addressing and execute mode

- High quality DVD video playback

 3D rendering features

- 32-bit true color rendering

- MPEG-2 video textures

 2D hardware acceleration features

 Motion video architecture

 Software drivers

- Windows®95/98/2000

- Windows NT®4.0

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Onboard Audio Features

 Supports Microsoft®DirectSound/DirectSound 3D

 AC97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One NS16C550A-compatible DB-9 serial port

 One DB-15 VGA port

 One SPP/ECP/EPP DB-25 parallel port

 One mini-DIN-6 PS/2 mouse port

 One mini-DIN-6 PS/2 keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for 2 additional external USB ports

 One 9-pin connector for 1 external serial port

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two 2.88MB floppy

drives

 One 20-pin ATX power supply connector

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU and chassis fan connectors

 Three internal audio connectors (AUX-in, CD-in and TAD)

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33 or ATA/66 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP

Introduction

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the HPSIR and ASKIR

standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J23

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB ports, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows®95/98/2000 Plug and Play compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI 2.0 function

 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VIA Technologies Hauptplatine Handbücher

VIA Technologies

VIA Technologies VAB-630 Bedienungsanleitung

VIA Technologies

VIA Technologies K8T800 Bedienungsanleitung

VIA Technologies

VIA Technologies VAB-950 Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-MII Bedienungsanleitung

VIA Technologies

VIA Technologies NAS 7800 Bedienungsanleitung

VIA Technologies

VIA Technologies VB7002 Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-P820 Bedienungsanleitung

VIA Technologies

VIA Technologies VAB-820 Bedienungsanleitung

VIA Technologies

VIA Technologies VAB-630 Bedienungsanleitung

VIA Technologies

VIA Technologies P4PB ULTRA-URL Bedienungsanleitung

VIA Technologies

VIA Technologies PT-TVBT Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-M930 Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-EX15000G - VIA Motherboard - Mini ITX Bedienungsanleitung

VIA Technologies

VIA Technologies VAB-1000 Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-M900 Bedienungsanleitung

VIA Technologies

VIA Technologies COMe-8X90 Bedienungsanleitung

VIA Technologies

VIA Technologies Zida BX983D Bedienungsanleitung

VIA Technologies

VIA Technologies P4M890DMP VT8237R Plus Bedienungsanleitung

VIA Technologies

VIA Technologies P4M800 Pro Gebrauchs- und Pflegehandbuch

VIA Technologies

VIA Technologies EPIA-N800 Bedienungsanleitung

VIA Technologies

VIA Technologies P4M266A Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-M850 Bedienungsanleitung

VIA Technologies

VIA Technologies EPIA-SP8000E - VIA Motherboard - Mini ITX Bedienungsanleitung

VIA Technologies

VIA Technologies 7001G - VIA Mini ITX Motherboard Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung