Viavi SmartClass Fiber MPOLx Stücklistenhandbuch

VIAVI Solutions

Quick Card

SmartClass Fiber MPOLx

Testing MPO/MTP terminated 12-strand fiber

This quick card describes how to use the VIAVI MPOLx for troubleshooting and loss/length MPO fiber

certification.

Equipment Requirements:

•MPOLx MPO test kit which will include:

oMPOLP-85(P) –MPO Power Meter

oMPOLS-8x(P) –MPO Light Source

oMPO/MTP FMAE adapter (APC for SM, PC for MM) (P versions)

o2x unpinned to unpinned Type A launch cords

o1x pinned to pinned Type A test cord

o2x MPO mating adapters

•The latest SmartClass Fiber firmware

oTo download the latest version visit http://scf.updatemyunit.net

•FiberChek PRO software with version 2.02 or newer

oTo download the latest version visit http://fcpro.updatemyunit.net/

•MPO Cleaning Tool

Configure the MPOLP-85P for the type of testing you will be performing:

•Create and set-up a project on the MPOLP:

oFrom home screen press the management icon (left side of touch screen, middle icon).

oSelect projects, press menu button, and select add.

oType the name of the project, tap the check mark to save.

oAdd a description, set the label prefix, label index, and auto increment as desired.

oPress the back button and set the project to Active.

•Create and save the test configuration for the Loss/Length test you wish to perform:

Note: Setup can only be done on the MPOLP and not the MPOLS.

oFrom home screen select Loss/Length.

oPress the menu button.

oSelect a pre-set test configuration or create a new one as follows:

▪Select add –and name the test configuration (e.g. “SMF 12 Strand Test”). Select this

new test configuration and create a setup for a basic loss/length test:

•Fiber Type = MM/SM as appropriate

•Test Limit –Link Validation. Polarity A, Length 100 meters

•Cable Name: OM4/OS1 as appropriate

•Cable and Connector: as appropriate

•Test Reference Method: 1 Jumper

•Pass/Fail Fiber Selection: as appropriate

•Ensure the Patch Cord Microscope (PCM) settings are correct (if equipped) –using

correct inspection profile (Ribbon, SM or MM (IEC-61300-3-35 Ed. 2.0) ensures the

correct illumination of the end face.

•Adjust the focus and Y axis. Turn auto-center off.

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Set the reference between the two units prior to testing:

•IMPORTANT: Inspect all end-faces of the test cords using the built-in patch cord microscope

and clean if necessary.

•Connect the units together using the supplied unpinned-to-unpinned cable as shown above.

•Units will “beep” and show a graphic indicating they are connected.

•Press the Set Reference button.

•Unit will inform you “Referencing successfully completed”. If unsuccessful, re-inspect all fiber

end faces, clean where necessary, and try referencing again.

Verify that the reference was performed properly:

•Disconnect the launch cord from the MPOLP only. Leave the cord plugged into the MPOLS.

•Add the un-pinned to un-pinned receive cord to the MPOLP.

•Add two adapters (couplers) to the end of the launch cord on the MPOLP and MPOLS.

•Connect the supplied pinned to pinned cord between launch and receive cords.

•Note the units indicate they are connected via sound and screen indicator.

•Press auto-test –top right of screen or via menu –and review the loss measured when testing

through the couplers only.

oEnsure loss is below 0.7dB on all fibers

Perform a Loss/Length Test:

•Remove the center cord from the verification test set up.

•Replace the center (pinned-to-pinned) test cord with the fiber you wish to test, by connecting

the launch cord from the MPOLS and the receive cord attached to the MPOLP to the fiber you

wish to test.

•From the menu screen, press the AUTO TEST button.

•Results are stored simply by pressing the key key.

Create Test Reports:

•Using the supplied USB to micro USB cable, attach the MPOLP to a PC with the latest version of

FiberChek Pro running on it.

•FiberChek Pro will automatically recognize the MPOLP device and begin to load the project data

that is stored on the device.

•Check the box next to the project that contains the test results you would like to generate a pdf

report for.

•Click on the IMPORT PROJECTS button in FiberChek Pro.

•Test reports will be generated in pdf format and saved in the location listed at the top of the

screen in FiberChek Pro.

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi NSC-100 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi ComXpert CX100 Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV 620 Bedienungsanleitung

Viavi

Viavi OLA-54 Bedienungsanleitung

Viavi

Viavi FBP-HD4iP Bedienungsanleitung

Viavi

Viavi OneExpert DSL Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi SmartPocket OLP-39G Bedienungsanleitung

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi SmartClass OLP-85 Series Bedienungsanleitung

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi OneAdvisor ONA-800 Bedienungsanleitung

Viavi

Viavi OneExpert DSL ONX-580 Bedienungsanleitung

Viavi

Viavi ALT-8000 Stücklistenhandbuch

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi SmartOTDR Mainframe Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi Seeker X with MCA III Bedienungsanleitung

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 2000 Bedienungsanleitung

Viavi

Viavi SmartOTDR 100 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung