Viavi ALT-8000 Bedienungsanleitung

Figure 1-1 Power On Button

Radio Altimeter Test Procedure Using the

VIAVI ALT-8000/8015

The VIAVI ALT-8000/8015 RF-Based Portable Radio Altimeter Flight Line Test Set allows replication of in-

flight conditions by simulating altitudes, including climb/descend profiles, to verify your installed system and

isolate a bad component.

This document provides the basic instructions to test an installed system. With little editing, it can be easily

adapted to your aircraft platform for formal procedure development.

Contents

ALT-8000/8015 Test Setup ……………………………………………………………………………………. Page 1

Altitude Simulation Test via Direct-Connect ……………………………………………………….………… Page 5

Altitude Simulation Test via Coupler …………...…………………………………………………….………. Page 7

Profile Test – Direct or Coupler…...…………………………………………………………………………… Page 9

Radio Altimeter Sensitivity Test – Direct or Coupler …….……….………………………………….……. Page 13

ALT-8000/8015 Test Setup

Radio altimeter: Ensure the aircraft or bench test fixture is energized, however the radio altimeter should be

in the OFF condition.

ALT-8000/8015:

1. Press the Power On button on the front of the ALT-8000 to power on the test set. See Fig. 1-1.

Test Note

VIAVI ALT-8000/8015

Page 2

Figure 1-2 Launch Bar

2. On the launch bar, press the Test Setup function key. See Figure 1-2.

3. Locate the two 20 ft cables (P/N 88511 and 89527), the two 4 ft cables (P/N 91253 and 91255) or

the 100 ft cable set (P/N 88500), whichever will be used.

NOTE: The 20 ft cables will be referenced in this procedure.

4. Connect the cable with the yellow ends (P/N 88511) to the UUT:RX (Yellow) connector on the top

panel of the ALT-8000/8015. See Figure 1-3.

5. Connect the cable with the red ends (P/N 89527) to the UUT:TX (Red) connector of the ALT-

8000/8015. See Figure 1-3.

Figure 1-3 ALT-8000/8015 Top Panel

VIAVI ALT-8000/8015

Page 3

Figure 1-4 Test Setup Screen

Figure 1-5 Delay Calibration Screen

6. Connect the other ends of the 20 ft cables together, using one of the supplied TNC to TNC Adapters

(P/N 38353).

NOTE: For the Delay Calibration, the 20 dB attenuators should NOT be installed on the ALT-

8000/8015.

7. On the Test Setup screen, press the Delay Calibration button. See Figure 1-4.

8. On the Delay Calibration screen, press the Start button to start the delay calibration. See Figure 1-5.

NOTE: The calibration process is automatic. When delay calibration is complete, the Test Setup screen

is displayed.

VIAVI ALT-8000/8015

Page 4

Figure 1-6 Loss Setup Screen

9. Remove the TNC to TNC Adapter from between the TX and RX cables.

10. Set UUT Settings – UUT Detect Mode to Auto. See Figure 1-4.

11. Set RF Settings – Level Mode to Auto. See Figure 1-4.

12. On the Test Setup screen, press the Loss button to go to the Loss setup page. See Figures 1-4

and 1-6.

13. Locate the cable loss value listed on the cable connected to the UUT:TX port (Red) and enter this

value as Cable Loss – UUT:TX Cable Loss (Red). See Figure 1-6.

14. Locate the cable loss value listed on the cable connected to the UUT:RX port (Yellow) and enter this

value as Cable Loss – UUT:RX Cable Loss (Yellow) See Figure 1-6.

15. For coupler testing, enter 20 dB as Ext. Attenuation – UUT:RX Attenuation (Yellow) and for direct

connect testing, enter 40 dB as Ext. Attenuation – UUT:RX Attenuation (Yellow). See Figure 1-6.

NOTE: 20 dB attenuators are only required for pulse type radio altimeters. They are not used for

FMCW and FMCW-CDF type radio altimeters.

16. Locate the coupler with the red UUT:TX label and then locate the Loss Value label on the coupler.

Enter the Coupler Loss Value as Coupler Loss – UUT:TX Coupler Loss (Red). See Figure 1-6.

17. Locate the coupler with the yellow UUT:RX label and then locate the Loss Value label on the

coupler. Enter the Coupler Loss Value as Coupler Loss – UUT:RX Coupler Loss (Yellow). See

Figure 1-6.

VIAVI ALT-8000/8015

Page 5

Figure 2-1 Test Setup - Direct

Altitude Simulation Test via Direct-Connect

1. Perform the ALT-8000/8015 Test Setup instructions beginning on page 1.

2. Ensure that two of the 20 dB TNC attenuators are connected to the UUT:RX Port (Yellow) of the

ALT-8000/8015. Connect one 20 dB attenuator directly to the ALT-8000/8015 and then connect the

second 20 dB attenuator directly to the first one. Then connect the coax to these attenuators.

NOTE: 20 dB attenuators are only required for pulse type radio altimeters. They are not used for

FMCW and FMCW-CDF type radio altimeters.

3. Connect the red coaxial cable to the TX port of the radio altimeter being tested. Connect the yellow

coax to the RX port of the radio altimeter being tested.

4. Apply power to the radio altimeter being tested.

5. Set RF Settings – Connection Type to Direct. See Figure 2-1.

6. Touch the gray vertical bar on the left side of the display to display the launch bar.

7. On the launch bar, press the Simulation function key. See Figure 1-2 and 2-2.

VIAVI ALT-8000/8015

Page 6

Figure 2-2 Simulation Screen

8. Ensure Control – Simulation is set to Manual. See Figure 2-2.

9. Set Control – Altitude to 100 ft. See Figure 2-2.

10. Press the Run button to start the altitude simulation. See Figure 2-2.

11. Ensure that an RF value is displayed in the UUT Parameters – Power (at UUT) window. If no power

is displayed, check your connections and power to the UUT. See Figure 2-3.

12. Verify that the UUT Parameters are all within the desired range.

13. Verify that the display on the RADIO ALTIMETER displays approximately 100 ft.

NOTE: The Delay Settings – Altitude Offset setting may be adjusted to make the display read

exactly 100 ft. See Figure 2-1.

14. Press the Control - Altitude Pause button to change the simulated altitude. See Figure 2-3.

15. Set Control - Current Altitude to desired test altitude (i.e. 500 ft, 1000 ft, 1500 ft.) up to maximum

altitude capable for your radio.

16. Verify that the UUT Parameters are all within the desired range.

NOTE: Link margin is only displayed for pulse type radio altimeters.

17. Verify that the display on the RADIO ALTIMETER displays approximately the same as the Control

Current Altitude setting.

18. Press the Stop button to stop the altitude simulation. See Figure 2-3.

VIAVI ALT-8000/8015

Page 7

Figure 2-3 Simulation Screen

Altitude Simulation Test via Coupler

1. Perform the ALT-8000/8015 Test Setup instructions beginning on page 1.

2. Ensure that one of the 20 dB TNC attenuators is connected to the UUT:RX Port (Yellow) of the ALT-

8000/8015. Connect the 20 dB attenuator directly to the ALT-8000/8015 and then connect the coax

to the attenuator.

NOTE: 20 dB attenuators are only required for pulse type radio altimeters. They are not used for

FMCW and FMCW-CDF type radio altimeters.

3. Locate the UUT:RX (Yellow) coupler and connect it to the UUT:RX (Yellow) cable.

4. Adjust the support poles to a length that will allow the compression poles to press the couplers into

the aircraft just tight enough to hold the couplers in place.

5. Place the UUT:TX (Red) coupler over the TX antenna, with the arrow pointing toward the front of the

aircraft.

NOTE: Some aircraft may have the antennas oriented toward each other and not toward the front of

the aircraft. To determine the orientation, rotate the coupler 90 degrees at a time while watching the

output power reading on the ALT-8000/8015. The highest power measurement indicates the correct

placement of the coupler and the orientation of the antenna. Leave the coupler in the position that

produced the highest power measurement.

VIAVI ALT-8000/8015

Page 8

6. Place the UUT:RX (Yellow) coupler over the RX antenna, with the arrow pointing toward the front of

the aircraft.

NOTE: If the TX antenna coupler is oriented toward the front of the aircraft, then orient the RX

coupler toward the front of the aircraft. If the TX antenna coupler is pointed toward the RX antenna,

then orient the RX coupler toward the TX antenna coupler.

7. Touch the gray vertical bar on the left side of the display to display the launch bar.

8. On the launch bar, press the Simulation function key. See Figures 1-2 and 2-2.

9. Ensure Control – Simulation is set to Manual. See Figure 2-2.

10. Set Control – Altitude to 100 ft. See Figure 2-2.

11. Press the Run button to start the altitude simulation. See Figure 2-2.

12. Ensure that an RF value is displayed in the UUT Parameters – Power (at UUT) window. If no power

is displayed, check your connections, coupler positioning, and power to the UUT. See Figure 2-3.

13. Verify that the UUT Parameters are all within the desired range.

14. Verify that the display on the RADIO ALTIMETER displays approximately 100 ft.

NOTE: The Delay Settings – Altitude Offset setting may be adjusted to make the display read

exactly 100 ft. See Figure 2-1.

15. Press the Control - Altitude Pause button to change the simulated altitude. See Figure 2-3.

16. Set Control - Current Altitude to desired test altitude (i.e. 500 ft, 1000 ft, 1500 ft.) up to maximum

altitude capable for your radio.

17. Verify that the UUT Parameters are all within the desired range.

18. Verify that the display on the RADIO ALTIMETER displays approximately the same as the Control–

Current Altitude setting.

19. Press the Stop button to stop the altitude simulation. See Figure 2-3.

VIAVI ALT-8000/8015

Page 9

Figure 4-1 Profile Setup Screen

Profile Test – Direct or Coupler

1. Perform the ALT-8000/8015 Test Setup instructions beginning on page 1.

2. Perform one of the two following steps depending upon whether you are direct-connecting or using a

coupler.

- Direct-Connect: Locate two of the 20 dB TNC attenuators and connect both to the UUT:RX Port

(Yellow) of the ALT-8000/8015. Connect one 20 dB attenuator directly to the ALT-8000/8015

and then connect the second 20 dB attenuator directly to the first one. Then connect the coax to

these attenuators. Ensure that 40 dB is entered as the Test Setup – Loss – Ext. Attenuation –

UUT:RX Ext Attenuation value.

- Coupler: Locate one of the 20 dB TNC attenuators and connect it to the UUT:RX Port (Yellow)

of the ALT-8000/8015. Connect the 20 dB attenuator directly to the ALT-8000/8015 and then

connect the coax to the attenuator. Ensure that 20 dB is entered as the Test Setup – Loss –

Ext. Attenuation – UUT:RX Ext Attenuation value.

3. Set RF Port Settings – Connection Type to Direct or Coupler. See Figure 2-1.

4. Touch the gray vertical bar on the left side of the display to display the launch bar.

5. On the launch bar, press the Profile Setup function key. See Figures 1-2 and 4-1.

6. To add a leg to the profile, press the Add button and the Add Leg pop-up window will be displayed.

See Figures 4-1 and 4-2.

VIAVI ALT-8000/8015

Page 10

Figure 4-2 Profile Setup

7. Enter a Start Altitude of 100 ft.

8. Enter a Stop Altitude of 100 ft.

9. Enter a Leg Duration of 30 s.

10. Press the Enter button to add Leg 1 to the profile. See Figures 4-2 and 4-3.

11. Press the Add button and the Add Leg pop-up window will be displayed again. See Figures 4-1, 4-2

and 4-3.

12. Enter a Start Altitude of 100 ft.

13. Enter a Stop Altitude of 500 ft.

14. Enter an Altitude Rate of 1000 ft/min.

15. Press the Enter button to add leg to the profile. See Figures 4-2 and 4-3.

Andere Handbücher für ALT-8000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viavi Messgerät Handbücher

Viavi

Viavi SmartPocket OLP-35SC Bedienungsanleitung

Viavi

Viavi Xgig Bedienungsanleitung

Viavi

Viavi WiFi Advisor WFED-300AC Bedienungsanleitung

Viavi

Viavi FBP-SD4IP-PRO Bedienungsanleitung

Viavi

Viavi DSP TDR Bedienungsanleitung

Viavi

Viavi CAA06M Bedienungsanleitung

Viavi

Viavi SmartPocket OLS-34V2 Bedienungsanleitung

Viavi

Viavi CPRIAdvisor CAP-100 Bedienungsanleitung

Viavi

Viavi SmartPocket OLP-37XV2 Bedienungsanleitung

Viavi

Viavi SmartClass OLP-87 Bedienungsanleitung

Viavi

Viavi 3550 Stücklistenhandbuch

Viavi

Viavi G4-PT-040-8T Handbuch

Viavi

Viavi VSE-1100 Bedienungsanleitung

Viavi

Viavi SmartPocket OLP-37X2 Bedienungsanleitung

Viavi

Viavi FiberChek Sidewinder Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi OneExpert CATV Bedienungsanleitung

Viavi

Viavi T-BERD 6000A V2 Stücklistenhandbuch

Viavi

Viavi Seeker X Bedienungsanleitung

Viavi

Viavi G3-GSP-8P-8TSSD Handbuch

Viavi

Viavi MPOL*-85P Bedienungsanleitung

Viavi

Viavi CellAdvisor JD700B Series Bedienungsanleitung

Viavi

Viavi FIT-82P01-PRO Bedienungsanleitung

Viavi

Viavi WiFi Advisor WFED-300AC Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung